Link
See Also: Camera Link
-
Product
PXI-8368, MXI-Express Interface with Connector for Fiber Cable, PXI Remote Control Module
783934-01
Remote Control
MXI-Express Interface with Connector for Fiber Cable, PXI Remote Control Module—The PXI‑8368 allows you to control PXI and CompactPCI systems from your PC using a fully transparent MXI‑Express link. It is installed in a PXI chassis and uses a PCI Express‑to‑PCI bridge to interface with an installed PCI‑8366 through a copper, x1 MXI‑Express cable. The fiber-optic cabling of the PXI‑8368 provides electrical isolation between the PC and PXI chassis, as well as cabling up to 200 m per link.
-
Product
C012 Communication Board
MS 1728/29
-
- Suitable for standard desktops- Four channel in single board- Up to 10 Mbits/sec operating speed- Low Cost solution- Standard INMOS link protocol- Communicates with transputers- Converts between serial link and parallel bus- Tristate bidirectional bus interface- Memory mapped registers- Interrupt capability- TTL compatibility
-
Product
PXI/PXIe High Density 2A Multiplexer, 1-Bank, 128-Channel, 1-Pole
42-614D-015
Multiplexer Module
The 40-614D-015 (PXI) and 42-614D-015 (PXIe) 1-bank, 128-channel, 1-pole multiplexers are part of the High Density 2A multiplexer module range available in 23 configurations (see 'Also in this Range' link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
Automated Fibre Loss Test Set
LTS-1500
-
The LTS-1500 is a small, rugged automated fiber optic loss test set that characterises singlemode fiber links at wavelengths of 1310, 1490 and 1550 nm. It is comprised of a sensitive InGaAs based optical power meter calibrated at six wavelengths with better than -75 dBm noise level plus a stabilised laser light source with up to three selectable wavelengths.
-
Product
PXI MUX 4 Bank 0f 16 Channel 1 Pole
40-610-021-4/16/1
Multiplexer Module
This series of high density multiplexer modules feature a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector. Inter-bank linking relays allow multiplexer size to be increased in multiples of in multiples of three by joining the common terminals of adjacent banks. Closing one linking switch produces a 6-channel multiplexer, closing all linking switches produces an 54-channel multiplexer
-
Product
Signal Integrity TDR and VNA Software
80SICON IConnect
-
IConnect software is the efficient, easy-to-use, and cost-effective solution for measurement-based performance evaluation of gigabit interconnect links and devices, including signal integrity analysis, impedance, S-parameter and eye diagram tests, and fault isolation.
-
Product
10G/100GBASE-KR 64b/66b and Link Training Decode/Trigger Software
D9010EKRP
-
Advanced PCIe Protocol Decode/Trigger Software (PCIe 4/3/2/1, SATA/SAS).
-
Product
Multi Wavelength Monitor
LV5490/LV5480
-
The LV 5490 is a multi waveform monitor that supports 4K video format (4096×2160、3840×2160) based on 3G-SDI dual link or quad link, HD-SDI quad link, and 12G-SDI. The following two 4K video division transmission systems are supported. ・2-SAMPLE INTERLEAVE DIVISION ・SQUARE DIVISION
-
Product
Fiber Testers
-
The PingerPro Series provides a powerful combination of physical layer tools to troubleshoot copper/fiber links and LAN tools to identify and repair a wide range of network problems.
-
Product
USB License Key
Sentinel RMS
-
For customers that wish to use our software on different computers we offer the possibility to purchase our software license locked to a USB dongle. Add this product to your software order and we’ll deliver your software licenses linked to a compact Sentinel RMS license key.
-
Product
PXI 18 Bank, 3 Channel, 1 Pole Multiplexer
40-617-021
Multiplexer Module
The 40-617 18-Bank, 3-Channel, 1-Pole Multiplexer Module forms part of the System 40 PXI Programmable Switching system. The Module consists of 18 electrically isolated banks of multiplexers controlled by a PXI/PCI interface. Each bank is a 1 to 3 multiplexer and operates with break-before-make action when a new channel is selected. Any Individual multiplexer bank can have a channel set by itself, alternatively, multiple banks can have channels selected simultaneously. Inter-bank linking relays allow multiplexer size to be increased in multiples of 3 by joining the common terminals of adjacent banks. Closing one linking switch produces a 6 channel multiplexer, closing all linking switches produces an 54 channel multiplexer.
