-
Product
PCI Precision Resistor Card 9-Channel, 1.5Ω To 472Ω
50-297-020
Programmable Resistor Module
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Carrier Card
VIPC627-ET
-
VIPC627-ET is a 6U VME carrier card with four IP slots and extended temperature range. Two 50-pin, 0.1 inch flat ribbon cable connectors mounted in the front panel provide access to all IP I/O lines. Also, all I/O lines of 'IP D' are routed to VME P2 and 14 user selectable I/O lines of 'IP C' can be routed to VME P2 via a jumper field.
-
Product
FMC Card with DisplayPort Input and Output
TEF0007-02A
-
Sundance Multiprocessor Technology Ltd.
The Trenz Electronic TEF0007 is a DisplayPort 1.2 compatible FMC card with data rates up to 5.4 Gbps and sink and source DP connector. SN65DP159 is used as DP Retimer and SN75DP130 as DP Redriver to connect sink and source to on board Kintex-7 FPGA.Image stream over FMC can be realized over 4 MGTs (only 1 available on LPC) and 34 differential IOs (LPC compatible).
-
Product
PXI Programmable Resistor Card 4-Channel 2 Ohm to 127 Ohm - SPST
40-294-112
Programmable Resistor Module
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PCI High Density Potentiometer Card 4-Channel, 16-Bit, 0 To 65k Ohm
50-296A-121-4/16
Programmable Potentiometer
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXI Interface Cards
-
PXI is a modular instrument system designed to take advantage of fast data interfaces based on PCI and PCIe bus systems. Due to the large number of different PXI interface cards, the individual test system can be designed for almost all applications.
-
Product
PCI 4-Channel Precision Resistor Card
50-297-102
Precision Resistor Module
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXIe-SMN Interface Card
-
Avionics Interface Technologies
2.125 Gbps Optical loop networkSingle-mode and Multi-mode optical interfaces supportedUp to 256 Shared Memory Network nodes supportedUp to 200 MByte/sec sustained data ratesMaximum 500 nS latency between nodesNetwork interrupts supportedSoftware Drivers available for Windows (7/8), Linux, LabVIEW Real-Time, and VxWorks
-
Product
1-Channel Voltage Measurement Card
LQU3
-
Computer Gesteuerte Systeme GmbH
The LQU3 is a 1-channel voltage measurement card that features uni- and bipolar measurement modes. It offers 3 decades with 2 different amplifications. Therefore measurement ranges from +/- 1.6 V to +/- 320 V with a resolution of 16 bits and an accuracy of up to 0.02% are available.
-
Product
16, 32, And 48 Channel Isolated Solid-State Output Cards With External Clocking
PCI-IDO-xxA Series
-
PCI-IDO-xxA Series cards offer a range of 16, 32, or 48 individual, optically isolated differential outputs. These cards are ideal for use in control and instrumentation applications where high-voltage protection is required. Individual channel-to-channel isolation allows every channel to be physically and electrically separated from the others.
-
Product
PCI High Density Pecision Resistor Card, 3-Channel, 3.5Ω To 102kΩ
50-298-140
Programmable Resistor Module
The 50-298-140 is a high density programmable resistor card with 3 channels which can be set between 3.5Ω and 102kΩ with 0.125Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
(Compact PCI) GPIB Controller Card
Model 488-PXI
Controller
* Adds GPIB Controller capability to any PXI or Compact PCI System.* Fast >1 Mbs transfer rate* 488.2V4 Driver supports 32 and 64-bit Windows XP, Vista, Windows 7, 8 and Windows 10 with a true 64-bit DLL.* Compatible with industry standard 'ib' and '488.2' command sets.* Works with Agilent, NI and Kikisui VISA libraries.* ICS's Explorer auto configures your controller as it finds your instruments.* Program with Visual Basic, C, LabVIEW, Matlab or Agilent VEE* Most affordable PXI-GPIB controller card available.
