RF Voltmeters
Measures RF voltages on tuned circuits.
-
Product
RF Diagnostic Chamber
DST200
-
The R&S®DST200 RF diagnostic chamber is the ideal environment for RF analysis during development. It supports a wide range of radiated test applications for wireless devices and fits on any R&D lab bench, where it can be used at all times during the product design and optimization phase. The R&S®DST200 effectively assists in achieving high first-time pass rates during final type approval, which saves time and money.
-
Product
SP3T RF Pin Diode Switches To 18 GHz
-
Pulsar Microwave manufactures 3-way absorptive and reflective switches for use in 50-ohm systems. These SP3T switches operate from 100 MHz to 18 GHz and handle 200 mW input power. VSWR performance is often 1.6:1 or better with 100 ns switching time. Minimum isolation of 60 dB is specified for most units. Absorptive and reflective switches require +5V and -5V power supply to function. Control logic is from 0 to +5 volts. All voltage and ground connections are made by feed thru and turret terminals, respectively.
-
Product
Quad RF Driver
-
The Quad RF Driver contains four independent RF channels, each with an RF synthesizer, variable attenuator, and 1W power amplifier. The RF signal can originate from either the internal synthesizer or an external source via SMA input. All channels have independent frequency, phase, and gain settings and can be operated in one of two modes. The “Wideband” mode operates from 35MHz to 2GHz with a 3.472KHz resolution; over this range the frequency roll-off is approximately 0.5dB/100MHz. “Int-N Phase Adjust” mode allows the user to set and maintain a fixed phase relationship between all four channels. This mode is designed to operate between 300 and 460MHz with a 2MHz resolution. Two additional inputs are provided for an external frequency reference and digital modulation.
-
Product
RF Solutions
-
ST offers wideband and multiband RF solutions for wireless communication infrastructure and RF equipment including GSM/3G/LTE base stations, microwave links, cable modems, satellite, broadcasting, instrumentation, security, defense and test equipment.
-
Product
PXI/PXIe RF Multiplexer, Single 16-Channel, 3GHz, 50Ω, MCX
42-875A-101
Multiplexer Module
The 40-875A-101 (PXI) and 42-875A-101 (PXIe) are single 50 Ohm 16-channel RF multiplexers in a single slot. They have been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost.
-
Product
RF Power Splitter, Combiner, Divider
PD2460
-
INSTOCK Wireless Components, Inc
Wideband Frequency (350 - 1000 MHz)Low Insertion Loss (0.5 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.15 : 1 avg)RoHS Compliant Splitter ConstructionTri Alloy SMA Female (Jack) Low PIM
-
Product
PXI/PXIe RF Multiplexer, Dual 4-Channel, 3GHz, 50Ω, MCX
40-872A-102
Multiplexer Module
The 40-872A-102 (PXI) and 42-872A-102 (PXIe) are 50 Ohm 4 to 1 PXI RF multiplexers with 2 banks in a single slot. They have low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss.
-
Product
RF / MW switch
-
The RF / MW switch includes a variety of RF and microwave switch modules - RF multiplexers, which are available for use in the 34980A multifunction switch / measurement unit, providing broadband switching from DC to 20GHz . Use these modules to route test signals between your device under test and a signal source, oscilloscope, spectrum analyzer, or other instrument. The switch / attenuator driver module also controls the external switches and attenuators of the 34980A.
-
Product
Custom Radio Frequency (RF) Receivers & Sources
-
FLO – Frequency Locked Oscillators, IFM – Instantaneous Frequency Measurement, DCU – Digital Control Units, ACU – Antenna Control Units, IDCU – Integrated DCUs, and Other Custom Products
-
Product
RF Spectrum Analyzers & Signal Analyzers
-
RF Spectrum Analyzers & Signal Analyzers by Tektronix
-
Product
RF Safety Monitoring
MVG EME Guard XS 6GHz
-
The EME Guard XS is an RF measuring device to alert workers near RF emitters for protection of climbers and other RF-exposed workers. It continuously scans for electromagnetic waves and, via its built-in alarm and visual system, alerts users whenever the acceptable pre-selected limits have been exceeded. This RF Safety PPE is extremely easy to use and supports a safer working environment in the areas of installation and maintenance.
-
Product
PXI/PXIe RF Multiplexer, Single 4-Channel, 3GHz, 50Ω, SMB
40-872A-001
Multiplexer Module
The 40-872A-001 (PXI) and 42-872A-001 (PXIe) are 50 Ohm 4 to 1 RF multiplexers with 1 bank in a single slot. They have low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss. The injection of noise and unwanted signals into the signal paths of the 40/42-872A has been minimized by careful attention to the mechanical and electrical design.
-
Product
RF Shielded Chamber
MIL-STD
-
A high performance RF-shielded chamber specifically designed for radiated emissions testing in accordance with MIL-STD-461E/F. This chamber can be used for conducted emissions, conducted immunity, radiated emissions, and radiated immunity testing.
-
Product
PCI 8x9 RF Coaxial Matrix Card 75Ω SMB
50-725A-751
Matrix Switch Module
The 50-725A is an 8x9 RF Matrix Module suitable for switching frequencies up to 500MHz. The 50-725A is available in either 50Ω or 75Ω versions with SMB coaxial connectors. It is intended for the easy construction of high performance bidirectional matrix switching systems.