-
Product
16-bank, 4-channel, 2 pole version is part of the 40-614C High Density 2A Multiplexer
40-614C-002
Multiplexer Module
This 16-bank, 4-channel, 2 pole version is part of the 40-614C High Density 2A multiplexer module range that is available in 20 configurations (see Also in this Range link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
6U VPX Computing Payload
VP62108
-
LinkedHope Intelligent Technologies Co.,Ltd.
VP62108 is a 6U VPX computing payload based on Intel® 4th generation Core™ Processor. It supports Intel® 4th generation Haswell architecture i3/i5/i7 dual-core or quad-core embedded processor, up to quad-core i7 processor 4860EQ with a life cycle of more than 7 years.VP62108 provides four serial RapidIO (SRIO) x4 links for VPX data plane communications, two x8 PCIe links for VPX expansion plane communications and four Gigabit Ethernet links for VPX control plane communications. Its rich data exchange capability allows users to easily build the whole machine or system-level solutions.VP62108 supports up to DDR3L 16GB ECC memory and offers reliable data transmission. Its onboard solid state Flash managed by a SATA interface controller can be up to 64GB SLC or 128GB MLC. And the entire board uses the reinforced conduction-cooled design and has a wide operating temperature, allowing the user not to worry about its working stability in harsh environments. This feature makes VP62108 particularly suitable for critical mission areas.
-
Product
4-Port PCI Express CoaxPress 12 Frame Grabber
PCIE-1164-AE
Frame Grabber
Half-Size PCI Express Board Gen 3.0 x8CXP speeds range from 3.25 to 12.50 Gb/SSupports 1 to 4 CXP-12 camerasSupports power for all cameras with SafePower (up to 13 Watts per link)Supports NVIDIA GPUDirectFull GenICam support for control and captureSupports quadrature encoders
-
Product
Serial FPDP Extreme 1/2 ATR Recorder
Talon RTX 2596
-
- Rugged 1/2 ATR MIL-spec chassis for harsh mechanical and thermal environments- Environmentally sealed, conduction-cooled- Fully sealed for RF emissions with EMI power line filter- MIL-STD circular connectors- Compact and lightweight design - 18 lb (8 kg)- QuickPac® drive packs allow quick removal of all data storage up to 61 TB via the front panel- Ideal for UAVs, military vehicles, aircraft pods and outdoor environments- Four-channel Serial FPDP record/playback- Supports Flow Control, CRC, and Copy/Loop Mode as a receiver and transmitter- Supports 1.0625, 2.125, 2.5, 3.125 and 4.25 GBaud link rates- Single-mode and multi-mode fiber interfaces available- Sustained real-time record rates up to 4 GB/s- 12 to 28 VDC power supply- Optional GPS receiver for precise time and position stamping- SystemFlow API, GUI and Signal Viewer analysis tools- Optional telnet remote connection to recorder
-
Product
Advanced Monitoring Probe
DVB-C QAM
-
Combined with a Network Monitoring System or not, the EdgeProbe Advanced provides a powerful broadcast network alert & diagnosis tool allowing DTV network operators to monitor global trends and anticipate potential failures.EdgeProbe Advanced is able to monitor DVB-C and DVB-C2 signals at transmitter outputs, through its RF inputs (up to 4 in 1RU), as well as at modulator input and at Head-End/distribution links, through its ASI and IP inputs.
-
Product
PCIe-8371, x4 Gen1 PCI Express Host, 832 MB/s, Copper Cable MXI-Express Device for PXI Remote Control
779723-01
Remote Control
The PCIe‑8371 is an MXI‑Express remote controller for devices or systems cabled over PCI from a computer with a PCI Express slot. The PCIe‑8371 remote controller provides a x4 PCI Express link over a copper cable to the PXIe‑8370 remote control module when used for PXI system control. This link is transparent to software applications and drivers, so computers and servers can control connected devices with no additional programming. With NI remote controllers, PXI modules can be used as if they are PCI devices directly installed in the computer.
