-
Product
Ball Pressure Test Device
ZBP-T
-
Made up by the related item according to IEC60695, IEC884-1, GB/T5169.21-2006, GB4706.1-2005, GB2099.1-2008, etc. • R = 2.5mm Pressure: 20N • Base with thermocouple hole • Material: 304 stainless steel
-
Product
Differential Pressure Flow Meters
-
Engineers can rely on the V-Cone dp flow meter to make life easier. McCrometer’s differential pressure flow meter is the versatile, highly compatible flow measurement solution for a variety of industries. When accuracy and repeatability are critical, the V-Cone’s performance brings superior value.
-
Product
Intelligent Pressure Calibrator
-
Huaxin Instrument (Beijing) Co., Ltd
Here at Huaxin, we offer a selection of HS602 and HX601B intelligent pressure calibrators. They are high pressure, single range digital pressure calibrators with HART communication capability. Composed of high precision measurement chip, 24V DC power supply, battery charging protection circuit, HART communication module and intelligent digital pressure module, these two pressure calibrators provide a pressure calibration solution for gauges, transmitters, and switches over a wide pressure range.
-
Product
Heat-Resistant Test Equipment Ball Pressure Tester
CX-Q002
-
Shenzhen Chuangxin Instruments Co., Ltd.
Ball Pressure Tester is used for testing parts of non-metallic materials for resistance to heat. It is applicable to electrotechnical equipment, its subassemblies and components, and to solid electrical insulating materials except ceramics.
-
Product
Handheld Gauge for Nondestructive Coating Thickness Measurement
PHASCOPE PMP10
-
The most experienced device in our tactile portfolio – reliably solves all special applications.
-
Product
Pressure Controllers For Closed Volumes
-
Alicat Scientific, Incorporated
Use dual-valve pressure controllers to measure and control absolute, gauge, or differential pressure in closed volumes. Pressure controllers are accurate to ±0.25% of full scale, with a measurement range from 0.01-100% of full scale.
-
Product
Multifunction Engine Gauge
1U417-series
-
The three essential engine parameters are packaged in a 3” instrument. The 1U417 was derived from the Garwin 22-804 and is a direct replacement. As evidenced by its predecessor, the three most essential engine parameters have traditionally been the most requested by our customers.
-
Product
Pressure Insensitive Mass Flow Module
Criterion D500
-
This leading-edge pressure insensitive mass flow module is installed with differential pressure detection and a piezo actuator valve.
-
Product
Fuel Pressure Testers
-
• Developed with input from technicians on adaptor selection for 7.3 L, 6.7 L, 6.4 L and 6.0 L Ford®Power Stroke®engines• 0 100 PSI gauge and hose assembly• Low-pressure diesel-fuel delivery testing (lift pump)• Correct fuel delivery and dynamic fuel pressure are crucial to having a properly running engine• Helps prevent a lean condition that may cause burning of injectors or scorched cylinders• Convenient protective slide-lid case that will fit in a 4" drawer for easy tool access• Technical Support: 1-866-713-6007
-
Product
Head-separated Dual Display Digital Pressure Sensor [For Gas]
DPH-100 / DPC-100
-
Panasonic Industrial Devices Sales Company of America
Single-Axis Type Digital Pressure Sensor With Optional Dual 3-Color Display
-
Product
Diaphragm Operated Pressure Switch
1000E
-
Extremely rugged construction provides excellent reliability in chemical, petroleum and industrial plants. Bellville spring movement permits mounting of control in any position and helps prevent contact chatter. new design also provides high overpressure protection. Available with standard weatherproof housing to meet NEMA-1 through 4X and NEMA-13, JIC.
-
Product
Electronic Pressure Switch (select Pressure Switch)
PSW
-
multi-rotation trimmer and operation display are built in, making setting easy.
-
Product
Barometric Pressure Sensors
-
Accurate within 1.5 % across a pressure range of 15 to 115 kPa (4.43 to 34.96 in Hg). Long-term non-stability has been measured continuously indoors and in natural conditions (with sensors mounted inside a datalogger enclosure) for multiple sensors and is less than 0.5 % per year. Temperature effects on signal are less than 1 % across a wide temperature range (-20 to 50 C).
-
Product
Pressure, Strain And Shock Data Loggers
-
Dataloggers for pressure, bridge input for strain or load measurement and also tri-axial shock dataloggers with built in accelerometers.
-
Product
Pulse Start Generator for High Pressure Sodium Lamp
LPSG60662
-
The start-up test of the special lights pulse start generator is for lighting class industry such as high pressure sodium, it is according to IEC60662: 2011 and GB/T13259-2005 standard requirements.