-
Product
PCI 50xDPST Reed Relay Card
50-115A-122
Reed Relay
This is the 50xDPST version of our 50-110A/50-115A range of reed relay switching cards which are available in both Changeover (SPDT) and Normally Open (SPST & DPST) configurations. Connections are made via a front panel 200 pin female LFH connector.
-
Product
FPGA Workbench and I/O Cards
-
FPGA Workbench software provides a complete development environment for building customized solutions based on Concurrent’s programmable FPGA cards. FPGA Workbench includes a powerful GUI for selecting and configuring a wide range of pre-developed data acquisition and industry-specific modules to meet your application requirements. The library of functional IP modules includes pulse width modulation, analog I/O, digital I/O, SENT protocol, encoder, ignition, injection, crank/cam shaft, wheel speed sensor and change-of-state.
-
Product
PXI 2-Slot BRIC 24x8 Matrix, 2A 2-Pole (1 sub card)
40-565A-202-24X8
Matrix Switch Module
The 40-565A PXI Matrix BRIC is a range of high-density matrix modules able to switch up to 2 Amps at 150VDC/100VAC They are available in 2, 4 or 8 slot PXI sizes to suit most high-performance PXI Matrix requirements and constructed using quality electro-mechanical relays for high switching confidence.
-
Product
PCI Precision Resistor Card 18-Channel, 1Ω to 31.5Ω
50-297-010
Programmable Resistor Module
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
Four And Two-Port Multi-Protocol RS-232/422/485 M.2 Cards
M.2-COM-4SM Family
-
The M.2-COM-4SM family of cards feature high performance 16C950-class UARTs. Available in 4-port and 2-port versions, each port is capable of communication speeds up to 921.6kbps in RS-232 (differential modes support speeds as high as 3Mbps) and has 128-byte deep transmit and receive FIFOs. Large FIFOs protect against data loss in multitasking operating systems, reduce CPU utilization, and improve data throughput, while reducing or eliminating inter-character or inter-packet pauses. The advanced integrated circuit with pre-scalar supports a wide variety of custom baud rates, and any rates not otherwise achievable can be supported via a custom factory-installed crystal oscillator (up to 10Mbps!).
-
Product
PCI High Density Pecision Resistor Card, 3-Channel, 4Ω To 1.51MΩ
50-298-150
Programmable Resistor Module
The 50-298-150 is a high density programmable resistor card with 3 channels which can be set between 4Ω and 1.51MΩ with 0.125Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
96/48-CH Opto-22 Compatible PCI Express Digital I/O Cards
PCIe-7248/7296
Digital I/O
ADLINK"s PCIe-7248/7296 are high-density parallel digital I/O boards with 96/48 I/O channels. The header connectors are fully compatible with industry Opto-22 standard. Thus, PCIe-7248/7296 can utilize the Opto-22 external devices. The PCIe-7248/7296 devices emulate mode 0 of the industry standard 8255 programmable peripheral interface (PPI) chips. The PCIe-7248/7296 provides 4/2 PPI chips respectively. Each PPI offers three 8-bit ports: Port A, Port B and Port C. The Port C is divided into 2 nibble-wide (4-bit) ports. The PCIe-7248/7296 devices have programmable timer/counters. One 16-bit counter is available for event counting, while the other 32-bit timer is available for timed interrupt generation. The PCIe-7248/7296 devices provide multiple programmable interrupt sources from DIO channels, as well as the output of the timer.
-
Product
Analog Output DAQ Cards
-
Analog output cards are ideal for DAQ applications where multiple A/O channels are needed for voltage and current output.
-
Product
PCI To CardBus PCMCIA Type 1/2/3 Dual Slot Card, Ricoh R5C486 Controller
P222-Ricoh
-
The P222-Ricoh is perfect for use with Wireless LAN cards like WiFi / 802.11b or any of the newly emerging 802.11a or 802.11g standards and thanks to its second slot can simultaneously run a Bluetooth card or other type of PCMCIA or CardBus card.
