RF Chambers
isolate and supress RF waves.
See Also: Chambers, TEM Cells, Acoustic Chambers, Altitude Chambers, Anechoic Chambers, Climate Chambers, Dust Chambers, Environmental Chambers, ESS Chambers, Humidity Chambers, Refrigerated Chambers, Reverberation Chambers, Salt Spray Chambers, Sound Chambers, Temperature Chambers, Temperature Humidity Chambers, Thermal Shock Chambers, Vacuum Chambers, RF Enclosures
-
Product
16-Bit, 12 GSPS, RF DAC and Direct Digital Synthesizer
AD9164
-
The AD9164 is a high performance, 16-bit digital-to-analog converter (DAC) and direct digital synthesizer (DDS) that supports update rates to 6 GSPS. The DAC core is based on a quad-switch architecture coupled with a 2× interpolator filter that enables an effective DAC update rate of up to 12 GSPS in some modes. The high dynamic range and bandwidth makes these DACs ideally suited for the most demanding high speed radio frequency (RF) DAC applications. The DDS consists of a bank of 32, 32-bit numerically controlled oscillators (NCOs), each with its own phase accumulator. When combined with a 100 MHz serial peripheral interface (SPI) and fast hop modes, phase coherent fast frequency hopping (FFH) is enabled, with several modes to support multiple applications.
-
Product
Single 8 to 1 50 600MHz PXI RF Multiplexer
40-762-001
Multiplexer Module
This 4 to 1 multiplexer is part of a range of RF multiplexers available in the following configurations: dual, quad and octal 4 to 1, single, dual and quad 8 to 1, single and dual 16 to 1 and single 32 to 1. All multiplexers have the option of automatic terminations which offer advantages at system level by reducing the presence of standing waves in the system which can cause degradation in isolation and crosstalk.
-
Product
PXI/PXIe RF Multiplexer, Single 16-Channel, 3GHz, 50Ω, SMB
42-875A-001
Multiplexer Module
The 40-875A-001 (PXI) and 42-875A-001 (PXIe) are single 50 Ohm 16-channel RF multiplexers in a single slot. They have been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost.
-
Product
RF High Power Broadband Amplifiers
-
Chengdu KeyLink Microwave Technology Co., Ltd.
Broadband amplifiers of KeyLink have exceptional RF and Microwave performance. These RF broadband amplifiers(wideband amplifiers) are available in wide frequency bands from 1 MHz to 18 GHz. Power levels for octave and multi-octave designs range from 1 watts to over 1000 watts. Applications of these broadband RF amplifiers range from radar, jamming, communication to test and measurement.
-
Product
Walk-In Environmental Test Chambers
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBELL’s Walk-in Environmental Test Chambers are available in large capacity test requirement, especially the EV battery, storage system and solar panel. We are able to provide various walk-in chamber specifications and customized design chamber to meet various special specimen size and test requirement. As an environmental test chamber manufacturer, we also provide walk-in environmental chambers for sale, all the walk-in environmental chamber cost is at factory price.
-
-
Product
Temperature Humidity Chamber
-
Xi'an LIB Environmental Simulation Industry
Designed to simulate precise environmental conditions for testing materials, components, and products.
-
Product
CobaltFx 9 GHz 4' FET RF Cable Kit
-
This is a Set of 4 cables, standard length 4 ft, for one extender: ULC50SMSM.4 cable (4)
-
Product
Ozone Climatic Test Chamber
-
The Ozone Test Chamber provide an effective solution to the testing of products for resistance against ozone degradation in a controlled environment. These test chambers function as static tensile test chambers as well as Rubber Test Chamber and are often used for studying static tensile deformation of various manufactured goods in the presence of ozone. The equipment works by exposing the test samples to uniform concentrations of ozone at constant temperatures and relative humidity in a sealed air environment. Under these conditions, the products undergo the process of corrosion which can be observed in the form of surface cracks and changes in other properties.
