Standards
A controlled reference or acknowledged technical criterion.
See Also: IEC, IEEE, Mil, Interoperability Test, Compliance
-
Product
Standard 1.08 (31.00) - 3.50 (99.00) General Purpose Probe
EPA-2X
General Purpose Probe
Current Rating (Amps): 5Average Probe Resistance (mOhm): 35Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 160Full Travel (mm): 4.06Recommended Travel (mil): 107Recommended Travel (mm): 2.72Mechanical Life (no of cyles): 2,000,000Overall Length (mil): 970Overall Length (mm): 24.64
-
Product
WinSRS Software
-
The GHI Windows version of our powerful SRS module has been made even more powerful by the addition of new processing modes. These include: 1. Statistical SRS - This mode provides MEAN and Positive STANDARD DEVIATION plots which can be used when tailoring shock specifications based on environmental measurements. 2. Max-I-Max Envelope SRS - This module plots succeeding SRS's on one screen while at the same time plotting an 'envelope' that bounds all SRS's processed. 3. Overlay Plot - This mode allows overlaying plots of multiple SRS's. The user may plot Positive and Negative Max-I-Max spectra on the same screen. The foregoing are in addition to our traditional features
-
Product
Chemiluminescence NO/NO2/NOX Analyzer
Model T200
-
Teledyne Advanced Pollution Instrumentation
The Model T200 NO/NO2/NOx analyzer uses the proven chemiluminescence detection principle, coupled with state-of-the-art electronics to allow accurate and dependable low level measurements for use as an ambient analyzer or dilution CEMS monitor.A unique AutoZero feature provides superb stability by continuously correcting for zero drift, while advanced Adaptive Filtering allows the analyzer to optimize performance under changing conditions. The Model T200 includes a permeation inlet dryer for ozone generation to provide excellent reliability with no periodic replacement required. A catalytic exhaust ozone scrubber is standard for maximum safety and pump life.
-
Product
Faraday Cages
-
LBA's EMFaraCage® faraday cages are EMI and RFI shielding boxes and RF test enclosures that bring convenience to device testing. Faraday cages are ideal for isolating critical systems in high field RF environments or wherever RF ingress or egress must be minimized. Security, production testing, biomedical research and semiconductor testing are only a few of the many areas where EMFaraCage® faraday shielded enclosures are employed. EMFaraCage® faraday cage enclosure systems are fully featured to support a wide variety of test missions. The standard faraday cages include effective power, dataline and RF signal isolation in large test volumes. EMFaraCage® faraday cages are much more affordable than shielded room solutions and offer the convenience of portability.
-
Product
Pocket HD
-
The NEXIQ Pocket Heavy Duty handheld scan tool provides immediate access to critical diagnostic information. Pocket HD comes loaded with both Heavy Duty Standard (HDS) and Light and Medium Truck 2016 (LMT). The ability to run special tests not included.
-
Product
PXI-8432/ 4-Port, Isolated, RS232 PXI Serial Interface Module
779538-01
Serial Interface
4-Port, Isolated, RS232 PXI Serial Interface Module - The PXI‑8432/4 is a high-performance interface for high-speed, port‑to‑port isolated communication with RS232 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
Fume Hood Monitor
FHM10
-
Fume hoods are a primary source or protection in laboratories. Face velocity measurements are often used to gauge the performance of a fume hood’s ability to contain and exhaust hazardous chemicals. By accurately measuring face velocity and alarming on unsafe conditions, TSI’s FHM10 Fume Hood Monitors provide a high level of fume hood safety. And, the FHM10 helps users comply with standards and regulations set forth by OSHA, NFPA, ANSI Z9.5, and SEFA, calling for monitors to be installed on fume hoods.
-
Product
Wiring Tester
WIZE
-
The testers can be used both in production and maintenance, as WIZE® is suitable for simple wiring tests and complex interconnect tests for full systems. WIZE®’s specifications make it compatible with the standard requirements used for testing in the aeronautics, space, rail and defence sectors or any other industry using wiring.
-
Product
OnyxFX FlexorSet 4-Ch. 250 MHz A/D w/DDCs, 2-Ch. 800 MHz D/A w/DUC, Int - 3U VPX
Model 5973-313
-
- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- Four 250 MHz 16-bit A/Ds- Four multiband DDCs- One digital upconverter- Two 800 MHz 16-bit D/As- Extended Interpolation- Sample clock synchronization to an external system reference- PCI Express (Gen. 1, 2 and 3) interface up to x8- User-configurable gigabit serial interface- Optional optical Interface for backplane gigabit serial interboard communication- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Compatible with several VITA standards including: VITA-46, VITA-48 AND VITA-66.4 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- See comparable JadeFX Xilinx Kintex UltraScale FPGA Family:- Model 5983 JadeFX Kintex UltraScale Processor and FMC Carrier 3U VPX- Model 5983-313 JadeFX FlexorSet 4-Ch. 250 MHz A/D w/DDCs, 2-Ch. 800 MHz D/A w/DUC, Int - 3U VPX
-
Product
Noise Dose Meters
-
Here you will find a full range with an industrial standard noise dose meter to suit every requirement. With the portable noise dose meter you can carry out measurements quickly to gain control of a situation or to set the device to take timed measurements. The noise dose meter is important for all industries, especially by using it as a mobile device which is able to assess office stress levels or street noise levels.Often problems arise from noisy neighbors or if bars and restaurants are in residential areas and produce noise levels after 10pm in excess of what local laws permit. We, of course, can assess which noise dose meter you require in relation to the issue you have and the relating laws. We also have microphone extension cords, tripods, calibrators and calibration certificates for most models of noise dose meter.
