I²C
A slow Inter-Integrated Circuit bus protocol.
-
Product
Fanless Edge System With NVIDIA® JETSON™ TX2, 1 HDMI 2.0,2 GbE LANs And 1 USB 2.0
eBOX560-900-FL
-
The eBOX560-900-FL employs a NVIDIA Jetson™ TX2 module which has a powerful 64-bit ARM A57 processor; a 256 CUDA cores with NVIDIA® Pascal™ GPU Architecture; 8GB of LPDDR4 memory; and 802.11ac Wi-Fi with Bluetooth. It also supports NVIDIA JetPack 3.2 SDK including TensorRT, cuDNN, CUDA Toolkit, VisionWorks, GStreamer, and OpenCV, all built on top of L4T with LTS Linux kernel. The extremely compact system is your superb choices for AI, deep learning, and edge computing. Its tough construction is IP40-rated, and it has an extended operating temperature range of -30°C to +60°C (-22°F to +140°F) and up to 3G vibration endurance.
-
Product
Handheld Water Quality Meters
LAQUA DO210
-
Measures dissolved oxygen (DO) concentration in ppm (mg/L) and % saturation0.01 mg/L or 0.1% DO resolutionCompensates salinity, temperature, and atmospheric pressure Allows up to 2 calibration points using galvanic DO electrode°C & °F temperature readingsAuto log data; built-in memory can store up to 500 dataAuto stable, auto hold, and real-time measurement modesAuto shut-off (programmable: up to 30 minutes)Built-in electrode holder allows 2 electrodes to be attached Monochrome LCD with white LED backlight: 50 x 50 mmCasing is IP67 waterproof/dustproof, shock & scratch resistant, non-slipPowered by 2 x AA batteriesPackaged with galvanic electrode in carrying case3 years meter warranty
-
Product
Passive XMC-to-PCI Express Adapter
5934
-
The Technobox, Inc. P/N 5934 is designed to adapt a single-wide XMC card to a 4X PCI Express slot. The 5934 supports P15 only and allows access to PN4 signal via the adapter's DIN connector. The A and C rows of a 96-pin DIN connector connect with the 64-pin user I/O connector (J4/P4) on the mezzanine card, permitting internal connection of rear I/O.
-
Product
AC & DC DIELECTRIC STRENGTH TESTERS ( HIPOTS )
AV/DV-25VA-5
-
A C & DC DIELECTRIC STRENGTH TESTERS ( HIPOTS ).
-
Product
NI-9775 , ±10 V, Up to 20 MS/s/ch, 14-Bit, 4-Channel C Series Digitizer Module
784539-01
Digitizer
The NI-9775 provides referenced single-ended analog inputs with two timing modes for applications such as fault detection in electrical transmission lines or structural failure events. You can use the NI-9775 to measure finite samples up to 20 MS/s/ch to capture fault detections or to measure continuously at up to 4 MS/s. You also can use the built-in analog reference trigger to assist with high speed phenomena. Additionally, the NI-9775 supports waveform streaming at a lower sample rate.
-
Product
Current Mirrors
-
Analog Devices current mirrors are precision, high dynamic range, wide variable supply parts used for optical power monitoring, voltage biasing with current monitoring, and voltage-to-current conversion. Our current mirrors can monitor current down to as little as 3 nA and as much as 3 mA, with a linearity of 1% or better. The current dynamic range is 120 dB or 6 decades of current range, while the overcurrent protection feature in our devices forces the input pin to ground to avoid part damage. Over temperature (–40°C to +85°C) and process, the dynamic range only suffers 10 dB at the lower end of the range.
-
Product
Weighing Rain Gauge
HD2016
-
Weighing rain gauge, area 400 cm². 3000 cc collecting reservoir. Automatic water discharge. Operating temperature from -20 °C (with heater option) to +70 °C.
-
Product
Cable Assembly, 50-Pin D-Type, Male to Male, 0.5m HV, Exit Towards Pin 1
A050DM5-050DM5-HA050
Cable Assembly
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assemblies can be secured to the mating part by a screwlock.
-
Product
Explosion-Proof Differential Pressure Switch
1950G
-
The Model 1950G Explosion-Proof Switch combines the best features of the popular Dwyer Series 1950 Pressure Switch with the benefit of natural gas compatibility. Units are rain-tight for outdoor installations, and are UL listed for use in Class I, Groups A, B, C, & D; Class II, Groups E, F, & G and Class III atmospheres, ATEX for EExd IIB & Hydrogen T6, and CSA & FM approved for Class I, Div. 1, Groups B, C, D; Class II, Div. 1, Groups E, F, G and Class III atmospheres
-
Product
Immersion Probe For Liquids
DPT-24
-
DPT-24 Immersion Probe for Liquids - 24'' #304 stainless steel welded shaft. Wooden Handle. Diameter is .3/16'' diameter. Immersible. Maximum temperature 350°C, Time constant 2 Seconds. 5 foot lead. Not isolated.