-
Product
Enlarge Environmental Chamber
REXMED REC-480
-
MOD. REC-480, AC 230/380/415V, 1/3 phase, Environmental chamber, HS CODE: 841989, UNCCS CODE: 484384, UMDNS CODE: 16327, Main construction: SS304, Interior: SS304, Exterior: SS304 powder coated, Insulation: Rigid polyurethane foam and glass wool, Controller: Fix point PID controller, temperature ˚C/PV and ˚C/SV, humidity %/PV and %/SV display and setting, Temperature range: -40˚C~100˚C, Humidity range: 20%RH~98%RH, Constancy: ±0.3˚C ±2.5%RH, Uniformity: ±1˚C ±3%RH, Temperature and humidity sensor: PT 100Ω, Temperature and humidity audio and visual warning and OFFS correction setting, Temperature heater: 2.3KW X 2pcs, Humidity heater: 4.5KW X 1pc, Heat up transition time: -40˚C~100˚C within 45 min, Refrigeration system: Air cooled, single stage, Cooling compressor: Bristol hermetic compressor, Cooling capacity: 5,270 Watts, 18,000 BTU/hr, 4,545 Kcal/hr, Cool down transition time: 20˚C~-40˚C within 50 min, Safety devices: No fuse breaker, refrigerator over load relay, refrigeration high pressure switch, over temperature protector, protection relay, protection fuse, water level control and overheat protector, Chamber: L100 X W80 X H100cm, Capacity: 800L, chamber with key lock, with lamp (DC 12V 50W) X 1pcs and double glass viewing window, testing cable port with cover: Ø25mm, 4 castors, W/S: shelf X 2pcs, standard testing wet cloth X 5pcs, PCV water container X 1pc
-
Product
RF Data, manipulation software
EMiDat
-
EMiDat is a powerful Windows application allowing the manipulation of calibration data for the assessment of absorber lined screened rooms. Field uniformity can be established giving both graphical and tabular information
-
Product
Burn-in Room and Aging Test Chamber
-
Isolated type of burn-in room features: ●Separate the product and loading area, easy to control temperature and maintain. ●Temp. range: 40-70ºC±3/±5ºC, ●Temp. constancy: ±0.5ºC ●Uniformity: ±3ºC ●Test frame materials: painted stainless steel or a combination of forming aluminum ●Insulation: with PU foam ( doors with double glazing ) insulation, so that the internal temperature is not subject to external factors, to achieve power saving effect ●Product hierarchy placement, Selection of layer height in accordance with the requirements, convenient access ●Computer monitoring system is optional. ●Noise level:≤75dB Application Suitable for all kinds of electronic products, especially for products with heating characteristics Product and loading area should be separated Large-scale production
-
Product
RF Shield Box
CMW-Z10
-
The R&S®CMW-Z10 has excellent shielding effectiveness and superior coupling characteristics.The shield box can be used for frequencies up to 6 GHz.The antenna structure is optimized to enable excellent radio connections between the DUT and tester.The highly broadband spiral antenna allows a wide variety of applications.These outstanding features combined with modular options make the RF shield box indispensable for any radiocommunications tester.
-
Product
PXI-5651, 3.3 GHz RF Signal Generator
779670-01
Signal Generator
3.3 GHz PXI RF Analog Signal Generator—The PXI‑5651 features continuous-wave generation capabilities with FM, 2‑FSK, or OOK modulation. It uses direct digital synthesis (DDS) for high-resolution frequency hopping or phase-continuous sweeping for fixture and device characterization applications. The PXI‑5651 is ideal for clocking nonstandard sample rates, such as WCDMA signals at baseband or intermediate frequency (IF). With these versatile signal generators, you can perform analog and digital modulation through the onboard DDS circuit, which gives you frequency modulation and frequency-shift keying for applications such as bit error rate test, antenna testing, or even keyless entry. You can also perform amplitude modulation using on-off keying.
-
Product
SP5T RF Pin Diode Switches To 12 GHz
-
Pulsar Microwave's 5-way RF switches cover bands from 300 MHz to 12 GHz in both absorptive and reflective configuration. These SP5T switches have a rating of 200 mW maximum input power and a switching time of 100 ns. They are specified with a minimum isolation of 60 dB and most models maintain a VSWR of 1.6:1 or better on all ports. The SP5T switches are driven by TTL logic control circuitry and require both positive and negative 5-volt supplies for operation. A 9-pin D-SUB connector provides the interface for the power and logic voltages.
-
Product
RF Mixers & Frequency Converters Overview
-
Up and down conversion is often used because waveform generation in a transmitter is less expensive at lower frequencies and the dynamic range of analogue-to-digital converters in the receiver is higher at lower frequency.
-
Product
Salt Spray Test Chamber
-
Dongguan Kejian Instrument Co., Ltd.
Corrosion resistance salt spray testing machine can be used to determine the corrosion resistance of inorganic or organic coatings of ferrous or non-ferrous metals, such as electroplating, anodizing, chemical processing, painting and other surface treatments.
-
Product
RF Matrix Switch for Wireless Technologies up to 4 GHz
NEXUS-4
-
Quintech Electronics and Communications Inc.