-
Product
Additional Products: Standard Voltage 50 Pin D-Type Cables - Connector to Connector
-
The connector to connector cable assemblies below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
Product
JUMPACKS
-
Designed to jump start large V8 gasoline and diesel engines, its compliant with the Safety Standard and will keep you going in all-weather conditions.
-
Product
Synchro to Digital-Resolver to Digital Converters
SDC-F-RDC-F
Digital / Synchro Converter
Computer Conversions Corporation
SDC/RDC-F Series are Industry Standard Tracking Synchro and Resolver to Digital Converter modules with programmable resolution, 8/16 Bit data bus controls, continuous Built-In Self-Test report, and forced angle test modes used for functional validations on command.
-
Product
Widely Tunable Ultrafast Laser System For Multiphoton Imaging
InSight X3
-
Spectra-Physics’ new InSight® X3™ is the third generation of Spectra-Physics’ industry leading InSight platform, specifically designed for advanced multiphoton microscopy applications. Based on patented technology1, InSight X3 features a broad 680 nm to 1300 nm continuous, gap free tuning from a single source, nearly double the tuning range of legacy Ti:Sapphire ultrafast lasers. InSight X3 delivers high average and peak power levels across the tuning range, including critical near infrared wavelengths above 900 nm for deepest penetration in-vivo. With Spectra-Physics’ integrated patented DeepSee™, the industry standard dispersion pre-compensator, the short pulses are optimally delivered through a microscope to the sample for maximum fluorescence and penetration depth. InSight X3 also has exceptional beam pointing stability, beam quality and output power stability, as well as fast wavelength tuning, making it ideal for microscopy.
-
Product
Infiniium S-Series High-Definition Oscilloscope: 500 MHz, 4 Analog Channels
DSOS054A
Oscilloscope
500 MHz bandwidth (upgradable)4 analog channels Capture a longer signal trace with 20 GSa/s maximum sample rate and 100 Mpts/channel of standard memory Get superior signal integrity with system ENOB of 8.1 bits and 10-bit analog-to-digital converter (ADC)Gain increased usability with the multi-touch supported 15 inch capacitive touch screen and standard solid state drive for fast boot and high reliability Access a wide range of protocol, compliance, and analysis software
-
Product
Standard 1.10 (31.00) - 3.85 (109.00) Battery Probe
BIP-2
Battery Probe
Current Rating (Amps): 5Average Probe Resistance (mOhm): 30Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 50Full Travel (mm): 1.27Recommended Travel (mil): 50Recommended Travel (mm): 1.27Mechanical Life (no of cyles): 1,000,000Overall Length (mil): 365Overall Length (mm): 9.27
-
Product
S bus Extender
Arcareach Sigma
-
Arcareach | Sigma is an inverse NT-1 that changes an S interface (NT side) into a U interface (LT side) and provides power feeding (70V) on the U interface. Many digital PBXs offer ISDN S-bus interfaces as standard which can operate up to 0.9km (3000ft) under certain conditions. When there is a requirement for the S-bus to be located much further from the PBX the Arcareach | Sigma can be used to turn the S-bus interface into a U interface, supporting 2B1Q encoding.
-
Product
Modules
1x9 BIDI Transceiver Modules
-
The module supplies best solution of short-haul 20 km for fiber optical system and link distance. The module with the Differential PECL of 3.3 or 5 Voltage and provide the system designer with products to implement a range of ATM (Asynchronous Transfer Mode) and SONET for Telecommunication. The module was all supplied in the new industry standard 1x9 SIP package style with a Bi-directional BIDI SC ST or FC connector interface.
-
Product
Capacitance Standard
GenRad 1417
-
The GenRad 1417 Four-Terminal Capacitance Standard consists of a 1 F standard capacitor and two precise inductive voltage dividers used to scale the value of the 1 F capacitor up to 1 F in decade steps. This arrangement provides accuracy and stability unattainable with very high-value true capacitors.