-
Product
NI-9477, 60 V, 32-Channel (Sinking Output), 8 µs C Series Digital Module
779517-01
Digital Module
60 V, 32-Channel (Sinking Output), 8 µs C Series Digital Module - The NI‑9477 works with industrial logic levels and signals to connect directly to a wide array of industrial relays, solenoids, and motors. Each channel is compatible with signals from 5 V to 60 V and … features isolation from channel‑to‑earth ground. You can wire the NI‑9477 channels in parallel to sink up to 20 A of current per module (1 A per channel maximum).
-
Product
pH 700 Benchtop pH Meter
-
The easy-to-use, microprocessor-based pH 700 benchtop meter measures pH, mV, relative mV, and temperature. The large, dual-display LCD provides excellent visibility—even from a distance. Automatic temperature compensation (ATC) maintains reading accuracy even with fluctuating temperatures. Five-point pH calibration, with automatic buffer recognition for both USA (pH 1.68, 4.01, 7.00, 10.01, 12.45) and NIST (pH 1.68, 4.01, 6.86, 9.18, 12.45) pH buffers, makes for easy calibration no matter which requirement you need to meet. Meter features HOLD, ATC, selectable °F or °C measurement, recall of electrode slopand offset, and electrode diagnostics. The convenient pull-out quick reference card keeps procedures handy at all times. Meter accepts any pH or ORP electrodes with a BNC connector.
-
Product
Withstanding Voltage/Insulation Tester
-
AllWin Instrument Science and Technology Co., Ltd.
W to I, I to W automatic conversionVFD display
-
Product
Omnidirectional Hotwire Probe
AP3203F
-
Omnidirectional hotwire probe for cold environment. Measuring range: air speed 0.02 ÷ 5 m/s, temperature -30 ÷ +30 °C.
-
Product
NI-9485 , 8-Channel, SSR Relay, 60 VDC/30 Vrms, 750 mA C Series Relay Output Module
779600-01
Relay Output Module
The NI-9485 allows for direct connection to a wide array of industrial devices such as motors, actuators, and DC devices. Each channel provides access to a solid state relay (SSR) for switching voltages up to 60 VDC/30 Vrms with switching current up to 750 mA per channel or up to 1.2 A on four channels. Each channel also features channel-to-channel isolation.
-
Product
AdvintRIO™ Reconfigurable I/O
PIRANHA
-
The Piranha platform employs a NI single board RIO (sbRIO), NI C Series I/O modules, and custom circuitry. Piranha systems are not dependent on a separate host computer. They offer both Ethernet, and Wi-Fi connectivity to a powerful real-time controller and high performance field-programmable gate array (FPGA) and up to two (2) C Series I/O modules. It provides stand-alone embedded execution for deterministic LabVIEW Real-Time applications. These controllers are designed for ruggedness, reliability, and low power consumption. The heart of Piranha system is the reconfigurable I/O (RIO) FPGA core. The RIO core has an individual connection to each I/O module and is programmed using easy to use elemental I/O functions to read or write signal information from each module. Multiple units can also be daisy changed together for larger applications.
-
Product
RTD Measurement for PCI
PCI390
-
The PCI390 features six 2-, 3-, or 4-wire high-accuracy RTD measurement channels. Each channel has programmable alarm limits on which an interrupt can be issued. The local DSP (TMS320C203) performs linearization, auto-calibration and alarm-limit checking. Sensor-data is available in °C, °F, K and Ohms. All inputs are optically isolated from the system.
-
Product
AC/DC Power Supply 60 W
TR100M150
-
AC/DC power supply with 100 W from Cincon | input ranges 90 - 264 VAC | output 15 V | operates in temperature from -20 to +80 °C | provides 2 MOPP
-
Product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type C, Ø1.50mm, 155gf
K100-C150155-SKAU
Spring Probe
K100 Series, Pitch 100mil, Tip Style C, Tip Diameter Ø1.50mm, Spring force 155gf, Steel with Gold Plating.
-
Product
NI-9871, 4-Port, RS485/RS422 C Series Serial Interface Module
779892-02
Serial Interface
The NI‑9871 adds RS485/RS422 serial ports to CompactRIO systems. The serial ports are accessed directly from the FPGA to offer you flexibility in communicating with serial devices. The module has individual buffers on every port that save FPGA space and simplify programming. The NI‑9871 supports standard start bit, stop bit, and handshaking settings. It uses an external power to provide maximum compatibility and reliability under all serial port conditions.
