PXI Systems Alliance
promotes and maintains the PXI standard.
-
-
product
Vibration Transducers Calibration System
The system is used for calibration of vibration transducers as well as:*ICP and charge accelerometers;*piezoelectrical and capacitive vibration transducers;*vibration-measuring instruments.
-
product
Bench-top Microreactor & Combined Mass Spectrometer System
CATLAB-PCS
The Hiden CATLAB is a bench-top microreactor and combined mass spectrometer system for rapid and reproducible catalyst characterisation and reaction studies. The modular benchtop system features an advanced fast-response low thermal mass 1000oC furnace, multistream gas flow control of up to eight integrated gas streams, together with the precision Hiden quadrupole gas analyser.
-
product
Housing with Acquisition System for Weather Stations
HD32.35
HD32MT.1 data logger integrated in an AISI 304 stainless steel outdoor housing. Screen to protect the housing from solar radiation. Powder-coated white.
-
product
Metal Detection Pipeline System for Vacuum Fillers
HDS
Metal detection systems for sausage manufacture and inspection of high viscosity liquids. The maximum capacity to detect all metal contaminants combined with stable on-line performance. Full stainless steel construction and sealing standards up to IP69K make HDS pipeline detectors suitable for the harshest meat processing environments.
-
product
Sensor Signal Conditioning System
SCS
SCS Sensor Signal-Conditioning System complements the iDSC 1816 anti-aliasing board to provide a continuous path in a single package: starting with raw measurements at the sensor and ending with conditioned anti-aliased data logged to disk on a PC.
-
product
PXI 2A Multiplexer, 1-Bank, 128-Channel 1-Pole
40-614-015
The 40-614 High Density 2 Amp multiplexer module is available in 20 configurations. All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 200VDC/140VACThe module is suitable for signal routing in ATE and data acquisition systems. User connections are made via a front panel 160-pin DIN 41612 connector which is fully supported by our range of cabling and connector solutions.
-
product
CPCI or PXI DPFS Board
MS 1830
- Configurable Frequency Ranges from 100Hz to 1MHz- Resolution insteps of 0.03Hz- Duty Cycle 50%- Amplitude of the Digital Frequency out : Low – 0.4V max, High – 4.8V min- Rise/Fall Time (for a 15pF Load) is typically 5 ns- Amplitude of the Analog waveform out : Low – 0.4V max, High – 4.8V min- Sinusoidal or Square Wave Output (Configurable)- Differential / Single Ended Output (Configurable)- Frequency on each of the 8 Channels are individually Programmable- Hot Swap Facility for live insertion and removal of the board- Facia plate with Micro Switch Assembly, provided for proper insertion / easy removal of the Board- BNC Connector Interface for Signal Output at the front panel- Each Output Channel is driven by a Cable Driver to drive 8m of Coaxial Cable- Driver interface for Windows XP/VISTA/7 and LINUX OS
-
product
Instrument Transformer Test Systems
Our systems for testing voltage (VT) and current (CT) instrument transformers are conceived among other things for testing accuracy and insulation.
-
product
Cable Fault Location System
Syscompact 2000 M Pro
BAUR Prüf- und Messtechnik GmbH
Cable fault location system 2000 M pro. The portable BAUR Syscompact 2000 M pro cable fault location system is used for cable fault location and cable testing in low- and medium-voltage cables up to 65 km length.* Fully integrated proven cable fault pre-location methods* Surge mode for acoustic pin-pointing* Easily transportable* Ideal for locations that are difficult to access
-
product
Automated Front & Backside Mask Aligner System
Model 6000
With over 4 decades of manufacturing in the semiconductor industry, OAI meets the growing challenge of a dynamic market with an elite class of production photolithography equipment. Built on the proven OAI modular platform, the Model 6000 has front and backside alignment that is fully automated with a submicron printing capability as well as submicron top to bottom front side alignment accuracy which delivers performance that is unmatched at any price. Choose either topside or optional backside alignment which uses OAI’s customized advanced recognition pattern software. These Mask Aligners have OAI’s Advanced Beam Optics with better than ±3% uniformity and a throughput of 200 wafers per hour in first mask mode, which results in higher yields. The Series 6000 can handle a wide variety of wafers from thick and bonded substrates (up to 7000 microns), warped wafers (up to 7 mm-10mm), thin substrates (down to 100 micron thick), and thick photo resist.