The NEXUS-4 is a bi-directional fully non-blocking 3232 RF matrix switching system that can route any input ports to any outputs in a 6 RU chassis. With the frequency range of 700 MHz to 4 GHz and the capability of expanding to 256256, it enables large scale wireless testing that involves many MIMO base stations and devices. The built-in programmable attenuators and efficient automation interface provide ease-of-use testing of signal fade and emulation of mobility scenarios. It can dramatically increase lab efficiency by eliminating manual patch panel and cabling as it can be remotely reconfigured for different test setups consistently in seconds.
-
Product
True RMS RF Millivoltmeter
3440A
-
The 3440A measures the true rms of low level RF and microwave signals to over 1GHz. High rms accuracy, traceable to NIST, is assured regardless of waveshape. Common calibration errors are eliminated through temperature compensation of the probe detector diodes; double shielding protects the interchangeable probes from rough handling and pickup. Relative gain or loss measurements are simplified by a 0 dB reference adjustment. DC output proportional to the ac input is provided for analog recorders and to allow operation as an ac-dc converter.
-
Product
Envinronmental Chambers
-
MRC environmental test chambers with temperature and humidity control. Chamber Test Humidity and Temperature Programmable humidity and temperature of range full a simulates freezing, climatic, durability, reliability test to conditions .etc endurance thermal, assurance quality.
-
Product
802.11a,b,g RF Shielded Test Enclosure
JRE 0814-A
-
Testing tall devices? The 0814-A stands up to any test up to 18 GHz! Featuring a wide swing open door with durable latch handle, this enclosure is ideal for testing IEEE 802.11 a,b,g devices such as; WLAN, VoIP, access points and other RF devices.
-
Product
DC Blocking RF Splitter Combiner
PD5180
-
INSTOCK Wireless Components, Inc
Wideband Frequency (698 - 2700 MHz)Low Insertion Loss (0.6 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.15 : 1 avg)50 VDC maximum on DC block portTri Alloy SMA Female (Jack) 50 Ohm
-
Product
Rotary Thermal Shock Chambers
TS Series
-
A Bemco exclusive product, the TS Series of Turboshock Rotary Thermal Shock Chambers feature an electrically driven, 180 degree reversing, rotating wall located between two chambers, one hot and one cold. Two loads can be handled simultaneously. Front loading and rear access doors allow full entry to each zone.
-
Product
Archival Storage Chambers
AR Series
-
The Darwin Chambers AR series is designed specifically for the needs of archival preservation. This series is capable of providing long-term controlled storage of photographs, film, rare books, papers, and paintings. Utilizing a simple. precisely controlled refrigeration system and advanced desiccant-based dehumidification, temperatures are maintained to within ±0.2ºC (at the sensor) and relative humidity to within ±1% (at the sensor).
-
Product
PXI/PXIe RF Multiplexer, Single 4-Channel, 3GHz, 50Ω, MCX
40-872A-101
Multiplexer Module
The 40-872A-101 (PXI) and 42-872A-101 (PXIe) are 50 Ohm 4 to 1 RF multiplexers with 1 bank in a single slot. They have low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss. The injection of noise and unwanted signals into the signal paths of the 40/42-872A has been minimized by careful attention to the mechanical and electrical design.
-
Product
VHF Band 1.0 Watt Amplifier With RF Bypass
-
Teledyne RF & Microwave has developed a 35 to 350 MHz custom amplifier with 1 watt output power. The amplifier has 29 dB gain with 3 dB noise figure. The amplifier assembly has a RF switch so that the RF input can be connected directly to the output bypassing the amplifier. The amplifier goes into the "bypass" state when the DC bias is removed from the switch. This unit is one of a series of amplifiers that covers the 1 MHz to 2100 MHz with similar operation.
-
Product
Cyclic Corrosion Testing Chambers
-
Weice Testing Instrument Co.,Ltd.
Any combination of different environments may be programmed to occur sequentially in any order, to form a corrosion cycle which will then be performed automatically or repeated a pre-set number of times. Each environment can also be selected individually.
-
Product
Temperature Test Chamber
-
Temperature Test Chamber is designed for testing the capability of heat-endurance, cold-endurance, dryness-endurance, and humidity-endurance, suitable for quality control of the industries of electron, electrical equipment, vehicle, metal, foodstuffs, chemistry, building materials, luggage, adhesion tape, printing, packaging, etc.
-
Product
RF Prototyping Kit
VXI-5501
-
* VXI-5501 has a Bare Copper-clad Prototyping Board for RF and microwave modules.* Includes a VXI-5524 Register Based Interface Board with 48 digital IO lines and a 16-bit VXI data bus.* User configurable model number, manufacturer ID, version and serial numbers identifies the module as from your company.* Includes a blank front panel, side shields, manual, layout aids and VXI-Kit hardware for a single slot wide C-size module.
-
Product
RF Generators
-
Produce radio frequency (RF) signal for device evaluation and fault detection.