-
Product
Sensor Six-Pack
PT-6
-
PT-6 Sensor Six-Pack - For multi-point temperature measurements. Inexpensive, Flexible. Welded sensor beads, tough kapton insulation. Diameter is .029''. Maximum temperature 350°C, Time constant 0.01 Seconds. 5 foot lead. Not isolated.
-
Product
Military & Aerospace EMC Testing
-
EMC Technologies’ Melbourne and Sydney and also EMC Bayswater (south-east Melbourne) laboratories provide NATA accredited Electromagnetic Compatibility (EMC) MIL-STD testing of military equipment to MIL-STD 461 B, C, D, E, F & G. The scope includes most test requirements and methods called up by MIL-STD 461/2, allowing defence agencies, contractors and defence suppliers to prove compliance with the stringent EMC limits imposed on defence equipment and systems.
-
Product
32-CH Sourcing Type Digital Ouput EtherCAT Module
EPS-2032
-
*32-CH sourcing type digital output*Quick removable European type connector*Slave module healthy monitoring*Wide operation temperature range*: -20°C - 60°CCompact size: 100 (L) x 100 (H) mm
-
Product
ARINC 429 Test & Simulation Interface for VME
VME-429
-
Avionics Interface Technologies
4, 8, 16, 32, or 64 Software Programmable Tx/Rx Channels - Programmable High/Low Speed Operation - Concurrent operation of all Tx/Rx Channels at high data rates - Full Error Injection & Detection - Rate-oriented Label Transmission - Label Selective Trigger for Capture/Filtering - IRIG-B Time Code Encoder/Decoder for Data Correlation - ANSI Application interface supporting C, C++, C#, and .net development - Device driver support: Windows, Linux, & VxWorks (others on request) - Designed for extended temperature operations - 64-bit VME - Interface (VME master & slave capability) - Front Panel and Rear I/O (P2) Available
-
Product
Freezer Rooms
-
Our walk-in cold rooms offer reliable, efficient environmental controls for a variety of applications; including: GMP Storage and Cold Storage for Seed and Agricultural Products, Nutritional Supplements, and more. Our cold rooms are typically supplied with desiccant or refrigeration based dehumidification in order to maintain a low dew-point and prevent ice accumulation on both product and equipment surfaces. Typical temperatures for our cold rooms range from of 0o C to 10o C.
-
Product
Cable Assembly, 9-Pin D-Type Female to Unterminated With Cut Ends, 1m, HV
A009DF4-C-HA100
Cable Assembly
A range of 9-Pin D-Type High Voltage cable assemblies with unterminated connections on one end, constructed from PTFE Type C insulated wire. The unterminated connections are coded to match the connector pin designation.
-
Product
2MP HDR Jetson TX2/TX1 Camera Board
E-CAM20_CUTX2
-
e-CAM20_CUTX2 is a 2MP HDR camera board for NVIDIA® Jetson TX2 /TX1 developer kit. It has an ability to stream seamlessly at wide temperature range (-40°C to 85°C). It enables an excellent low-light performance and can capture images even under 0.5 lux. e-CAM20_CUTX2 is based on 1/2.7" AR0230AT CMOS image sensor from ON Semiconductor™. It has S-mount (M12) lens holder which allows customers to choose and use the lens according to their requirement.
-
Product
Cable Assy 9-Pin D-Type, F/F, 2m, HV
40-970-009-2m-FFHV
Cable Assembly
A 9-Pin D-Type Cable Assemby for general use constructed from PTFE Type C insulated wire. The connector assembly can be secured to the product by screwlocks.
-
Product
IQ Demodulator
-
Teledyne RF & Microwave IQ Demodulators are fully space-qualified designs providing stringent phase and amplitude matching, and superior output third order intercept performance. To meet high LO and IF rejection requirements diplexers are used at the I and Q ports. All components and processing fully meet MIL-PRF-38534, Class K and MIL-DTL-28837. Teledyne RF & Microwave can provide performance to meet most receiver system requirements, including single or moving LO frequencies and tight phase and amplitude matching. Customers can specify our designs for space, military, or commercial applications.
-
Product
NI-9201, ±10 V, 500 kS/s, 12-Bit, 8-Channel C Series Voltage Input Module
783730-01
Voltage Input Module
±10 V, 500 kS/s, 12-Bit, 8-Channel C Series Voltage Input Module - The NI‑9201 is an effective combination of channel count and speed at a low price for an economical multifunction system. The module features up to 100 V of overvoltage protection for errant signal connection or unexpected signals to the individual channels.
