-
product
Probe Temperature Meter
Kusam Electrical Industries Limited
• Measurement Range : -50°C ~ 270°C; -58°F ~ 518°F• Resolution : 0.1°C (-50°C ~ 200°C) ; 1°C (200°C ~ 270°C)• Accuracy : -50°C ~ -20°C : ± (reading x 1.5% + 1°C), -20°C ~ 200°C : ± (reading x 1.0% + 1°C), 200°C ~ 270°C : ± (reading x 2.0% + 4°C)• Auto Power Off : 8min• Low Battery indication• °C / °F display selection
-
product
Dual Channel Peak Power Meter
8502A
The Spanawave/Giga-tronics 8502A Dual Channel Peak Power combine CW power measurement with the ability to make precise peak power measurements at any point on a pulsed waveform. This dual, built-in capability lets you make CW measurements and analyze pulsed waveforms with a single instrument.
-
product
CS | CSmicro Series Infrared Thermometer
Optris offers the industrial benchmark within affordable industrial pyrometers regarding the sensing heads’ size, robustness, and temperature rating. The different spectral options allow temperature measurements of plastics, metal, glass, and ceramics from -50-1030 °C with temperature resolution down to 25mK. Different optical options support a high distance-to-spot-size ratio to ensure an optimal focus on the target for high-temperature accuracy.
-
product
Motor Test for Stepping Motors
*Stable measurement: Since it uses Prony braking, this model provides stable measurement unaffected by moments of inertia and no coupling loss. In addition, the resulting measurements allow data correlation via the traditional double-balance method.*Precision measurement method: This model’s judgment of synchronization loss achieves high stability using algorithms developed by Sugawara Laboratories. Measurement mode can be chosen based on step angle. For pull-in torque, startup can be measured c...show more -
product
Bluetooth Enabled® Conductivity/TDS/Salinity/Temperature Pen
UltrapenX2™ PTBT1
Accuracy of ±1% of READING, ±0.2% at Calibration Point. KCl, NaCl and 442 Natural Water™ Modes. Automatic Temperature Compensation. Autoranging. Measurement Storage with Time, Date and Location. Export Stored Measurement Data Via Email. Proprietary Cell Design. Rugged Design with Aircraft Aluminum Body. Durable, Epoxy Encapsulated Electronics. Powered by One N Type Battery (Included). Waterproof.
-
product
Surge Voltage Generator
SSG 1500
BAUR Prüf- und Messtechnik GmbH
Cable fault location with the BAUR SSG 1500. Surge voltage generators are used for pre-location and pinpointing of high- and low-resistive as well as intermittent faults in power cables. The energy stored in a high-voltage capacitor is released at regular intervals or as DC voltage. The thus generated acoustic signal at the fault position can be recorded with a ground microphone and a universal receiver.* High surge voltage up to 32 kV* Continuously adjustable voltage* Voltage monitoring through kV meters with 3 measuring ranges* Automatic discharge unit
-
product
LV CT/PT
Shanghai Aoboor Electric Co., Ltd.
A CT lowers the current signals for measurement purposes, while a PT lowers high voltage values into lower ones. The transformers are designed to measure whether power systems are both accurate and safe.
-
product
Standard Current Transformers
Measurements International Ltd.
Single Range, Highest Permeability, Wide Measurement Range, Negligible Current Errors, High Accuracy.
-
product
RTD Measurement for VMEbus
VME390
The VME390 features 24 two, three or four wire high-accuracy PT100 measurement channels. Each channel has programmable alarm limits on which an interrupt can be issued.
-
product
ISO Viscosity Flow Cups
2353
The Elcometer 2353 ISO Viscosity Flow Cups are very easy to use instruments made of anodized aluminium with a stainless steel orifice, for measuring the consistency of paints, varnishes and similar products.
-
product
Clamp Meters
Kyoritsu Electrical Instruments Works, Ltd.
The clamp on the device is simply placed around a live wire. This allows one to measure the current on a wire without interrupting the operation of the electrical appliance. A clamp meter uses digital technology to bring instantaneous readings.
-
product
Nanoindenters
Nanomechanical testers from KLA Instruments™ provide precise, reliable and repeatable measurements of hardness, Young’s modulus, and other mechanical properties to help you explore new materials, reduce product failures and accelerate your time-to-market. We offer nanoindentation tools that range from easy-to-use to a high performance nanoindenter to the industry’s highest performance and most versatile nano tensile tester.
-
product
FD-11634, 8-Channel Sound and Vibration Input Device for FieldDAQ
786471-01
The FD-11634 can measure signals from integrated electronic piezoelectric (IEPE) and non-IEPE sensors such as accelerometers, tachometers, and proximity probes. The device also works with smart TEDS sensors, delivers a wide … dynamic range, and incorporates software-selectable AC/DC coupling and IEPE signal conditioning. The input channels simultaneously measure signals and have built-in anti-aliasing filters that adjust to your sample rate. This device is IP65/IP67-rated to be dust-tight and wa...show more -
product
Digital (1kV up) H.V. Insulation Tester
4103 IN (Ranges: 0.5kV, 1kV, 2.5kV, 5kV)
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Four insulation test voltages.● Insulation resistance; auto ranging on all ranges.● Measures insulation time test.● Bargraph indicates test voltage; rise and decay can be observed during tests.● Visual and audible warning if external voltage is present.● EnerSave™ feature to extend battery life.● 2 Lines × 16 characters large LCD.● Low battery consumption.● Low battery indicator.● Overload protection.● Auto-off.● Show test time duration (up to 99.9s) for easy comparison.● EEPROM calibration.
