EMI Test Systems
See Also: Faraday Cages
-
Product
Standard Test Systems
WaveCore™ Products
Test System
Textron Systems’ WaveCore family offers a variety of standard test systems with a primary application of satellite payload lab testing. Our systems can be deployed affordably for both production and engineering applications, providing industry-leading levels of data correlation with high system mean time between failures and low mean time to repair.
-
Product
Magnetic Material Test Fixture
16454A
Test Fixture
The 16454A is designed for accurate permeability measurements of toroidal-shaped magnetic materials. Since the construction of this fixture creates one turn around the toroid (with no magnetic flux leakage), the need of winding a wire around the toroid is unnecessary. Complex permeability is calculated from the inductance with and without the toroid. When the E4991A/4291B with option 002 is used as the measurement instrument, direct readouts of complex permeability are possible. In addition, it is furnished with a small and a large fixture to adapt to a wide range of sizes.
-
Product
Mezzanine System Carrier
MMS8010 / MMS8011
System
The Abaco ECM 3U VPX carrier supports up to six Abaco Systems Electrical Conversion Modules (ECMs) in a VITA 46 VPX form factor. Each ECM site connects 32 single-ended 3.3 V signals to the FPGA. The specific ECM board installed on a site converts the FPGA signals to 16 I/O signals, for a total of 96 I/O signals across the six ECM sites.
-
Product
Ground EMI Filters
-
High-frequency signals on ground is never good news - it interferes with normal operation of equipment and creates electrical overstress (EOS). However it is easy to block propagation of EMI on ground by installing highly-effective ground EMI filtes in ground lines. Our unique patent-pending ground EMI filters provide very low impedance for DC and mains' power while effectively blocking propagation of high-frequency currents throughout facility or equipment ground. Ground filters meet safety standards, as well as ANSI/ESD S6.1 and ANSI/ESD S20.20.
-
Product
Disk Drive Test System
Saturn
Test System
The Saturn HD is the industry leader in 3.5” Near-Line Hard Disk Drive (HDD) testing. It provides maximum throughput while minimizing factory floor space and power consumption. The system is designed to perform single insertion of SSW, BDSW and Burn-In as well as drive configuration. Using Saturn HD on the production floor will reduce drive build times, enable greater responsiveness to data center demands and lower test costs per HDD unit.
-
Product
VITA 62, 3U Test Fixture
TF-3U-7B041-1
Test Fixture
This Power Supply test fixture is being proposed as a tool for checking Injector / Ejector operation, proper alignment of the VITA 62 connector and proper alignment of both keys on a Single slot, 3U, VITA 62/SOSA power supply.
-
Product
Edge AI Inference System
AIR-020R
Edge AI Inference System
Edge AI Inference system powered by NVIDIA® Jetson Orin™ Nano and Super mode. Compact and performance AI box design. NVIDIA® Jetson Orin™ Nano 8GB/4GB built-in.
-
Product
Dynamometer Test Systems
-
Genuen provides a full range of off-the-shelf and custom dyno test cell solutions. We offer turnkey test cell integration services and test cell upgrades and modernization for all types of dynamometers used in automotive, aerospace, industrial, commercial, off-highway, and agricultural markets. Our broad-based expertise includes dynamometer test systems ranging from AC motor, hydrokinetic, hydrostatic, electric AC/DC, eddy current, and hysteresis brake.
-
Product
Test Systems
-
In-Circuit Test (ICT) tests populated circuit boards by means of electronic measurements through thin needles on test fixtures. We offer in-circuit testers for various testing strategies – from the flexible 19“ rack to the ergonomic high-performance tester. And all of our in-circuit testers are also available in the Lambda edition for true parallel testing. The flying probe test checks your printed circuit boards using four movable test heads. This requires no fixtures and allows for flexible test program generation. That makes our flying probe test systems ideal for a high mix of printed circuit boards and small to medium test volumes, such as for prototype testing.
-
Product
Brake Test Systems
GIANT 9000 Series
-
The major test target is to detect noise and vibrations generated by the vehicles brake. Our intention was to build a dynamometer that can operate either with brakes mounted to the complete vehicle, or with just the axle module mounted to a universal adaptor system or wheel suspensions.
-
Product
Plug-in Test Systems
-
FAME is the innovative, modular plug-in test system for measuring and testing tasks in protection technology for medium-voltage and high-voltage switchgear. The plug-in test system combines complex switching operations for testing the function of current transformers and voltage transducers, as well as tripping and signal contacts.
-
Product
Multi-Cell Test System
Cellcia
-
Next-generation wafer probing system for 300mm wafers. The multi-layer system structure maximizes the efficiency of testing, further reducing the total testing cost.
-
Product
Drop Test System
-
HIACC Engineering & Services Pvt. Ltd.
