PXI Carriers
-
Product
PXI 10A Power Multiplexer, 4-Bank, 8-Channel
40-661A-002
Multiplexer Module
The 40-661A-002 is a single pole, 4-bank, 8-channel PXI power multiplexer module, suitable for switching inductive/capacitive loads up to 10A with 125VDC/250VAC hot switching and 400VDC/250VAC cold switching. The multiplexer is available in 8-bank 4-channel, 5-bank 6-channel, 4-bank 8-channel, 2-bank 16-channel and 1-bank 32-channel formats.
-
Product
PXI Data Communications Multiplexer
40-736-001
Multiplexer Module
This Data Communications Multiplexer is designed specifically for multiplexing or de-multiplexing up to 32 differential signal pairs having controlled 100 differential impedance. The multiplexer can be configured under software control to provide switching for 32 differential pairs, 16 dual differential pairs and 8 quad differential pairs. The dual and quad versions are particular well suited for providing switching of AFDX, BroadR-Reach and Ethernet signals. To support Ethernet applications, the design includes a switching network that simplifies the swapping of Tx and Rx pairs to simulate the effect of Ethernet crossover cables.
-
Product
PXI Low Thermal Multiplexer, 23-Channel
40-620A-022
Multiplexer Module
The 40-620A Multiplexer module is similar to other multiplexers in Pickering range of switching modules except thermal EMF is substantially reduced to <1.5µV with 250nV thermal stability.
-
Product
PXI Waveform Generator
Waveform Generator
PXI Waveform Generators can produce precise waveforms including sine, square, triangle, and ramp as well as arbitrary, user-defined waveforms using sequences of data or streaming continuously from a host or peer-to-peer instrument within the PXI system. These instruments are ideal for tightly synchronized, mixed-signal test systems in scientific research or test of semiconductor devices, consumer electronics, automotive, and aerospace/defense.
-
Product
PXI Prototyping Module, 2-Slot, 9-Pin D-Type
40-225A-702
Prototyping Module
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
Product
PXI RF Analog Signal Generator
Signal Generator
PXI RF Analog Signal Generators deliver the functionality of RF signal generators to the modular, compact PXI form factor. These modules support frequency ranges from 250 kHz to 20 GHz. You can combine PXI RF Analog Signal Generators with other PXI modular instrumentation to design automated test systems for radar, RF integrated circuits (RFICs), and automotive test applications.
-
Product
PCIe Gen 3 ATCA Carrier Low-Power Xeon E3
ATC122
-
The ATC122 is a Carrier Module with an on board x16 PCIe Gen3 slot to accept any standard PCIe edge type module. The module has dual 10GbE connected to the Fabric channels and dual GbE to the base channels. It comes with 32 GB of ECC memory. It also has an option for Trusted Platform Management (TPM).
-
Product
High-performance PXI System
M5000 Series
-
The M5000 Series forms the backbone for the Keysight Quantum Control System (QCS) – complete digital solution that eliminates the need to design custom control solutions. Analog LOs and mixers in traditional hardware used for quantum control require frequent calibration, introduce leakage noise, and contribute to slow drifts in the performance of the system. The Keysight M5000 Series fully eliminates the need for these components leading to enhanced ease-of-use, unrivaled noise performance, and improved long-term stability.
-
Product
8 Slot, 3U, 350W, PXI Chassis
40-908-001
Chassis
This PXI chassis includes all the features and performance required by version 2.1 of the PXI standard and supports a control interface or embedded controller and up to seven more 3U peripheral modules.
-
Product
PXI Source And Measurement Unit Family
PXS840x
Source Measure Unit
The PXS(e)840x is a high precision, high speed source and measurement unit, which is designed for automated high throughput testing.
-
Product
PXIe8862, 2.6 GHz 8-Core PXI Controller
787987-01
Embedded Controller
The PXIe8862 is an Intel Core i7 8Core embedded controller for PXI Express systems. You use the PXIe8862 for processor-intensive RF, modular instrumentation, and data acquisition applications. The PXIe8862 includes two 10/100/1000/2500BASET (Gigabit) Ethernet ports, two USB 3.0 ports, four USB 2.0 ports, as well as an integrated hard drive, serial port, two Thunderbolt 4 ports, and other peripheral I/O.
-
Product
PXI Resistor Module 2-Channel 1.5R to 4.09k
40-293-023
Programmable Resistor Module
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Wideband Amplifier PXI Card
GX1222
Amplifier
The GX1222 is a 3U single-slot, PXI-based wideband power amplifier used for signal amplification purposes. Offering excellent fidelity, the GX1222 amplifies signals from DC to over 20 MHz with a fixed gain of x10. Custom gains are also available without compromising signal purity and amplifier performance.
-
Product
PXI Prototyping Module, 1-Slot, 15-Pin D-Type
40-225A-601
Prototyping Module
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
Product
PXI BRIC8 1Resource Distributor, 2Bus Matrix
40-569-112
Matrix Switch Module
The 40-569 PXI Matrix BRIC provides a range of high-density bus matrix inputs and resource distributor bussed configurations capable of switching up to 2A and up to 100VDC/70VAC. These large PXI matrix modules are available in 4 or 8 slot sizes and are constructed using high-quality electromechanical relays.
-
Product
Minority Carrier Lifetime Tester
HS-CLT
-
HS-CLT Minority Carrier Lifetime Tester has strong functions. It can not only measure carrier lifetime of wafer but also silicon ingot, silicon filament,silicon phosphorus ingot,silicon boron ingot, seed crystal and other irregular shape silicon material.The minority carrier testing ranges from 1μs to 6000μs, the minimum resistivity is 0.1Ω.cm, (can be extensive to 0.01Ω.cm). Dynamic curve monitoring in the whole process.
