RF Voltmeters
Measures RF voltages on tuned circuits.
-
Product
RF Amplifiers Bias Controllers
-
RF amplifier bias controllers generate a regulated drain voltage and actively adjusts the gate voltage of an external amplifier to achieve constant bias current. It can be used to bias any enhancement and depletion type amplifier operating in Class-A regime with drain voltages (VDRAIN) as specified. These devices achieve excellent bias stability over supply, temperature and process variations, and eliminates the required calibration procedures used to prevent RF performance degradation due to such variations.
-
Product
RF Safety Monitoring
FieldSENSE 60
-
The fieldSENSE 60 personal RF monitor has a proven track record of durability that works as hard as you do. fieldSENSE 60 is specifically designed with the RF climber in mind.
-
Product
6U VPX Direct RF Processing System
VP460
System
The VP460 is designed to enable customers to begin development of their next generation systems using revolutionary new processor technology. It is in alignment with the SOSA™ Technical Standard to provide the interoperability required by the US Air Force, Army and Navy.
-
Product
Microwave / RF Systnesizers
-
Kratos Microwave Electronics Division
Kratos General Microwave (KGM) has developed a broad line of General Purpose RF and Microwave Synthesizers to be used in various applications. KGM has developed a line of high performance, broadband Fast Indirect Synthesizers (FIS) to provide a cost-effective solution to the requirements of new systems. Its high speed (as fast as 1 sec) provides an economical alternative to direct synthesizers for many applications. Because of its low phase noise, it is an excellent alternate to the much slower and generally less reliable YIG-based rf synthesizer.
-
Product
RF Communication Module
RF-200
-
The RF Communication module allows remote operation of asingle sensor or a chain of sensors. The remote single sensoror chain is connected to an RF Communication module and to aBattery Module which powers them all.
-
Product
RF Safety Monitoring
MVG EME Guard XS 40GHz
-
EME Guard XS 40 GHz has been specifically designed to cover the new 5G millimeter wave bands. This RF safety tool is important for keeping those working close to RF emitters safer. It is easy to use, continuously scanning electromagnetic waves, and alerts the user when acceptable pre-selected limits have been exceeded.
-
Product
Peak/Average Reading Broadband, Multirange Directional RF Wattmeter
83060
-
Similar in appearance and operation to our standard Model 81060 Wattmeter, the Model 83060 converts from Average Reading to Peak Reading, with the flip of a switch, by inserting a peak reading amplifier between the element and the meter
-
Product
LXI 50 RF Matrix - 2.4GHz
-
Pickering's LXI 50 RF Matrix - 2.4GHz design permits any single Y input to be connected to any single X input, permitting the concurrent connection of 16 RF paths. All signal paths are bi-directional permitting any connection to be used as an input or an output. These matrices can be supplied in a variety of configurations based on Y axis sizes of 4, 8 and 16 and X axis sizes up to 32. The smaller matrix sizes in the range are factory reconfigurable up to the maximum size.
-
Product
RF Bidirectional Amplifiers
-
Miniature, high-efficiency and linear bidirectional amplifier modules (transmit and receive). 1.0 to 2.5 GHz, automatic or manual T/R switching, high-efficiency or high-linearity models. Custom designs available through RF PA design services.
-
Product
Portable Monitoring Receiver and RF Recorder
IZT R3301
-
The IZT R3301 is a portable receiver with an integrated server for data recording. The receiver is optimized for recoding of RF signals in frequently changing environments. The RF characteristics of the IZT R3301 are identical to the IZT R3000 series. # HF-VUHF-SHF receiver# frequency 9kHz...3GHz (3...12GHz option)# continuous spectrum recording of 24 MHz bandwidth, IQ recording with 20 MHz
-
Product
RF & Microwave Power Meters
-
Our RF & microwave power sensors ensure precise and reliable measurements. They provide the highest measurement accuracy and speed, simple operation, technological leadership in thermal, diode and OTA core measurement elements as well as traceability to national standards.
-
Product
Single 32 to 1, 50 600MHz PXI RF Multiplexer
40-766-001
Multiplexer Module
This 4 to 1 multiplexer is part of a range of RF multiplexers available in the following configurations: dual, quad and octal 4 to 1, single, dual and quad 8 to 1, single and dual 16 to 1 and single 32 to 1. All multiplexers have the option of automatic terminations which offer advantages at system level by reducing the presence of standing waves in the system which can cause degradation in isolation and crosstalk.
-
Product
6GHz RF Analog Signal Generator Module
LS6081D
Signal Generator
The LS6081D, 6GHz Single Channel RF Analog Signal Generator, offers industry leading performance, combined with a compact small footprint form factor. The LS6081D features exceptionally fast switching speed, superior signal integrity and purity and all the necessary modulated signals for analog communication systems. The LS6081D was designed to offer industry leading price to performance ratio, needed from the R&D benches to the production lines.
-
Product
PXI 8x4 RF Matrix 300MHz 50Ω Multiway Connector
40-729-002
Matrix Switch Module
40-727/728/729 are RF Matrix Modules suitable for switching frequencies to 300MHz (50Ω version). The modules are available in either 50Ω or 75Ω versions with a choice of coaxial connectors. The 40-727/728/729 are designed designed to provide a simple and scalable bidirectional matrix to RF frequencies. They are intended for the easy construction of high performance bidirectional matrix switching systems.
