Standards
A controlled reference or acknowledged technical criterion.
See Also: IEC, IEEE, Mil, Interoperability Test, Compliance
-
Product
Humidity calibration with humidity calibrator
HUMOR 20
-
The role of humidity calibrations that are accurate, reproducible, and documentable is becoming more and more important. The humidity calibrator HUMOR 20 developed by E+E is the ideal reference instrument for these requirements and is traceable to international standards. The HUMOR 20 can be used in the humidity range of 10-95% RH both for monitoring cylindrical sensors and also for monitoring instruments with cubic dimensions.
-
Product
Test Set
TS® 30
-
Recognized as the industry standard for basic test sets, the TS30 Test Set provides superior quality at an affordable price. With its high impedance Monitor for DataSafe™ operation, technicians can clip onto a line in Monitor mode without disrupting existing traffic.
-
Product
VME Generic Carrier Card For PMC(PCIbus Mezzanine Card) Modules
AVC-2
-
VME64x (6U) generic carrier card for PMC (PCIbus mezzanine card) with 2 PMC slots. Modular solution combines any AIM PMC module for AFDX®/ARINC664P7, ARINC429, MIL-STD-1553 or any standard 3rd party PMC module.
-
Product
Mixed Signal Oscilloscope 100 MHz, 2 Analog Plus 16 Digital Channels
MSOX3012G
Oscilloscope
The MSOX3012G 100 MHz oscilloscope provides 2 analog plus 16 digital channels, 4 Mpts memory, 1,000,000 waveforms/sec update rate, zone touch trigger with an 8.5-in capacitive touch screen, and standard embedded software with waveform and measurement histograms.
-
Product
Alchitry Au+ FPGA Development Board (Xilinx Artix 7)
-
The Alchitry Au+ is the "gold" standard for FPGA development boards and it's possibly one of the strongest boards of its type on the market. The Au+ substitutes a more robust & scalable FPGA chip (Xilinx XC7A100T) that allows for more complex application circuits. The number of Configurable logic blocks (LABs/CLBs), Logic Elements, and total RAM bits are all nearly 3x that of the standard Au; see "Features" for more details.
-
Product
Downconverter
MADC-011021
-
Macom Technology Solutions Holdings Inc.
The MADC-011021 is a surface mount E-band receiver. The module operates from 71 - 86 GHz and is designed to be used in direct conversion or heterodyne applications. The RF input is a WR12 interface. The module provides 12 dB of conversion gain and a noise figure of 5 dB. The linear mixer topology allows for strong IIP3 performance (2 dBm) to be maintained up to the radio input levels recommended in the standards. The baseband is a quadrature balanced four line interface (I, I*, Q, Q*).
-
Product
Open Master/Slave Application Protoco
Modbus TCP
-
Modbus-TCP means that the Modbus protocol is used on top of Ethernet-TCP/IP. Modbus-TCP is an open Industrial Ethernet network which has been specified by the Modbus-IDA User Organization in co-operation with the Internet Engeneering Task Force (IETF) as an RFC Internet standard.
-
Product
2-Ch 500 MHz A/D with DDC & 2-Ch 800 MHz D/A with DUC, Virtex-7 FPGA - 3U VPX
Model 52751
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- Two 500 MHz 12-bit A/Ds- Two multiband DDCs (digital downconverters)- One DUC (digital upconverter)- Two 800 MHz 16-bit D/As- 4 GB of DDR3 SDRAM- Sample clock synchronization to external system reference- LVPECL clock/sync bus for multiboard synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x4- Optional user-configurable gigabit serial interface- Optional LVDS connections to the FPGA for custom I/O- Optional 400 MHz 14-bit A/Ds- 3U VPX form factor provides a compact, rugged platform- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Ring Wave Generator
SKS-1206IA/SKS-1206IB
-
Shanghai Sanki Electronic Industries Co., Ltd.
The ring wave generator is fully compliant with the new standards of IEC61000-4-12 and GB/T17626.12. The interface contains standard differences between IEC and Chinese national standards. Users can choose to enter the corresponding interface to perform different Test: Program -controlled high-voltage power supply and electronic switch have the characteristics of high precision, long life and good reproducibility.
-
Product
100BASE-T1 MEDIACONVERTER BCM
Art.-Nr.: TE-1000
-
The ideal physical layer conversion between Automotive Ethernet and your PC system. The 100BASE-T1 MediaConverter BCM establishes one direct point-to-point conversion between automotive ECU’s using 100BASE-T1 and any standard Fast Ethernet device with RJ-45 connector.