-
Product
13-slot ATX-supported PICMG1.3 Bus Passive Backplane
FAB114
-
The FAB114 has a PICMG 1.3 CPU card slot, one PCI Express x16 slot, three PCI Express x1 slots and a total of eight 32bit/33MHz PCI slots. The onboard 24-pin ATX power connector and 8-pin connector for thermal detected board are featured. Through one PCIe x16 link, this PICMG 1.3 backplane maximize the performance of high-end PCI Express graphics and video cards. Furthermore, the backplane supports two high speed USB 2.0 ports. The FAB114 is perfect fit for AXIOMTEK's SHB100 and SHB110. AXIOMTEK also offers versatile 4U industrial chassis specially design for the FAB114, such as the AX61400, AX6156 series and AX61491.
-
Product
PXIe-1487, 8 Input, 8 Output, or 4 Input/4 Output PXI FlexRIO GMSL™ Interface Module
787457-01
Interface
The PXIe-1487 combines the Maxim Integrated Gigabit Multimedia Serial Link™ (GMSL™) interface with the Xilinx FPGA for high-throughput vision and imaging applications. This module provides a high-speed digital interface for using and testing modern advanced driver assistance systems (ADAS) and autonomous drive (AD) camera sensors and electronic control units (ECUs). Additionally, the PXIe-1487 makes use of a combination of GMSL™ serializers and deserializers with a Xilinx FPGA to provide a high-throughput and customizable GMSL™ interface on PXI. The included FlexRIO driver, with LabVIEW FPGA examples, provides access and control for power-over-coax, I²C back-channel communication, and general-purpose input/output (GPIO) communication on the GMSL™ channels. The PXIe-1487 is ideal for applications such as in-vehicle data logging, lab-based playback, or hardware-in-the-loop (HIL). GMSL is a trademark of Maxim Integrated Products, Inc.
-
Product
Micro-Ohmmeters
RMO-G Series
-
The RMO-G is a portable micro-ohmmeter designed for contact resistance measurement of non-inductive test objects and applications with increased safety requirement. It tests medium and high-voltage circuit breakers, disconnecting switches, high-current bus bar joints, cable splices, and different high-current links. Due to its Both Sides Grounded and Remote Control functionalities, the instrument accurately measures even in the most demanding environments, providing additional safety to testing personnel.The RMO800G is the most powerful portable micro-ohmmeter on the market with 800 A output current. RMO200G is our best seller in the USA. A user can choose the appropriate model depending on the output current requirement, from 100 A (RMO100G) to 800 A (RMO800G).We use an unbreakable plastic case with IP67 protective rating (with closed lid) for instruments’ housing. Although very portable and lightweight, RMO-G micro-ohmmeters have very high output power capabilities. High output voltage enables a wider measurement range at higher test currents. Consequently, it enables the usage of thinner/longer test cables. RMO-G generates a true DC ripple-free (less than 1 % ripple) current with automatically regulated test ramps. During the testing, it increases current before measuring and decreases current after the measurement. This significantly decreases magnetic transients and ensures great accuracy.Special current clamps measure a current through groundings when the instrument tests in Both Sides Grounded conditions. The instrument itself powers these clamps. If even higher safety level is required, the Remote Control feature enables the operator to perform measurements from distant locations.RMO-G instruments can store up to 500 measurements in internal memory. Also, they have a built-in thermal printer and USB flash drive available as an option. An additional option is the built-in High Precision module suitable for measurement of very low resistance, in the range from 1 to 30 µΩ, with 0,01 µΩ resolution.Our free DV Win software communicates with the RMO-G micro-ohmmeters via USB or RS232 interface. It allows a user to run the test remotely from a PC. Also, a user can download test results, analyze and generate fully configurable test reports through the software.
-
Product
CompactPCI Serial 9 Slot 4U
-
The CompactPCI® Serial 9-slot chassis is based on the novel standard that relies on serial point-to-point interconnections. It overcomes the bandwidth limitation of the parallel CompactPCI bus and allows for PCI-E, SATA, USB, and Ethernet links among the cards. The chassis is a light-weight unit with powerful cooling and redundant power supplies. It perfectly suits a wide range of applications from lab usage to multi-system arrangement in a rack.