-
product
Ultraviolet Meter
UVR Series
UVR series is suitable to manage lamp of ultraviolet curing equipment, Also suitable to measure intensity of ultraviolet ray for sun light and lamp.
-
product
Flow Cell Kit
EQCMT
The two blocks of the EQCMT Flow cell are constructed using PEEK. It gives a high resistivity for chemical compounds.As well as QCM, these cell is reversible. With a inverted position of the blocks, it is possible to change from flow to static measurement.
-
product
Autocorrelator
PulseScout2
PulseScout2™ Optical Autocorrelators are a versatile, easy-to-use diagnostic tool for measuring ultrafast pulses from both high repetition rate (MHz) oscillators and low repetition rate (kHz) amplifiers from Visible to IR wavelength range.
-
product
Quantum Accelerometer
A quantum accelerometer uses atom interferometry to measure accelerations along a horizontal axis. Quantum accelerometers are able to achieve a combination of sensitivity and stability by exploiting quantum interference. As such, they will be critical components of a quantum inertial navigation unit, which will offer satellite-free navigation with unparalleled long-term accuracy. A phase locked SolsTiS system underpins this setup and provides the extremely low phase noise required to make high sensitivity measurements and dynamic frequency tunability to address multiple atomic transitions.
-
product
Lens Calibration
SpyderLENSCAL
A fast, reliable method of measuring and adjusting the focus performance on your camera and lens combinations.
-
product
Chloride Test System
C-CL-2000
The C-CL-2000 produces results on-site, within minutes that are accurate and comparable to expensive laboratory tests. It measures the electrochemical reaction of a weighted sample placed in an extraction liquid. It automatically shows a temperature compensated reading of percent of chlorides on its digital display. A wide range - from 0.002 to 2% chloride by weight - is covered.
-
product
BME680 Environmental Sensor
28061
Raise your project’s environmental awareness with the BME680. The Bosch Sensortec BME680 Integrated Environmental Unit combines a gas sensor with air pressure, humidity, and ambient air temperature sensing functions within a single package for high performance air quality measurement. Parallax Inc. places the BME680 on a compact PCB with a 6-pin male header. This capable sensor does not have to be difficult to use. The BME680 is supported by BlocklyProp visual programming as well as C libraries for the Propeller multicore microcontroller. Code for other controllers is available from the Bosch Github repository.
-
product
Optical Rackmount Systems
DiCon offers a variety of rack-mountable solutions for fiber optic switching, test automation, and wavelength management. With standardized or customizable options, our platforms can be easily configured to work in different environments. DiCon's systems feature low insertion loss, excellent reliability, and durability. Applications include fiber optic testing and measurement, fiber based sensing, optical network configuration and monitoring.
-
product
Sund Source
Qohm
The extreme low weight of 3.5 kg and small dimensions allow highly efficient measurements, saving time in transportation and test-set-up. This set prevents heavy lifting work and allows flexibility in positioning during tests, because also the tripod, power amplifier, and soft-bag are light weight.
-
product
Electronic Ballast High Frequency Parameters Tester
UI2002A
• Measure Vrms, Irms, W, PF/Hz • Voltage range: 10~600V, Current range: 10~2000mA, Frequency range: 20~70kHz • Accuracy: Class 2
-
product
0.50° Accuracy Full Attitude Surface Dynamic Motion Sensor
DMS-550
The DMS range of motion sensors is designed specifically for the motion measurement needs of the marine industry. Whether it is achieving IHO standard survey from any size of vessel, or providing safety critical monitoring of offshore platforms, large vessels, helicopter landing decks, cranes and positioning systems, the DMS provides accurate motion measurement in all sea conditions. Incorporating an enhanced external velocity and heading aiding algorithm for improved accuracy during dynamic manoeuvres, the solid state angular rate sensors offer reliability in the highest performing vertical reference units ever produced by TSS.
-
product
Micro Ohm Meter
TES Electrical Electronic Corp.
Best resolution. Accuracy 0.05%. 5A max test current. Manual or Auto Range. Measurement of resistive and inductive materials.
-
product
Micro Vickers Hardness Tester
Sinowon Innovation Metrology Manufacture Ltd.
◆ MicVision main use in testing materials allows for the measurement of the hardness of small or thin specimens and small areas of larger specimens, MicVision testing is commonly used to determine characteristics of thin sheets, foils, fine wire, epoxies, paints, etc. and is often employed in R&D applications .◆ MicrVision hardness is especially useful in determining hardness variations, caused by hardening, quenching, plating, fabrication, welding or annealing, bonding, etc. Micro hardness testing can be accurately employed using loads as slight as 10 gram, somewhat less and considerably more in certain situation.
-
product
Portable Oscilloscopes With Isolated Channels
Portable oscilloscope with 2 isolated channels, 600 V CAT III, 20 MHz bandwidth, 2 GS/s ETS, double 8,000-count multimeter with power measurements, 31-order harmonics with 40 to 450 Hz fund.,colour screen, USB.
-
product
Optics Test Systems
Electronic And Visual Autocollimators
Optik Elektronik Gerätetechnik GmbH
OEG GmbH specializes in the use of autocollimators, collimators and telescopes for special applications in optical measurement technology in the wavelength range from 380nm to 1550nm (SWIR).
-
product
Optical Spectrum Analyzer - MATRIQ
1000 Series
The OSA 1000 Series provides grating-based spectral test and measurement. It is an excellent fit for the testing of optical sources, amplifiers, transceivers and passive optical components.The OSA is available in a range of wavelengths for different applications, so you pay only for the capabilities you need.