-
Product
Intel® Smart Display Module Small (Intel® SDM-S) With Intel® Pentium® Processor N4200 & Celeron® Processor N3350
SDM300S
-
The SDM300S is a signage computer module following the newest Intel® Smart Display Module Small (Intel® SDM-S) architecture. The SDM300S is powered by the onboard Intel® Pentium® processor N4200 and Celeron® processor N3350 (code name: Apollo Lake) with the Intel® HD Graphics 505 or 500 chipset. The sleekest all-in-one display module measures only 100 x 60mm (roughly the size of a credit card), which makes for a thinner display. The SDM300S can be easily connected to an SDM-compliant display via a high-speed PCIe edge connector - which supports 4K resolution displays and video capture and has built-in USB 3.0, HDMI 1.4, DisplayPort 1.2, Serial TX/RX and I2C signals. Nearly a third the size of Open Pluggable Specification (OPS), the design of the SDM300S omits housing so it is well suited for space-constricting applications.
-
Product
PCI High Density Pecision Resistor Card, 6-Channel, 4Ω To 5.82MΩ
50-298-052
Programmable Resistor Module
The 50-298-052 is a high density programmable resistor card with 6 channels which can be set between 4Ω and 5.82MΩ with 0.5Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
10 Gbit Ethernet Card, PXIe Form Factor
ADQ10GBE
Ethernet Interface
The ADQ10GBE module enables fast network connection from a cPCIe/PXIe chassis to an external host computer. It occupies a single slot in an 3U cPCIe/PXIe chassis and can be used with backplanes supporting up to x8 Gen2 PCIe. All necessary software drivers are included and can be installed on the PXIe controller. ADQ10GBE can be used under Windows 7 (32 or 64 bit), Windows 8 and 8.1, and Linux (native support or ixgbe source code).
-
Product
32 Channel Optically Isolated Digital Card
104-IDIO-16 Family
-
The Model 104-IDIO-16 is a 32-channel PC/104 utility board featuring 16 optically isolated inputs and 16 optically isolated solid state outputs. The isolated, non polarized inputs may be driven by either DC sources of 3-31V (or higher by special order) or AC sources at frequencies of 40Hz to 10KHz. Optically isolating the digital inputs from each other, and from the computer, assures smooth, error-free data transmission in noisy, real-world environments. The 16 input channels are available via a 34-pin IDC type header. The fully protected solid state outputs, capable of sourcing 2A each, are inherently more reliable than electromechanical relays and give system architects a more robust product to design with. The solid state outputs are available via a 50 pin IDC type header.
-
Product
10-CH General-Purpose Timers/Counters & 8-CH Digital I/O Card
PCI-8554
Digital I/O
- Supports a 32-bit 5 V PCI bus- On-board four 82C54 programmable timer/counter chips- 10-CH independent 16-bit down counters- 1-CH 32-bit cascaded timer- Four programmable clock sources for each timer/counter
-
Product
RS232/422 Strobe Mux III Card & Panel
9565-32
-
32 serial port ISA compatible card connected by 4.8 ft (1.5m) cable and terminated as male DB25 connectors on external panel 14.5" high x 13" wide x 1" deep (645 x 330 x 25 mm).
-
Product
PCI Programmable Resistor Card 2-Channel 3 Ohm To 16.3k Ohm - SPST
50-294-131
Programmable Resistor Module
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
-
Product
Low Profile Front Panel For PCIe Remote Control Interface Card
53-921-LPF
Remote Control Interface
The 43-921 PCI Express-to-PXI Express expansion kit provides control of PXI Express modules installed in a PXI Express chassis using high bandwidth PCI Express technology. The extension kit can provide up to 4GB/s using PCIe Gen 2 x8 signaling. The 43-921 PCI Express-to-PXI Express expansion kit provides additional PXI instruments slots to the host computer by implementing a PCI Express-based control of PXI modules. The technology consists of a 53-921-001 host adapter installed in the host computer, a PCIe x8 cable, and a 43-921-00x, a remote controller with the 3U (Eurocard) expansion module. 53-921-001 comes in a PCI Express x8 footprint and equips with PCIe x8 cable connector.
