Showing results: 3406 - 3420 of 4155 items found.
-
SG3005 -
Shanghai Jiuzhi Electric Co., Ltd.
The instrument can measure DC positive and negative value of DC voltage, ripple voltage, ripple factor. It can measure AC sine wave (power frequency) and the AC of non-sinusoidal wave voltage peak (positive peak value, negative peak value, peak-peak value), peak value/ √ 2 (true RMS), RMS value of waveform deviation factor and higher harmonics. And can display and save the voltage waveform, pressure raising curve.
-
Kvtester Electronics Technology Co.,Ltd
High precision instrument for measuring characteristic parameters of transformer capacity, no-load and load. The instrument is a multi-function measuring instrument, which is equivalent to the usual two kinds of test instruments: the transformer capacity tester + transformer characteristic parameter tester. The utility model can precisely measure a series of power frequency parameters of a plurality of transformers, such as the capacity, the type, the no-load current, the no-load loss, the short circuit (load) loss and the impedance voltage.
-
YAV90084A -
6TL Engineering
4x 8-Bit 1KOhm reostat 4x 8-Bit 40 Ohm reostat 2x 8-Bit 5 MOhm reostat 10x Electronic Potentiometer 8-bit resolution -256 steps- with build-in selft test. 10x Voltage to current source 0(4)..20mA 10x Analog Outputs (Buffer for voltage or frequency) 36-Ch Test Point voltage divider 2xCAN Bus Channels Terminators tester Expandable with NI PXI-6723 and PXI-6345.
-
MKQA-610 -
Guilin Mingke
QAM modulator with DVB-C standard television signals by MPEG-II coding and other data stream rehabilitation to deal with, and then into the QAM modulator, QAM coding is based on the DVB technical specifications, such as cutting, RS FEC Coding, and so on. The IF frequency to deal with later on TV channels, in order to HFC, MMDS microwave transmission network, can be used for digital TV, data broadcasting, video-on-demand, Internet, video conference and other digital broadband applications
-
Guangzhou Jumho Electric Co., Ltd.
Cell phones and other wireless devices radiate powerful electromagnetic fields that can cause interference and noise in microphone signals. The interference and noise is called RF interference, which is an unwanted “signal” that occurs at the same time and frequency as a data signal. The RF interference disrupts the flow of data and degrades quality-of-service. Jumho Electric provides a cost-effective RF interference test system for GSM interference level measurement of wireless microphone.
-
Teledyne Defense Electronics
Teledyne RF & Microwave offers a capable range of high performance IQ Modulators and Image Reject Mixers as well as IQ (Quadraphase) Modulators which can be used on applications from commercial test equipment to space qualified projects. IQM products can be used either as an IQ modulator or IQ demodulator and cover several frequency bands from 1.4 GHz to 18 GHz. Click on the model number to view the available datasheets.
-
M9381A -
Keysight Technologies
Choose your RF modulation bandwidth, 40, 100, or 160 MHz, and easily upgrade as test needs change Increase throughput with fastest RF frequency tuning and amplitude switching for high-speed automated test Save space with a compact solution for up to 8x8 MIMO with phase coherence Get up and running quickly with validated application-specific reference solutions Simplify signal creation with Keysight's Signal Studio and Waveform Creator
-
11667A -
Keysight Technologies
The Keysight 11667A power splitter is recommended when making wideband ratio measurements using a Keysight 8757 scalar network analyzer. This two-resistor type power splitter provides excellent output SWR at the auxilliary arm when used for source leveling or ratio measurement applications. The tracking between output arms over a frequency range from dc to 18 GHz allows wideband measurements to be made with a minimum of uncertainty.
-
ST-2000 Cos∮ -
Standard Electric Works Co., Ltd
● Principle : Phase angle sensing transducer● Rated Accuracy : ±3% phase angle● Scale : Power Factor：Lead 0 – 0.3 – 1.0 – 0.3 – 0 Lag Power Angle： Lead 90° – 0° – 90° Lag● Effective Power Factor Measuring Range : Lead 0.5 – 1.0 – 0.5 Lag● Scale Length : Approx. 135mm(5-3/8”)● Frequency Influence : Within ±1.5° phase angle at 45 to 65Hz
-
289 SVD -
Standard Electric Works Co., Ltd
● Bright LED visual indication● Audible indication● Mute function● AC voltage detection: 100Vac ~ 69kVac● Frequency range: 50/60Hz● Easy-to-prove method● Self-test function● Power source: 1.5V(AA) alkaline battery × 3● Non-contact detection by proximity● Personal sensor, easy to wear and convenient to use● Can be attached with hot sticks by optional accessory● Lightweight, robust and compact● Easy access to batteries Comply with EN 61326-1
-
1612 EL -
Standard Electric Works Co., Ltd
●Microprocessor-controlled●Extra large LCD (78 × 67mm)●Very low power consumption●50Hz and 60Hz operation●Accurate digital readout of disconnection time●Over temperature protection●Over voltage protection●Fuse protection●Zero crossing circuitry permits testing at 0° or 180°●Auto power off●Backlight function●Wiring polarity indicator●Measures voltage between Line and Earth before testing●Frequency measurement indication
-
LS-96 SYNC -
Standard Electric Works Co., Ltd
● Input Voltage : 110V AC, 120V AC, 220V AC, 230V AC or 240V AC.● Square shape panel 96 x 96mm● 3 bi-colored LED indicators for "SYNC", "GEN" and "BUS"● 24 LEDs in a circle display the phase angle and the frequency differences between 2 networks● 360° indication● 12 o'clock position LED is bi-colored● PC window, ABS resin frame, PC case
-
1812 EL -
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● 2Lines × 16 Characters LCD.● Very low consumption.● Menu-driven.● Accurate digital readout of disconnection time.● Automatic data hold function.● Zero Crossing Circuitry permit testing at 0° or 180°.● Disconnection Phase Polarity shown on LCD display.● Auto-off and off override.● Polarity Trip indicator (Positive of Negative Phase).● Wiring polarity indicator.● Measure voltage and frequency between Line and Earth before testing.
-
Micropross MP500 PT1-NFC -
NI
Support for ISO 14443 A/B, ISO 15693, MIFARE™, FeliCa™. Measurement correlation with NFC Forum and EMVCo certification test bench. Automated test executive with ready-to-run test sequences. Reader/Writer and Card Emulation modes, resonance frequency measurements supported on same antenna. Embedded analog measurements - LMA, field strength, S11, Q factor, waveform characteristics. Physical parameter/waveshape characteristic definition
-
PQM-703 -
Sonel S.A.
Power quality analyzer PQM- 703 is a technically advanced product that allows for comprehensive measurements of the quality of electricity , analysis and recording of power network parameters, for frequencies 50/60 Hz in accordance with European standard EN 50160. PQM -703 is another representative of a well, known family of analyzers line PQM- 70x . In relation to the PQM -702 has new functions like recording of transients with max. sampling frequency 10 MHz (rapid changes in voltage) and control signals. Minimal transient capturing time is 650 ns. It is intended for a very wide range of users who need to control the quality of power with a mobile device , which fulfills the requirements of a multi-sheet standard IEC 61000 for class A analyzers. This applies to measurement accuracy, measurement methods, and synchronization of time with a standard signal. The last condition is met with a built-in GPS module with an internal antenna. If the analyzer is installed inside, it is possible to use an additional antenna with a 10m-long wire. If the antenna is situated outside, GPS signal will be attainable without any problems and used for the synchronization of an internal clock.