-
Product
Mass Flow Controller for Medium Flow
HFM-205 / HFC-207
-
The HFM-205/HFC-207, Teledyne Hastings' flexible, general purpose series of mass flow meters and controllers accurately measure and control mass flow in a variety of applications. Featuring reliability and stability, the 200 Series is chosen for its very stable performance with varying ambient conditions. A wide choice of elastomer seals make this flow controller compatible with most gases.The HFM-205 / HFC-207 meters and controllers have flow ranges from 0-1000 slm to flows of 0-2500 slm; provide analog outputs, are constructed of stainless steel and can be configured with normally open or normally closed valves. The full scale range is specified by the end user. A NIST traceable calibration certificate is standard. With a full complement of fitting and elastomer options, the HFM-205/ HFC-207 covers a wide range of high flow applications.
-
Product
PXI And PXIe Chassis
-
PXI chassis and PXI Express (PXIe) chassis available in 8 to 19 slots and different performance characteristics. These chassis are fully compliant with PXI standards and can house any vendor’s modules. Our Gen 3 PXIe chassis offers full hybrid capability on all peripheral slots, giving you the flexibility needed to choose whichever PXI or PXIe products best fit your applications.
-
Product
QuadraPaddle 90 Series Modules
-
The versatility of VPC's QuadraPaddle twin female contacts provide four beams per end to ensure signal integrity from instrumentation to the Unit Under Test (UUT).Twin male contacts interconnect to ribbon cable, headers, and other standard connectors.Makes system configuration a simple “plug & play” operation and delivers high density, high performance interconnectivity at a lower cost per point.
-
Product
EtherCAT Slave System
EPS Series
-
The ADLINK complete EtherCAT solution, from hardware to middleware to software, with every element tailored for dedicated EtherCAT functionality, includes PCIe-833X Series master controllers, EPS slave systems, and remote monitoring and control providers. As well, ADLINK’s Softmotion one-stop control kernel delivers flexible and easy-to-use intelligent platforms for driving next-generation modern Smart Factories. ADLINK's EPS slave system brings the power the flexibility to EtherCAT environments. State-of-the-art modular construction allows the EtherCAT slave to be configured to fulfill the needs of both small local applications and expansive distributed platforms. The EPS system with comprehensive and high-density I/O modules that include DI/O, pulse-chain motion modules. Leveraging ARM and FPGA technologies, the EPS slave is able to monitor and report system integrity via EtherCAT communication, while relay module lifecycle and signal integrity of analog output are monitored cyclically, and hot swappability reduces downtime significantly. Uniquely designed for full operability in conditions from -20°C to 60°C,the EPS slave system is also fully compliant with the EN 60068-2 standard for shock and vibration and EN 61000-6 for heavy industrial EMC protection, as well as emission certification. Corresponding ESI files for each EPS system can be generated thru ADLINK's Windows-based EtherCAT slave utility, LinkMasterPro™.
-
Product
Insect Rearing Rooms
-
Standard walk-in incubators or coolers used in the rearing of drosophila and other biological organisms often end up being problematic for a number of reasons. The acids inherent in the rearing of many specimens or their food can quickly corrode a standard refrigeration evaporator. High humidity exacerbates the issue, as droplets of concentrated acid will collect on the cooling components.
-
Product
Small Engine AC Motoring Dynamometers
-
SAKOR Technologies developed its new Small Engine AC Motoring Dynamometer specifically to meet the needs of engine manufacturers who must now comply with engine testing procedures required by new emission standards contained in 40 CFR Part 1065. These new requirements apply to almost every kind of small internal engine, including those in handheld power tools and lawn and garden tools.
-
Product
TRMS AC/DC Clamp-on Power
HT9023
-
HT9023 has been designed to measure AC, DC AC+DC current up to 1000A in TRMS reaching CAT IV 600V and CAT III 1000V in compliance with safety standard IEC/EN61010-1. The clamp also measures DC voltage up to 1500V, AC, AC+DC voltage up to 1000V, Active, Reactive and Apparent Power, Power Factor, Energy, voltage/current harmonic analysis up to the 25th with THD% calculation in balanced single-phase or three-phase systems.
-
Product
SMA Patch Cords
FY8
-
SMA patch cord, The standard fiber optic cable assemblies, with simplex, duplex patch cords and standard pigtails.
-
Product
7-Slot 3U OpenVPX Backplane Aligned To SOSA | 6 VITA 65 Slots + 1 VITA 62 PSU Slot
1SVX306AXX-XX31
-
These six VITA 65 slots plus one VITA 62 slot (6+1) backplanes are designed in alignment with The Open Group® Sensor Open Systems Architecture™ Technical Reference Standard, or SOSA®.
-
Product
3.5-inch Embedded Board
-
The 3.5" embedded board is created in an architecture of low power consumption with reliability required for various applications in rugged environments. The ZIO form factor is an integrated interface standard defined by Axiomtek and has been adopted as one of our specifications in our 3.5" embedded single board computers to meet concerns regarding insufficient expansion interfaces in small form factor (SFF) single board computers.
-
Product
QAble Next-Gen Testing
-
QAble applies purpose-built testing methodologies to next-generation technologies including AI, IoT, blockchain, and AR/VR, ensuring quality standards meet the ambitions of development teams.