-
Product
Film and Paper Thickness Gauges
-
Economical, Accurate, Easy-to-Operate, our line of off-line paper / film thickness gauges are manufactured to meet TAPPI specifications for paper or ASTM specifications for film.
-
Product
Gauge Type T Thermocouple Wire
W-TW-44TEF
-
Most thermocouple wire used in the manufacture of sensors is "Special Limits" wire which, to meet NIST standards, must be accurate to 0.5°C in the range 0-50°C. This means that even with most sophisticated electronics, the best possible accuracy for the system is 0.5°C.
-
Product
Tool, Inspection Depth Gauge, Micro Coax, Receiver
910121179
Inspection Tool
Tool, Inspection Depth Gauge, Micro Coax, Receiver
-
Product
Very Low Pressure Variable Reluctance Sensor
DP103
-
The Validyne DP103 is designed for exceedingly low differential pressure measurement applications where high accuracy is required under rough physical conditions. With full scale ranges down to -0.008 psid (-0.56cm H2O), this instrument is being used in the measurement of very low flow rates of gases where symmetrical pressure cavities are required for dynamic response. It is also used in very small leak detection and pressure null detection systems.
-
Product
Pressure Transducers with USB Interface
P61
-
The Validyne model P61 is a digital differential pressure transmitter designed for industrial pressure measurement applications. The on-board microprocessor provides high accuracy and improved stability in changing thermal environments. Communication and power via USB interface provides remote zero and span adjustment as well as digital pressure readings in engineering units. Drivers and software for the USB interface are included.
-
Product
SICRAM Module Pressure Probes
PP471
-
Module to connect pressure measuring instruments to pressure probes.
-
Product
Digital Differential Pressure Manometer
Si-PM3
-
The palm-sized Sauermann Si-PM3 digital differential pressure manometer easily measures pressure.
-
Product
Low Differential Pressure Switch -
1800
-
Essential for industrial environments, the Series 1800 combines small size and low price with 2% repeatability for enough accuracy for all but the most demanding applications. Set point adjustment inside the mounting stud permits mounting switch on one side of a wall or panel with adjustment easily accessible on the opposite side. UL and CSA listed, and FM approved.
-
Product
Torque Gauges
-
Mark-10 torque gauges and torque testers are accurate and feature-rich torque measurement products ideal for a wide range of torque applications. All torque gauges and torque testers capture the peak torque in both directions (CW and CCW) and have selectable units of torque measurement. Torque capacities are available from 10 ozFin full scale to 5,000 lbFin, depending on the torque gauge or torque tester. Units may be handheld or used with a test stand and gripping fixtures to create a complete torque testing solution. All torque gauges and torque testers carry the CE mark.
-
Product
Ball Pressure Test Apparatus
-
The Ball Pressure Apparatus is designed to perform test specified in IS Standard where resistance of insulating material to elevated operating temperature is to be determined. It is used to test insulation materials used in Electrical Appliances, Electrical wiring accessories, luminaries, motors, connectors, etc. It is a precision engineered test instrument for use by safety and compliance testing laboratories.
-
Product
Premium Wireless Vacuum Gauge Probe for use with HUB8 or HUB6
WVG2
-
UEi Test & Measurement Instruments
Premium Wireless Vacuum Gauge Probe
-
Product
Differential Pressure Transmitters
-
The differential pressure transmitter portfolio from ABB offers a broad variety of communication possibilities. Another highlight of our sensors is the measurement accuracy up to 0.025 %.
-
Product
EMAT Thickness Gauges
-
The EMAT thickness gauge uses advanced electromagnetic-acoustic technology to measure metal thickness, even in cases where traditional methods like piezo-ultrasonic or laser-optical are not applicable.
-
Product
Carbon Fibre Beam Gauge
-
Designed to measure both internal and external diameters and lengths, the high modulus carbon fibre beam is stiff, lightweight and has an extremely low co-efficient of thermal expansion (CTE). Suitable for measuring high accuracy diameters and lengths up to 4000mm+.
-
Product
Pressure Meters
-
General's line of pressure meters and manometers. The top-of-the-line pressure meter is the data logging PM930SD Pressure Meter, which can measure up to 400 bar (5800 psi) when mated with an optional sensor. By comparison, the measurement range of the DM82XX family of manometers tops out at 100 psi. Also in this sub-category are the GPKXXX family of analog gas pressure test kits and the analog HG15 Hydrogage Manometer.