-
Product
Switch Card Carriers
-
Compatible for use on the VXI platform, these switch carrier products were formerly sold under the Racal Instruments brand name.
-
Product
PCI to PXI Remote Control Kit
41-921A-001-KIT
-
This kit provides a seamless connection between a control PC’s PCI interface and a PXI chassis. The PCI to StarFabric module (51-921A) resides in one of the controllers PCI slots and provides two independent StarFabric serial interfaces, each capable of driving a separate PXI chassis.
-
Product
PXI High Resolution Waveform Digitizer Family
PXD730x
-
The PXD730x High Resolution Waveform Digitizer family features up to two 100MS/s simultaneously sampled input channels with 16Bit resolution, input voltages up to ±60V and a bandwidth up to 50MHz. Every digitizer channel has its own 2MB memory which allows up to 1 million samples. Data can be acquired before and after the trigger event with a programmable sample counter, that controls the number of data points.
-
Product
PXI 64-Channel Digital Output Module
40-412A-021
Digital Output Module
The 40-412A-021 (PXI) and 42-412A-021 (PXIe) are 64-Channel Digital Output modules with high output voltage and current capability. The outputs can be used for high or low drive and each channel is capable of sourcing 0.5A from the high side or 0.5A sink on the low side. Accidental operation of both high and low side driver on the same channel is prevented by the supplied driver. Outputs are fully protected against over-voltage, over-current and thermal overload, ensuring robust and reliable operation in the toughest test environments. For high side driving, the voltage source is supplied externally, allowing the module to drive high capacity loads separate from the chassis power supply. For low side driving, the external source is not used and the module’s output operates an open collector or open drain driver.
-
Product
PXI 5A Power MUX, 2-Bank, 24-Channel
40-651-002
Multiplexer Module
This range of high density power multiplexer modules is suitable for switching inductive/capacitive loads up to 5A at 250VAC. It is available in the following 1-pole multiplexer formats: 1-bank 48-channel. 2-bank 24-channel. 4-bank 11-channel. 8-bank 5-channel. Connections are made via a front panel 50-way male D-type connector. Power multiplexer modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids.
-
Product
PXI-8517, 2-Port PXI FlexRay Interface Module
780689-02
FlexRay Interface
2-Port PXI FlexRay Interface Module—The PXI‑8517 is designed for developing FlexRay applications. As part of the NI‑XNET platform, the PXI‑8517 works well in applications requiring real-time, high-speed manipulation of hundreds of FlexRay frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The PXI‑8517 contains two fully functional FlexRay interfaces, allowing an individual ECU to be connected to the interface when other cold-start nodes are not available. You also can use the interfaces individually to connect two separate FlexRay networks while maintaining full performance on each interface.
-
Product
PXI 2A Multiplexer, 16-Bank, 8-Channel 1-Pole
40-614-001
Multiplexer Module
The 40-614 High Density 2 Amp multiplexer module is available in 20 configurations. All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 200VDC/140VACThe module is suitable for signal routing in ATE and data acquisition systems. User connections are made via a front panel 160-pin DIN 41612 connector which is fully supported by our range of cabling and connector solutions.
-
Product
PXI 16x SPST High Voltage Reed Relays
40-310-101
Reed Relay
The 40-310/320 Range of High Voltage Switching Modules will hot switch up to 750V peak and cold switch up to 1000V peak in either general purpose relay (40-310) or multiplexer (40-320) configurations. These modules contain high-quality reed relays with switching ratings comfortably higher than the 40-310/320 specification. Applications for the 40-310/320 series modules include; circuit board isolation testing, relay testing, semiconductor breakdown monitoring and cable harness insulation testing.
-
Product
PXI 3A Power MUX BRIC, 9-Channel, 16-Pole
40-571-203
Multiplexer Module
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
Product
PXI 64 x SPDT Electromechanical Relays
40-148-201
Relay
The 40-145/46/48 range of high density switching modules are available in Normally Open (SPST & DPST) and changeover (SPDT) configurations. Connections are made via a front panel 200 pin female connector. General purpose relays are suitable for the construction of small switching networks, I/O port switching, for slave switching larger relays or for operating external devices (e.g. lamps, solenoids etc.).
-
Product
PXI 2A Multiplexer, 1-Bank, 32-Channel, 4-Pole
40-614C-017
Multiplexer Module
This 1-bank, 32-channel, 4 pole version is part of the 40-614C High Density 2A multiplexer module range that is available in 20 configurations (see Also in this Range link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
PXI 24xSPST High Voltage Power Relay Module
40-330-001
Relay
The Pickering Interfaces 40-330 High Voltage Power Relay Module is suitable for applications requiring high voltage power relay switching with high density.It features current handling up to 5A, 1000VDC/1000VAC peak cold switching and 110VDC/250VAC hot switching. It is configured as a bank of 12, 18 or 24 separate Single Pole Single Throw (SPST) relays. Connections are made via a front panel mounted 50-pin (24xSPST) or 37-pin (18 and 12xSPST) high voltage D-Type connector.
-
Product
PXI 16 x SPDT Reed Relays
40-110-021
Relay
The 40-110/115 range of switching modules are available in both Changeover (SPDT) and Normally Open (SPST & DPST) configurations. Connections are made via a front panel 96 pin male micro-D connector. General purpose reed relays are used for the construction of small switching networks or for slaving up to larger switches.To simplify inter-relay wiring, interconnection points are built onto the circuit board thus easing the construction of complicated wiring.
-
Product
PXI Multifunction I/O Module
Multifunction I/O
The PXI Multifunction I/O Module provides I/O with varying numbers of channels, sample rates, and output rates with precise timing, triggering, and synchronization between models. This module can be used for industry applications such as laboratory research, design verification test, and manufacturing test.The PXI Multifunction I/O Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
