Torque
turning force.
See Also: Torque Sensors, Torque Testers, Torque Transducers, Torque Meters, Dynamometers
-
Product
19mm N-Type Torque Wrench
CMT TW-N
-
The TW-N is a N-Type, proof coupling torque wrench used to properly install or disassemble a wide range of coaxial connectors.
-
Product
Load Cell Transmitter
MODEL SST-HV
-
The SST-HV is a Plug & Play Smart TEDS IEEE 1451.4 compliant Transmitter. Just plug in a TEDS compatible Load Cell or Torque Sensor and the SST-HV will automatically self-calibrate. When used with a non-TEDS Load Cell or Torque Sensor, the SST-LV Transmitter is easily programmed using a PC with an RS232 port and Instrument Setup (IS) software, which provides a graphical user interface. The SST-HV may be powered from 95-240 Vac ±10%. The SST-HV has an Isolated transducer excitation output that is selectable between 5Vdc or 10Vdc. There are Dual solid state relays and an Isolated 4-20 mA, 0-20 mA or 0-10V analog output. There are three Isolated serial data transmitter output ( RS232 , Half-duplex RS485, full-duplex RS485 ) and three serial protocols that are software selectable (Modbus RTU, Modbus ASCII and Custom ASCII). Isolation to 250V rms is provided for power, signal input, analog output, relay outputs, and communications. Isolation adds safety and avoids possible ground loops. The transducer excitation output is isolated to 50V from signal ground.
-
Product
Instrument Grade Data Sensor
WISER 8000
-
TECAT Performance Systems, LLC
The TECAT WISER Model 8000 dual strain measurement and monitoring system is a wireless data acquisition system for measuring two external strain channels at high data rates up to 8kHz. The small, light, power-efficient, and non-invasive design enables strain measurements in a wide range of applications. With dual external sensor inputs two Micro-Measurements strain gauge bridges can be measured by a single system, for example to measure both thrust and torque loads simultaneously.The Model 8000 has a long range data transmission of >1,000 meters with up to +/- 0.025% FSR sensitivity for remote measurements. After initial setup using the WISER software interface, the system can be wired directly to your DAQ system, for seamless data collection.
-
Product
E-DRIV® Electric Screwdrivers
K-Series
-
The K-Series are low voltage DC electric screwdrivers. These rugged assembly tools increase productivity and enhance product quality through precision torque control and user comfort. The electric screwdrivers automatically stop when the preset torque has been reached. The K-Series electric screwdrivers are NRTL certified from TUV America, Inc. The certification ensures manufacturing companies that they are purchasing and operating a quality and safe tool for its operators.
-
Product
Multi-Axis Sensors
-
Interface multi-axis sensors are designed to measure multiple forces and moments simultaneously with a single load cell sensor. These sensors provide multiple bridges that precisely measure the applied force from one direction with little or no cross-talk from the force or moment. Our 2-axis, 3-axis, 6-axis, and axial torsion load cells provide the ultimate in force and torque measurement. We can measure forces simultaneously in three mutually perpendicular axes, with the 6-axis load cells also measuring torque around those axes.
-
Product
Magnetic Level Gauge Switches
-
ABB's magnetic level gauge switches for point level alarm and/or control can mount to a KM26 magnetic level gauge or an LS Series cage level switch.These switches are completely isolated from the process fluid as they are magnetically activated by a magnet equipped float (KM26) or attraction sleeve (LS Series). The unique magnetic coupling action eliminates seals, diaphragms, springs, and torque tubes common to other level switching alternatives since there is no physical contact with the process fluid. The magnetic coupling also eliminates process connections to the switch; therefore, no isolation valves are required to block off the switch for maintenance. The switch "set point" is easily adjustable without changing any process piping and the result is a more reliable and easier way to maintain level system.
-
Product
E-DRIV® Brushless Electric Screwdrivers
HF-Series
-
The brushless electric torque screwdriver is built for precision torque control. The electric screwdriver ensures quality and reduces overall assembly failures. These durable power tools feature a Swiss Maxon brushless motor design, which reduces the common maintenance costs associated brush type electric screwdrivers. With almost no expendable parts and simple design, the brushless screwdriver life cycle is extended and maintains a clean working environment. The screwdriver requires less maintenance and part replacement and provides consistently reliable performance. Using a quality brushless electric screwdriver makes a safer world through accuracy and precision.