-
product
Automated Pressure Calibration System
4322
The Fluke Calibration 4322 Automated Pressure Calibration System enables almost any user to calibrate almost any pressure gauge, transducer, transmitter or switch, including vacuum, compound, absolute and high-pressure devices. It provides high-end, laboratory-grade performance across a very wide range, on the bench or in situ.
-
product
LED, Micro LED And VCSEL Measurement Systems
With a track record spanning decades, Gamma Scientific is a leading provider of custom, high-precision light measurement solutions for LED, micro LED, and luminaires in both the laboratory and production environment. The combination of our extensive competencies and commercial expertise has led to the development of a range of modular test solutions that can be readily integrated within the various phases of light source development and manufacturing. Each of these test modules includes measurement instrumentation, a system controller, all peripheral components, and top-level software interfaces.
-
product
Telemetry System for Electrics
HTS-SS Blue
Our HTS-SS Blue sensor station system provides comprehensive telemetry information about your electric-powered aircraft and is compatible with the HTS-Volt, HTS-GPS, HTS-TEMP, HTS-ORPM, HTS-MRPM, HTS-C200 and HTS-C50 suite of sensors.
-
product
RF/Microwave ATE Systems
Over two decades ago, In-Phase Technologies founded our company for the purpose of designing and producing reliable high quality RF and microwave Automated Test Equipment (ATE). We continue that tradition today, providing the best, world-class automated test equipment. Our system designs bring together the right combination of Commercial Off the Shelf (COTS) test equipment, custom designed and built Interface Test Adapters (ITAs), lightning fast and accurate measurement software, and the optimum user interface to make all of this technology easy to use.
-
product
GPS-Aided Inertial Navigation Systems
INS
The INS was unveiled in 2001 when Inertial Labs started manufacturing its first MEMS-based, IP67 and IP68 sealed and OEM versions, MIL-STD-810G qualified multiple interfaces and COM ports Single and Dual Antenna GPS-Aided Inertial Navigation Systems (INS). Each INS contains an Inertial Labs developed Tactical or Industrial-grade Inertial Measurement Units (IMU) and reliable single or dual GNSS receivers from suppliers like NovAtel, u-blox and Septentrio.
-
product
Small Drop Test System
KRD41 series
KRD41 series small drop tester is suitable for free-fall test of small consumer electronics and components such as mobile phones, walkie-talkies, electronic dictionaries, CD / MD / MP3 and so on, applicable standards JISC 0044 and IEC 60068-2-32. Through standard tests on electronic products (surface drop, corner drop, edge drop, etc.) and collecting data, it simulates the vertical drop impact of electronic products during transportation and handling. It provides a basis for the design of the product's buffer and vibration damping and the selection of structural materials.
-
product
CM AXIe-0 system module
CM AXIe-0 MODULE
CM AXIe-0, made in the AXIe standard, is designed to work as part of measuring systems created on the basis of the AXIe-0 backbone. CM AXIe-0 is intended for use as part of AXIe-0 standard crates with the number of seats (slots) not more than 14. CM AXIe-0 complies with the requirements of the AXIe-0 standard for system modules of the AXIe-0 bus.
-
product
X-ray and CT inspection System
UX20
Due to the transformation to electric mobility, foundries are increasingly producing larger and more complex components. With its exceptional inspection envelope and the smart Geminy software, the UX20 facilitates fast and precise inspections of cast parts and helps increase overall production efficiency.