HIACC's Drop Test System is a specialized, automated testing apparatus designed to simulate real-world handling and transportation hazards, determining the "drop bearing capacity" (durability) of products and their packaging.
-
Product
microLED Testing System
OmniPix-ML1000
-
The OmniPix-ML1000 is the first all-encompassing microLED testing system, offering both full wafer and localized individual pixel inspection. Measure localized and total EQE. Use automated PL and EL to test and characterize your microLEDs. Analyze defective pixels with nano-PL and nano-EL.
-
Product
High-Temperature Test Systems
-
HT-PEM (high-temperature polymer electrolyte membrane) technology represents a further development of PEM fuel cell technology. Unlike conventional PEM fuel cells, which operate at lower temperatures, HT-PEM fuel cells can reach temperatures of up to 200 °C.
-
Product
EMI Tester
-
The EMI tester automatically measures the noise distribution of the electric field and the magnetic field radiated from electronic equipment with high accuracy.・ Even if PCB and IC parts have complicated bumpy shape and surface. The movable assembly can automatically trace them.・ EMI noise distribution is expressed as a variety of maps, such as 4D/3D/2D graphics and cross section view.
-
Product
EMI Test Receiver
KH3938B
-
Beijing KeHuan Century EMC Technology Co,.LTD
Is a fully automatic radio disturbance test receiver and is the main tool for EMI testing. KH3938B receivers frequency range 9kHz-1GHz, in accordance with: 2010 and GB / T6113.101-2016 development standards designed to meet the requirements of the standard-compatible, can be used to power emission test, Sao conduction disturbance voltage test, radiated disturbance within 1G test. The receiver has the advantages of fast test speed , strong maneuverability, stable performance, and convenient test data processing.
-
Product
Mezzanine System
5676
System
The Abaco SystemsP/N 5676 ECM module provides eight channels of 16 bit voltage measurement in the 0 to 2.5V volt range. For each channel the common mode voltage range is -100 volts to +100 volts.
-
Product
Pump Test System
-
This automated test system evaluates a wide range of performance metrics for a cooling pump assembly. The LabVIEW based system programs the DUT then initiates a series of tests to check:Serial communication verificationMotor voltage & currentImpeller speed and flowAir and water temperaturesLeak and level sensor functions
-
Product
Standalone Test System
1000 Series ATE
-
The Circuit Check 1000 Series ATE provides a configurable standard platform that can utilize multiple mass interconnect interfaces while providing ease of maintenance and the ability to accept a wide variety of test fixture solutions. With the 1000 Series ATE, test procedures become automatic, with test steps and go/no-go limits easily programmable.
-
Product
Automated Test System
-
Automated Test System is a production-ready solution that combines test software and various hardware for validation test in both manufacturing and R&D. The solution provides a high performance and cost-effective system based on National Instruments technology.
-
Product
Backplane Test System
402LV
-
Very High Pin Count Level IV Backplane Test System. To ensure that Testronics maintains its leadership position as the premier supplier of backplane testers, we will be introducing our solution to testing high pin count / very large backplanes, the Model 402.
-
Product
EMI Receiver
Core-6
-
The "CORE-6" is a very compact (19", 1 RU), new digital EMI receiver which enables the user to make frequency-sweeps within a few seconds what saves hours of measuring timeduring developments.
-
Product
Engine Test Systems
TITAN Engine
-
The TITAN engine test system series contains fully equipped engine test stands which are designed for various categories of internal combustion engines, ranging from light-to heavy-duty engines and also offering solutions for component tests such as testing the exhaust line. Further adjustment for off-road engines, powered two-wheeler engines, small internal combustion engines from carts, snowmobiles or motorboats as well as aircraft turbines are available. Additionally, it is also possible to test alternative engine concepts.
-
Product
Airbag Test System
-
Dongguan City Simplewell Technology Co. Ltd.
Airbag Test System by Simplewell
-
-
-
Product
Oil Test System
-
The Oil Test system Model OTS 2K1 is portable transformer oil Test system. It is a specially designed for accurate measurement of Loss Factor, Permitivity & Volume Resistivity Measurement of Transformer Oils & Petroleum jellys. The test frequency is 50 Hz . The system is provided with Mode Selector Switch so that once the oil cell is connected, it can measure all Three parameters in different modes without handling the test leads.
-
Product
SMD Array Type LCR Test Fixture
16034H
Test Fixture
The 16034H is designed for impedance evaluations of array-type SMD.The minimum SMD size that this fixture is adapted to evaluate is 1.6(L)x0.8(W)[mm]. Since the tip of the measurement electrodes are very thin and the device holder is extremely flat, the device can be shifted and the measurement electrodes can contact each of the elements of the array-type component.
-
Product
Tabletop Single Site Test Handler
3111
Test Handler
The Chroma 3111 is an automated pick & place handling system ideal for small lot engineering samples and/or NPI test development parts.