-
Product
Encoders & Potentiometers
-
Panasonic Industrial Devices Sales Company of America
Encoders convert the manual rotary operation of an actuator or knob into coded signal outputs and offer options such as various detents, high torque, push-on switch, long life, water proof and center space.
-
Product
Sensors
-
Com-Ten offers a wide range of sensors to suit your different applications. Force and torque sensors of various capacities and sizes, combined to wired and wireless measurement displays, we can offer you a solution for your testing needs.
-
Product
Digital Force Gauges
-
Digital force gauges are powerful yet user-friendly gauges, designed for either handheld use or test stand mounting. These digital force gauges and torque gauges offer the best price performance value of any digital force gauge available, along with a high precision and an easy to use force measurement solution.
-
Product
Torsion Testers
-
For maximum torsion testing versatility and capability, Tinius Olsen offers a full range of torsion testing machines in capacities from 1,000 to 30,000 Nm. These uniquely superior torsion testers provide loading and weighing capabilities in both directions of rotation. This feature makes it possible to conveniently determine not only the ultimate torque load of a specimen, but how that specimen behaves under conditions of continuous or intermittent torque loading in both directions.
-
Product
Oscillating Disc Rheometer
EKT-100H
-
Designed and manufactured in accordance with ASTM D2048& ISO 6502 standards. Output, displayed and memorized graphics including Elastic torque, Cure rate, and Upper/Lower dies temperatures. More than 30 items of data, such as ML, MH, TS, TC, CRI etc., couble be taken from each test. Cure curve provides the processing, vulcanizing, and vulcanized physical properties of rubber cross-linking reaction.
-
Product
Engine Dynamometer
DH21
-
Power: 270 hp (205 kW)Torque: 425 lb-ft (576 Nm)Speed: 5,500 rpmWater Use*: 20 gpm (75.7 lpm)Inertia Value: 3.4 lb·ft2 (0.143 kg·m2)Shipping Weight: 325 lb (147 kg)*No Cooling System
-
Product
Steering Effort Sensor
CLSx
-
With the innovative CLSx steering effort sensor, the original steering wheel of your vehicle becomes a high-precision instrument that measures steering torque, angle, steering velocity and acceleration in x, y and z directions. Whether passenger car, truck or construction machinery, the ultra-slim sensor can be placed between the steering column and steering wheel in just a few simple steps. The functionality of the original steering wheel including airbag is completely preserved.
-
Product
Dial Weight Dynamometers
-
The most important characteristic of any measurement instrument is repeatability and accuracy. The Magtrol Dial Weight Dynamometer uses the combination of a Hysteresis Brake and gravity to insure constant, reliable results. The brake torque rise is directly proportional to applied current
-
Product
AC Engine Dynamometer
DA900
-
Power: 1000 hp (746 kW)Torque: 3,501 lb-ft (4,747 Nm)Maximum Speed: 3,000 rpmConstant Torque Range: 0 - 1,600 rpmConstant Power Range: 1,600 - 2,400 rpmDecreasing Power Range: 2,400 - 3,000 rpmRotation: bi-directional
-
Product
Hot Torsion Mobile Conversion Unit
-
Capable of applying torque up to 100 Nm (50 Nm standard configuration), Hot Torsion Systems from Dynamic Systems are the first commercially available torsion systems to incorporate direct resistance heating.
-
Product
Swivel Joints
-
The Swivel Joint is a special type of RF waveguide joint. It is a joint that is limited in rotation angle, compact in size, with low mechanical torque and high peak power capacity.
-
Product
Programmable Selsyn Indicators
PSI
-
Computer Conversions Corporation
Computer Conversions Solid State Selsyn/Resolver Indicator digitizes the outputs of Selsyns, Synchros and Resolvers for position indication and control applications. The Selsyn Indicator is designed to replace failure prone mechanical selsyn torque receivers, counters, etc. The tracking converters high noise immunity and high speed tracking characteristics make it ideal for use in industrial envrionments.
-
Product
Robotic Electric Screwdrivers
CLF-Series
-
The HIOS CLF-Series is designed for robotic and automated fastening applications. The durable robotic screwdrivers deliver reliability and precision torque control. Ensures accuracy in fastening with precision automatic shut-off clutch once preset torque is achieved.