-
Product
PXI Expandable 16x16 RF Matrix 75Ohm Type 43
45-720A-711
Matrix Switch Module
The 45-720A module is a 6U 16x16 RF Matrix suitable for switching frequencies to beyond 250MHz. The 45- 720A module is available in 50 and 75 Ohm versions with a choice of coaxial connectors. It is intended for the easy construction of high performance bidirectional matrix switching systems. Automatic Isolation Switches are located on all coaxial connectors, these disconnect the matrix from the external test fixture. This maximises isolation and RF performance.
-
Product
RF Bridge, 50 Ohm, 300 kHz to 6 GHz
86205A
-
The Keysight 86205A high directivity 50 ohm RF bridge offers unparalleled performance in a variety of general-purpose applications. It is ideal for accurate reflection measurements and signal leveling applications.
-
Product
RF Matrix Switch for Wireless Technologies up to 4 GHz
NEXUS-4
-
Quintech Electronics and Communications Inc.
The NEXUS-4 is a bi-directional fully non-blocking 3232 RF matrix switching system that can route any input ports to any outputs in a 6 RU chassis. With the frequency range of 700 MHz to 4 GHz and the capability of expanding to 256256, it enables large scale wireless testing that involves many MIMO base stations and devices. The built-in programmable attenuators and efficient automation interface provide ease-of-use testing of signal fade and emulation of mobility scenarios. It can dramatically increase lab efficiency by eliminating manual patch panel and cabling as it can be remotely reconfigured for different test setups consistently in seconds.
-
Product
26-Pin MS-M RF Connector Housing, Female
40-969-526-F
-
These components allow users or their designated cable assembly suppliers to create their own cabling solutions for use with the Souriau MS-M RF connection solution.
-
Product
1 GHz RF Switch Module
1260-58
Switch Module
The Astronics 1260-58 is a high-density switch module with four 1x8 coaxial trees. The 1260-58 is intended for use with function/pulse generators, universal timer/counters, oscilloscopes, high-speed digital test units, and other instruments involving high-frequency or fast rise-times.
-
Product
PXI/PXIe RF Multiplexer, Quad 4-Channel, 3GHz, 75Ω, MCX
40-832A-104
Multiplexer Module
The 40-832A-104 (PXI) and 42-832A-104 (PXIe) are 75 Ohm 4 to 1 RF multiplexers with 4 banks in a single slot. They have been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss.
-
Product
RF Shielded Test Enclosure, Slim rack mountable
JRE 1724A
-
Designed for testing devices with a flat form factor that need plenty of I/O, the rack-mountable JRE1724A is ideal. Similar to our JRE1724, but not as high, you can place multiple devices within its large footprint. Dual I/O panels allow for a multitude of connectors and interfaces. The JRE1724A comes standard with dual honeycomb style vents - pictured is the enclosure with optional cooling fan and USB2.0 interface.
-
Product
RF Amplifiers up to 1000 MHz
-
Narrow and Broad band high power RF modules and rack mount amplifier systems using solid state devices including LDMOS and GaAs in Class A and Class A/B topologies for Pulse, AM, FM, continuous wave and digital modulation applications that include EW, Radar, Jamming, EMI and EMC radiated immunity, and wireless communications testing.
-
Product
PXI Single RF Attenuator, 2.3GHz
41-181-021
Attenuator
The 41-181 Programmable Attenuator Module is available with either one or two independently programmable attenuators in a single width 3U PXI module. Each attenuator uses high reliability mechanical switches to operate binary weight attenuator pads, providing attenuation values from 0 to 63dB in 1dB steps. Attenuator operating time is typically just 5ms, ensuring fast setting times.
-
Product
RF Terminators
-
Typically placed at the end of a transmission line and is designed to match the cable's AC impedance.
-
Product
RF Semi-Rigid Cable Assemblies
-
The Semi-Rigid cables are available with a copper or aluminum jacket and available with a selection of different platings and 4 different diameters (.047", .085", .141" & .250"). The Conformable®, or Hand-Formable (BJ - Braided Jacket), has a tin filled braid with a metal foil underlay and is also available in the same diameters as the Semi-Rigid type . The Flexible version, our Mini-Flex, has an FEP jacket, round braid and inner spiral shields and is available in 2 diameters, .105" &.165". All 3 types (Semi-Rigid, Conformable & Mini-Flex) are manufactured using the same type dielectric core and have virtually the same electrical performance. The decision of which cable to use should be primarily based upon your application.
-
Product
RF Generator
-
SIGLENT’S SSG3000X series of signal generators have a frequency range of 9 kHz to 2.1 GHz/3.2 GHz. They provide normal analog modulation such as AM, FM, and PM. They also provide pulse modulation and pulse train generator. In addition, when used with baseband generator such as SDG6000X, They can generate IQ modulated signals. With their high accuracy and pure outputs, the SSG3000X series is the right choice for R&D, education, and manufacturing.
-
Product
12GHz RF Analog Signal Generator Module
LS1291D
Signal Generator
The LS1291D, 12GHz Single Channel RF Analog Signal Generator, offers industry leading performance, combined with a compact small footprint form factor. The LS1291D features exceptionally fast switching speed, superior signal integrity and purity and all the necessary modulated signals for analog communication systems. The LS1291D is designed to meet today’s most demanding specifications, needed from the R&D benches to the production lines.
-
-
Product
PXI/PXIe RF Switch, Triple SPDT, 3GHz, 75Ω, SMB
42-830A-003
Switch Module
The 40-830A-003 (PXI) and 42-830A-003 (PXIe) are 75Ω RF switches with 3 separate SPDT relays in a single slot. They have been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The switch banks have been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss.
-
Product
RF Products
-
We also provide measurement jigs for tests and measurement, and custom-designed products responding to your specific measurement and testing needs.