-
Product
EV& Charging Pile Test Set
DC Testing
-
With the development of Electric Vehicles in the world, more and more charging piles have been installed in different places. Due to the different understanding of the standards among EV manufacturers and charging piles suppliers, there may be hidden danger during the charging process.
-
Product
Acoustic Calibration Services - IEC
-
Acoustic Calibration Services - IECMake sure you measure correctly! We offer traceable acoustic calibration services according to international IEC and ANSI standards and ensure that your instrument accurately indicates the required measurement parameters. Calibrations are documented, traceable, and digitally signed in cooperation with an accredited calibration laboratory.
-
Product
Special / Customer Spec. Crates
6U VME NIX-I
-
The low-cost / industry standard VME/VME64 NIX-I series, provides basic, full size VME crates with low noise 6000 series based power supply technology and a removable fan tray.
-
Product
High Voltage Insulation Tester Module
DP-cPCI-5586
-
DP-cPCI-5586 is a High Voltage Insulation Tester Module. This module facilitates single-board voltage source/measurement features with high voltage output and a nanometer. Occupying a single slot in standard cPCI rack, this module can be used for multiple point cable harness test systems with limited rack space. Applications of this board include automatic test equipment, checkout systems, force voltage measure current, and insulation test.
-
Product
Field-installation Type MLSS Meter (Four-Wire Transmission)
HU-200SS
-
HU-200SS connects immersion type MLSS sensor (SS-90) and measures MLSS in activated sludge. A wide range (0-2000mg/L)of SS contents can be measured with excellent reproducibility using the near-infrared radiation transmission method. Any of the calibration curves of MLSS, Clay (inorganic mud) and Kaolin may be used as standard substances of SS. If "MLSS" is selected for an activated sludge treatment tank, "Clay" for the precipitation treatment of construction sludge, or "Kaolin" for white mud, a concentration can be obtained closer to an analyzed value.
-
Product
Combined Illumincance and Irradiance Probe
LP471P-A
-
Combined probe for measuring ILLUMINANCE (lux), with standard photopic response, and IRRADIANCE (μW/cm²) in the UVA spectral range (315…400 nm, with peak at 360 nm).
-
Product
DC High-Voltage Test Device
PGK 25
-
Cable testing with the BAUR PGK 25. Cables must be tested in compliance with the national and international standards. This applies before the commissioning of new cable networks. The portable BAUR PGK 25 cable test device is used for DC voltage testing in low- and medium-voltage cables. It is characterised by its low weight of only 16.5 kg, by the easy operation and solid construction for onsite use.* Compact device for DC voltage testing with negative polarity* Continuously adjustable output voltage* Perfect for mobile use
-
Product
Servicing and Testing of Search and Rescue Radar Transponder
SART
-
The Search and Rescue Radar Transponder as a part of GMDSS is a subject to annual test during radio survey. The annual testing of SART is recommended due to SOLAS regulation IV/15.8.The purpose of an annual testing is to determine that SART is operational as defined in appropriate performance standards for Survival Craft Radar Transponders for use in Search and Rescue Operations, IMO Resolution A.802 (19).Also Marine Orders require that a radar transponder must be inspected, tested and have its batteries replaced at intervals specified by its manufacturer.
-
Product
Rebound Hammer
SilverSchmidt - STL
-
Concrete test hammer SilverSchmidt Type ST L : *Standard impact energy (0.735 Nm) without PC communication*Use for concrete <10cm and fragile rocks*Measuring range: 10-100N/mm2
-
Product
SIGNAL & POWER ISOLATOR
EE301-ISOL
-
The EE301-ISOLATOR will completely isolate your electronic loads inputs & outputs signals plus ground returns from the main power input UUT (unit under test)... The module allows you to control the electronic load just as you would with any standard control signal. Input / Output & Power signals are fully isolated up to 350 VDC.
-
Product
Calibrators
-
Ensure the accuracy and reliability of your leak and flow testing instruments with our cutting-edge calibrator. Specifically designed for precision calibration, our product stands out in the market for its innovative technology and user-friendly features. Ideal for a wide range of industries, this calibrator is essential for maintaining the integrity of your leak and flow testing equipment. With its robust design and exceptional accuracy, our calibrator is a must-have for professionals seeking to uphold the highest standards in leak and flow measurement. Whether you’re in manufacturing, engineering, or quality control, our calibrator is the perfect tool to ensure your instruments are performing at their best. Discover the difference in precision and reliability with our top-tier calibrator for leak and flow testing instruments.