-
Product
Pneumatic Multipliers
CLS
-
The CLS pneumatic torque multiplier provides precision tightening and loosening of all heavy duty fastening connections. The torque multiplier shuts-off when pre-set torque is achieved. It's a non-impacting and operates at a smooth, continuous rotation, the torque multiplier increases speed and productivity, as it is faster than a hydraulic wrench and is less expensive.
-
Product
DC Control Tools
-
Assembly designs are getting more and more complex while production speeds continue to increase. To compete, lean manufacturers strive to complete more work with fewer tools. A single Mountz DC control tool can do the work of 2-15 regular tools, saving space and increasing production. Mountz DC control tools are easy to program and can remember up to 30 process sequences with 20 program steps. This gives you the flexibility you need to carry out varied and complicated manufacturing plans. A Swiss DC servo motor controls torque delivery with clockwork repeatability. Combined with built-in screw counters and error-proofing software, Mountz DC control tools offer supreme production results and product oversight. And by providing documented fastening results, Mountz DC control tools also make regulatory compliance easy.
-
Product
Torque Sensors/Transducers
TorqSense
-
We offer a range of rotary torque sensors and torque transducers to suit a variety of industrial applications, our standard range of sensors can measure torque ranges from 10mNm up to 13000Nm. Please browse our product range below or use the torque selector to assist in finding a torque sensor to meet your specific requirements.
-
Product
Digital Lamp Cap Torque Meter
CX-L338
-
Shenzhen Chuangxin Instruments Co., Ltd.
Lamp Cap Torsion Meter is a newly developed intelligent product with microprocessor built-in.
-
Product
Linear Amplifiers
LA Series
-
Motion Control Systems'' linear amplifiers are high performance servo controllers that produce very smooth sinusoidal motor currents using a linear amplifier output stage. In combination with a sinusoidally wound MCS brushless motor, the linear amplifier can achieve extremely precise rotational control with less than 1% torque ripple, no acoustic noise and almost undetectable levels of electromagnetic interference. Standard programmable features allow greater design flexibility, easy installation and start-up.
-
Product
Impact Tools
D914™ Series
-
The D914™ Series impact tools provide quality terminations on the first punch, helping to achieve the highest quality possible on network installations. They are the only impact tools that combine torque and impact in one tool. They also include a built-in hook and spudger into the handle. Use the hook to remove wires from any style block or to help trace wires. Use the spudger to remove the cross-connect module from the mounting bracket. Quick and easy blade replacement, and extra blade storage available in the handle.
-
Product
Wheel Torque Transducer
WTT-Dx
-
In automotive development, it is important to know the exact torques acting on the vehicle – especially under acceleration and braking maneuvers. With the WTT-Dx wheel torque transducer, a high-precision tool is available for making such measurements. The WTT detects the mechanical load directly where it is produced: the wheels that form the interface between the vehicle and the road.
-
Product
Click Wrenches
-
For good torque control at a great price, equip your shop with Mountz click wrenches. Strong, durable, and reliable, our click wrenches deliver the power you need to tighten any bolt. Your user will know when they've reached the sweet spot when they hear the audible click. This enhances process control and product quality by helping to prevent over- or under-torqued bolts.
-
Product
XP-Series In-Line Air Screwdrivers
-
Crafted for high production environments, the Flex Power In-Line air screwdriver provides durability, power and speed for assembly and manufacturing applications at an affordable price. Designed for safe operation and increase comfort for operators, the Flex Power tools provide lower noise decibels than comparative air tools as well as minimal vibration and low torque reaction on the operator. Featuring a patented clutch design the Flex Power tools delivers reliable accuracy with repeatable torque control. The clutch mechanism shuts off the air supply when the preset torque setting is achieved, preventing over-torque conditions from occurring.
-
Product
BF-Series Mini Screwdriver Models
-
The E-DRIV® BF-Series miniature soft stop models is designed with an unique "soft-stop" shock absorbing clutch that is ideal for fastening shock delicate components such as disk drives, plastics, and electronics. The ergonomically designed soft stop clutch reduces impact and vibration transmitted in the screw fastening process, which delivers less torque reaction to operator. The electric screwdriver offers an adjustable speed setting. Designed for precision torque control the brushless motor design ensures durability and reduces the standard maintenance costs associated with brush type electric screwdrivers. The mini BF power tool is ESD certified, ensuring less than 1 Ohm at the bit tip. ESD management assures product quality, cost savings and a reduction in overall ESD failures.