-
product
Measurement Microphone System
MK224SYS
The MK224SYS Type 1 measurement microphone system offers a cost effective option to acoustic measurements. Perfomance: 8 Hz to 18 kHz response, 50 mV/Pa sensitivity and a "A" weighted noise floor less than 14 dBA.
-
product
Electric Vehicle Module Test System
FTV
Drive simulations with standard Electric Vehicle tests: FUDS, SFUDS, GSFUDS, DST and ECE-15LBattery Module TestingStart/Stop TestingTraction Battery TestingSupercapacitor / Ultracapacitor TestingDrive Cycle Testing
-
product
ASYMTEK Select Coat Conformal Coating System
SL-940
Reliability is what we do best. We’ve combined our robust and flexible SL-940 system features into standard Trim Packages with Essential Option Bundles to simplify equipment selection, providing automation, process control, traceability, consistency, and changeover efficiencies that drive exceptional conformal coating outcomes. When you choose a standard trim package, you’ll get the conformal coating capabilities you need with minimal lead time.
-
product
Temperature Calibration System
Thermal Engineering Associates, Inc.
Systems for determining relationship between temperature-sensing junction voltage versus junction temperature of diodes, integrated circuits and thermal test die. Provides internal current sources, voltage measurement to 1 mV, and temperature measurement to 0.1ºC. 16-channel capability with optional printer and serial port data output.
-
product
Low-Density PXI Switch Matrix Modules
Our low-density PXI switch matrix modules are a cost-effective solution for applications that require relatively small matrices in the PXI format. These low-density switch matrices can be expanded by connecting together multiple modules, however, we recommend that users look at the higher density switch matrix modules that involve less user configuration. Reed relay versions use high quality sputtered ruthenium relays that exhibit excellent contact performance under low and medium level switching conditions. For general purpose applications that also require higher power handling, the range of electro-mechanical relays provides an ideal solution.
-
product
Discrete Device Test System
capability to perform parallel testing of power discrete devices. As the standard specifications of mainframe, 341-TT/P has 1.2kV/20A and 351-TT/P has 2kV/50A capabilities. These systems have 2 testing subsystems, each of which has 4-station capability by multiplexing to 4 handler/prober stations for high volume production testing.
-
product
SpaceWire PXI Mk2
The SpaceWire PXI Mk2 card is a versatile SpaceWire Interface, Router or RMAP Target device. The card is designed to be an efficient host interface to a SpaceWire system or network, by utilising a cPCI or PXI backplane.
-
product
E-Band Network Analyzer Systems
Keysight offers convenient and affordable solution bundles for millimeter-wave measurements in the E-band frequency range. Bundle configurations use Keysight PXI or Streamline vector network analyzers (VNAs), software, and Virginia Diodes, Inc. (VDI) frequency extenders.
-
product
Hydrogen Leak Detection System
Yamaha Fine Technologies Co., Ltd.
Yamaha Fine Tech's proprietary MEMS hydrogen sensor equipped, and a wide range of concentrations, from low to high concentrations, detectable just with one unit.A high resolution hydrogen leak detector that can detect low to high concentrations in the range from 0.5 ppm to 13,000 ppm with a single unit. Quick measurement is realized by high-speed response and real measurement. A desktop type and a handy type are available.
-
product
ThermalAir Desktop Series Temperature Forcing System
ThermalAir TA-1000A Desktop System
The ThermalAir TA-1000 high capacity thermal air stream system is used for temperature testing, fast thermal cycling, and device temperature characterization of components, hybrids, modules, PCBs, and other electronic and non-electronic assemblies at precise temperature from -25°C to +200°C.
-
product
Reactor Loss Measurement Systems
Measurements International Ltd.
The AccuLoss® SR2020 System by Measurements International emerges as a premium, dependable solution tailored for measuring losses in high-voltage shunt reactors. Specifically engineered to function seamlessly at remarkably low power factors, this system excels in applications demanding extensive scalability. Notably, the AccuLoss® SR2020 System offers two key advantages: unparalleled accuracy and remarkable speed.