-
Product
Elongation Tester
SC-5
-
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.3-2008/IEC60851-3; Inspection standard: JB/T4279.3-2008Used to test elongation (ductility) of copper wires covered with φ0.100-3.0 mmenamel, silk or other insulation materials and other metal wires with tensile strength ≤2000N;Application of SCM control allows for fast operation and strong anti-interference capacity;Preset elongation of samples with two-digit toggle switch and, when the preset value is reached during test, motor and counter would automatically stop action and display results;The instrument is capable of measuring elongation while also the tensile force and holding the maximum tensile force value during stretching;Clamps are designed according to characteristics of various wires to prevent samples from breaking at clamp jaws, easy to load samples and, after samples are compressed, enamel can be automatically broken;While sample is broken, movable clamp would automatically stop moving, with error between displayed and actual elongation value less than 1%;
-
Product
Hardness-Rubber & Plastic (Dur
-
Durometers show the degree of hardness by value whether a non-rigid material like rubber is soft or hard (hardness gauge for rubber or plastic). Recently, JIS standard and ISO standard have been drastically revised and details of hardness tester of rubber and method of measuring hardness are changed.
-
Product
Oscilloscope - 1-6 GHz, 2 Analog Channels
DSOX6002A
Oscilloscope
1 GHz - 6 GHz2 analog channels Easily view and isolate signals on the 12.1-in capacitive multi-touch screen with Zone triggering and 450,000 wfms/s update rate Make more precise measurements with 115 Vrms noise floor at 1 mV/div (1 GHz)Get performance measurements anywhere with the portable 6-in deep size Quickly see analysis details with standard histogram and color grade View signal integrity with jitter and eye diagram analysis options
-
Product
MAX PH/ORP/ISE/Temp Logging Bench Meter
MW160
-
The Milwaukee MW160 4-in-1 MAX pH/OPR/ISE/Temp. Logging Bench Meter has won fans around the world with its reliable, fast, simple operation as well as a tough, sleek, lightweight design with a small lab space footprint. It is cccurate to ±0.01 pH with automatic or manual temperature compensation, and built in dedicated GLP key. In addition, up to 3-point automatic calibration and 7 selectable buffer standards makes the MW160 MAX ideal for use by brewers, wine makers, growers, labs, food processing, water treatment and many other applications with challenging pH measurement needs.
-
Product
Furnaces
-
These three zone resistance wire wound furnaces are of split construction to facilitate fast and easy loading of a pre-assembled specimen train. The case is constructed from stainless steel with aluminium and hardened insulation board end plates. The optional front cut-out allows the use of side-entry high-temperature extensometry. Adjustable stainless steel latches keep the furnace halves locked together during use, but are then easily opened once testing is complete. The furnace is available with optional heavy duty brackets or mountings, which attach to a wide range of testing systems. An extensive range of standard controllers is available to suit most test regimes. Custom variants can be specified should the standard range not include a suitable unit.
-
Product
Insulated Torque Wrenches
-
Intended for low and high voltage applications where torque is critical, Mountz insulated torque wrenches protect their operators in both low and high voltage situations. Essential for worker safety, insulated torque wrenches also improve work quality and productivity by preventing product damage due to arcing or shorting. Applications for linemen and electricians include a wide variety of live electrical situations, such as uninterrupted power supply repair. Mountz insulated torque wrenches meet IEC 6900 standards, keeping your workers safe.
-
Product
LXI/USB 18-Slot Modular Chassis
60-103D-001
Chassis
The 60-103D is an 18-slot LXI/USB Chassis fully compliant with the LXI Standard 1.4 and allows the large number of our 3U PXI modules to be installed and controlled through a standardized Ethernet interface or via a USB interface. Each module is supported as though it is an LXI compliant device, complete with a driverless soft front panel that provides control of the module functions.
-
Product
Flash In Disk-IDE
FID Series
-
Axiomtek's FID (Flash in Disk-ATA) series is a high performance 2.5 flash disk and fully compatible with IDE standard which make it an ideal replacement for conventional IDE HDD without any driver or system modification. This 2.5 IDE flash disk is provided with huge capacities up to 256GB to meet diverse needs of data storage. With the features of high capacity storage, data integrity, anti-vibration and low power consumption, the FID series is surely a solid solution for expanding an industrial computers memory.
-
Product
TySOM Embedded Prototyping Boards
-
TySOM™ is a family of embedded system prototyping boards. Depending on the board, one of three FPGAs will be at its heart: a Xilinx Zynq® UltraScale+™, a Xilinx Xilinx Zynq-7000 or a Microchip PolarFire SoC. The boards are compatible, through industry standard interfaces (FMC or BPX), with Aldec’s wide range daughter cards, making Aldec’s TySOM embedded prototyping boards ideal for the rapid development of applications that include automotive (and ADAS, in particular), artificial intelligence (AI), machine learning (ML), embedded vision, embedded-HPC (including edge-processing), IoT, IIoT and industrial automation.