-
Product
Corona Effect Camera
CoroCAM 8 UAV
-
*High-sensitivity UV detector, which can detect UVc light at 2.05×10-18 Watt/cm2, this allows detection of the smallest corona discharges.*9Hz (or 25Hz optional) IR radiometric camera module*Control of a limited number of camera functions from a standard RC controller using PWM or SBUS.*Remote control of all camera functions from the laptop via an Ethernet link.*Soft sync or staggered zoom of the 3 channel cameras. The IR and UV channels are digitally zoomed in, which is visible...optically zoomed in to the minimum FOV, and then digitally zoomed out.
-
Product
Media Converter, 100Mbps, Multimode 1310nm, 2km, SC
EKI-2541M
-
Provides 1 x 10/100 Mbps Ethernet port with RJ45 connectorProvides 1 x 100 Mbps Multi-mode SC type fiber portProvides internal jumper for Link Fault Pass-through (LFP) settingSupports full/half duplex flow controlSupports store and forward transmissionSupports auto-negotiationSupports MDI/MDI-X auto crossoverSupports redundant 12-48 VDC power inputProvides flexible mounting: DIN-rail and Panel mount
-
Product
Optical Fiber Ranger
-
Optical fiber ranger is test equipment that functions similar to an optical time domain reflectometer. It is used in single mode fiber test applications. The fiber optic ranger is much smaller size and lighter weight compared to the fiber optic OTDR, and it is much more cost effective. They are used in optical fiber links troubleshooting, maintenance and test.
-
Product
FCC Certification
-
Here we provide access to information about the FCC authorization methods, excerpts of FCC rules that cover marketing of devices in the United States as well as general terms and definitions used in within the FCC authorization scheme. To file an application for certification at any time, please click the “Service Quote” link above or contact us today.Telecommunication Certification Bodies (TCBs) have been appointed by the Federal Communications Commission (FCC) to approve equipment as required under Title 47, Part 2 of the Code of Federal Regulation (CFR).In essence, this gives you, the manufacturer or responsible party, additional options for product approvals by allowing you to choose from one of many TCBs.Information presented here is derived from FCC CFR Title 47. Please see the FCC CFR web page for access to the official rules or vist Title 47 at e-CFR.
-
Product
PathWave BenchVue USB Modular Function Generator Pro
BV0022B
-
The BenchVue USB function generator pro connects and configures the function generator and links to the Waveform Builder Pro for advanced custom waveforms.
-
Product
EDX-FTIR Contaminant Finder/Material Inspector
EDXIR-Analysis Contaminant Finder/Material Inspector
-
EDXIR-Analysis software is specially designed to perform qualitative analysis using data acquired by an energy dispersive X-ray (EDX) fluorescence spectrometer and a Fourier transform infrared spectrophotometer (FTIR). This software is used to perform an integrated analysis of data from FTIR, which is excellent at the identification and qualification of organic compounds, and from EDX, which is excellent at the elementary analysis of metals, inorganic compounds and other content. It then pursues identification results and the degree of matching. it can also be used to perform EDX or FTIR data analysis on its own. The library used for data analysis (containing 485 data as standard) is original to Shimadzu, and was created through cooperation with water supply agencies and food manufacturers. Additional data can be registered to the library, as can image files and document files in PDF format. It is also effective for the linked storage of various types of data as electronic files.
-
Product
Test Kits
-
Optical Wavelength Laboratories
Deluxe color LCD fiber link certifier (includes MASTER and REMOTE devices) Tests two fibers at a time, cutting testing time in half (when compared to traditional fiber certification) Ideal for installers and contractors who need to certify fiber cables BI-DIRECTIONALLY Measure the end-to-end length of the fiber cable with every test Unlimited sets of job parametersOWLView software allows tri-report capability certification, OTDR, and endface all on one report) Multimode and singlemode options available.
-
Product
PXI 2A Multiplexer, 1-Bank, 8-Channel, 16-Pole
40-614C-019
Multiplexer Module
This 1-bank, 8-channel, 16 pole version is part of the 40-614C High Density 2A multiplexer module range that is available in 20 configurations (see Also in this Range link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
3U Dual Flange Kit
34192A
-
Secure the instrument to the front of a System II cabinet; combine with the 34194A Dual Lock Link Kit to mount two System II instruments side by side