-
Product
RF Hybrid Couplers
-
Pasternack RF hybrid coupler series is passive devices that couple part of the transmission power in a transmission line. Our RF hybrid coupler components provide the bandwidth, high directivity and high power that designers need for their most demanding applications. 90 degree hybrid couplers often use two transmission lines set close together so that energy passing through one is coupled to the other. Many Pasternack 90 degree hybrid coupler items are RoHS and REACH compliant. Our RF hybrid coupler series is available with SMA connectors and 3dB coupling values. Power ratings for the 90 degree hybrid coupler product line range from 20 Watts to 50 Watts. 90 degree hybrids have a frequency range that is from 1 GHz to 18 GHz. As with the other over 40,000 RF, microwave and millimeter wave components from Pasternack, this RF hybrid coupler series is in-stock. Not just in stock, but these RF couplers in a hybrid design will also ship the same day as they are purchased.
-
Product
PXI Dual RF Attenuator 63dB in 1 dB steps
41-180-022
Attenuator
The 41-180 Programmable Attenuator Module is available with either one or two independently programmable attenuators in a single width 3U PXI module.
-
-
Product
RF Signal Detector
H-055DRV / 01019
-
The RF Signal Detector / 2G Cellular Phone Detector / Wireless Camera Detector / Bug Detector applies with fuzzy scanning technology to detect peeping cameras, tapping, cellular phones and other radio frequency devices.
-
Product
SP2T RF Pin Diode Switches To 18 GHz
-
Pulsar Microwave's 2-way switches are available in absorptive and reflective designs from 20 MHz to 18 GHz. They are also referred to as single pole, double throw and abbreviated SPDT or SP2T. These switches have a typical VSWR performance of 1.6:1 or better and input power handling of 200 milliwatts maximum. Switching time is 100 nanoseconds, and isolation of 60 dB or greater for most models. Supply voltages are +5V and -5V, with TTL logic control voltage of 0 to 5 volts.Both absorptive and reflective SPDT switches are packaged into Pulsar Microwave's SW2 outline. Configuration is standard with SMA female connectors. Voltage is applied with wire wrap feed thru terminals. The housing serves as electrical ground, and two turret terminals are installed for wiring.
-
Product
RF Test
-
RF is short for radio frequency. RF is any frequency within the electromagnetic spectrum associated with radio wave propagation. When an RF current is supplied to an antenna, an electromagnetic field is created that then is able to propagate through space. Many wireless technologies are based on RF field propagation. These frequencies make up part of the electromagnetic radiation spectrum.
-
Product
RF Sources
-
Textron Systems’ commercial RF Sources (RFS 340, SSI) provide an unmatched combination of frequency coverage, power range, signal fidelity and switching speed in either a two-slot VXI, 1U LXI®, or VME Synthetic Stimulus Instruments (SSI) format.
-
Product
PXI 8x2 RF Matrix 1.5GHz 50 SMB
40-750-511
Matrix Switch Module
The 40-750-511 is an 8x2 RF Matrix Module suitable for switching frequencies up to 1000MHz. It has a 50Ω characteristic impedance with front panel mounted SMB coaxial connectors. The matrix intended for the easy construction of high performance bidirectional switching systems.
-
Product
16-Bit, 12 GSPS, RF DAC and Direct Digital Synthesizer
AD9164
-
The AD9164 is a high performance, 16-bit digital-to-analog converter (DAC) and direct digital synthesizer (DDS) that supports update rates to 6 GSPS. The DAC core is based on a quad-switch architecture coupled with a 2× interpolator filter that enables an effective DAC update rate of up to 12 GSPS in some modes. The high dynamic range and bandwidth makes these DACs ideally suited for the most demanding high speed radio frequency (RF) DAC applications. The DDS consists of a bank of 32, 32-bit numerically controlled oscillators (NCOs), each with its own phase accumulator. When combined with a 100 MHz serial peripheral interface (SPI) and fast hop modes, phase coherent fast frequency hopping (FFH) is enabled, with several modes to support multiple applications.
-
Product
RF Testing Platform for ATx05
AT118
Test Platform
The functional test of modern devices with wireless connectivity always requires RF isolated cameras, as the only way to have the parameters controlled and to guarantee operation under the specified conditions.
-
Product
MS-M 26-Pin RF Cable Assembly 0.5m
40-979-526-0.5m-FU
RF Cable Assembly
The MS-M RF 26-Pin cable assembly is constructed from RG178 Silver Plated Copper Clad Steel Wire with PVC insulation and an attenuation of 1.08dB/m at 400MHz. Screwlocks are provided to secure the MS-M connector to the associated product.
-
Product
50 Ohm SMA to SMA Cable Assembly
40-977-521-2m
RF Cable Assembly
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
Product
PXI/PXIe RF Switch, Triple SPDT, 3GHz, 75Ω, MCX
42-830A-103
Switch Module
The 40-830A-103 (PXI) and 42-830A-103 (PXIe) are 75Ω RF switches with 3 separate SPDT relays in a single slot. They have been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The switch banks have been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss.
-
-
Product
Analog RF Slot Downconverter: 2000-2400 MHz Input
Model 8111-005
-
The Bandit® Model 8111 provides a series of high-performance, stand-alone analog RF slot downconverter modules. Packaged in a small, shielded enclosure with connectors for easy integration into RF systems, the modules offer programmable gain, high dynamic range and a low noise figure.
-
Product
With CATV RF Input EDFA
HA4600/RF
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HA4600/RF series is the narrow-band multiplexing EDFA which suitable with CATV application. This EDFA build-in one unit 1550nm direct modulated CATV transmitter used in inter cutting local VAD service. Build-in WDM multiplexing TX optical signal and External input optical signal of the main road then enter EDFA amplification, to server the local users. In order to avoid TX output optical power and the external input optical power does not fit the main road interfere with each other, the output power of the TX through the build-in VOA, from front panel adjust and set. The whole unit is concision, install and debug convenient. Providing high-quality, low-cost solution for all-optical relay 1550nm optical CATV systems, second-grade service area or administration village inter cut local VAD service.
