Differential Amplifiers
Increase the voltage of multiple input signals to proportionate outputs.
-
Product
1 GHz 60 V Common Mode Differential Probe
DL10-HCM
Differential Probe
60 V of common mode and 80 V differential input range with 1 GHz of bandwidth, make these probes ideal for lower voltage GaN power conversion measurements. The 60 V of common mode is well suited for handling any float of the battery and bulk/absorption voltage during charging, while the 80 V differential input range provide margin for any overshoot.
-
Product
RGB Digital Fiber Optic Amplifier
CZ Series
-
RGB Digital Fiber Optic Type. RGB three-light source. Wide detection range of up to 7020 mm. High-speed response of 300 s. Water-resistant sensor head IP-67 rated
-
Product
Ground-Based Satcom Amplifiers, Modems & More
-
Modems for Small-to-Medium Sized Networks Where Security is of Utmost Importance.
-
Product
40mA One-Channel Amplifiers
-
Piezo amplifiers/controllers are designed for high precision low to mid-speed positioning of low-voltage piezo actuators. These amplifiers are tuned for extremely high output stability and extremely low signal noise at the output. A low amplifier signal-to-noise ratio is very important because it determines the total resolution of the actuator. The nearly unlimited resolution of piezo-electric actuators using these amplifiers results in ultra-precise movement.
-
Product
Low Voltage DC / Battery Powered HV Amplifiers
WMA-01 And WMA-01LF
-
The Falco Systems WMA-01 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 3mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-01LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.1mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
Product
High Voltage Differential Probes
-
A high voltage differential probe is used for measuring the voltage difference between two test points where neither test point is at ground. High voltage differential probes from Tektronix can be used for signals up to 6000 V. These probes are the best choice for making non-ground referenced, floating or isolated measurements in large part due to their common mode rejection capability. These products are designed, manufactured, and serviced by Tektronix.
-
Product
PWM Amplifiers
SA Series
-
Covering a power range of 5 to 20 KVA, the MCS line of high frequency PWM servo amplifiers utilizes the latest in solid state power circuitry and power devices to provide the greatest amount of flexibility available in the brushless motor drive market. The SA Series is a stand alone system with integral power supply designed for industrial application where the system will mount inside a NEMA type enclosure.
-
Product
150 kHz-230 MHz Broadband Power Amplifiers
-
Output power up to 80W for standard conducted immunity testing. Our 150 kHz-230 MHz amplifier range covers output power ranging from 20 W to 80 W.
-
Product
5B Measuring Amplifiers
MA Series
-
Highest aim of our connection technology is user-friendliness. Very comfortable is the connection of our products to the most various sensors and signals.
-
Product
Communications/Data Link Amplifiers
-
Amplifiers specific to the Communications systems include a wide range of Solid State Power Amplifiers (SSPAs) and Low Noise Amplifiers (LNAs) originally from Paradise Datacom and a range of organically developed products within TMS. Satcom SSPAs are considered a core competence of Paradise Datacom's product line who have invested heavily in converting it's complete amplifier offering from GaAs to GaN from C-Band all the way to Ka-Band.
-
Product
Lock-in Amplifier
Signaloc
-
Designed for use in Hinds’ Exicor Systems the Signaloc is now availaible for anyone who can use a dual-phase, analog, single frequency lock-in amplifier.
-
Product
Gas Permeability Tester with Differential Pressure Method
GPT-203
-
GPT-203 Gas Permeability Tester is based on the differential pressure method and is professionally applicable to the determination of permeance and permeability of plastic films, composite films, high barrier materials, sheeting, metal foils.
-
Product
Dual Channel High Voltage Linear Amplifier
F20AD
-
This unit contains two independent F20A amplifiers that share common ground reference and power supply.
-
Product
High-end Cable DAC & Amplifier
Impacto universal
-
Beyerdynamic Digitalize high-end headphones.
-
Product
Medium-Power, Broadband Amplifiers
-
Our family of distributed amplifiers utilize advanced broadband design techniques to achieve solid performance in gain, flatness, noise figure and output power over a wide frequency range. The experienced design team has the know-how and tools available to take any standard product and customize it for your specific application.
-
Product
Analog Control Variable Gain Amplifiers (VGAs)
-
Analog Devices voltage controlled variable gain amplifiers provide continuous gain control over a wide dynamic range for a variety of audio and optical frequency bands. Our VGAs improve the dynamic range of a circuit by allowing users to adjust a signal’s amplitude in real time, which is invaluable for ultrasound, speech analysis, radar, wireless communications, and instrumentation-related applications.
-
Product
RF Benchtop / EMC Amplifier (110/220V)
-
RF-Lambda is a world leader in the design and manufacture of high-power, solid-state, broadband AC-powered EMC power amplifiers.
-
Product
RF Benchtop / EMC Amplifier
-
RF-Lambda is a world leader in the design and manufacture of high-power, solid-state, broadband AC-powered EMC power amplifiers.
-
Product
Distribution Amplifiers
-
A complete range of distribution amplifiers are manufactured by Precision Test Systems. A distribution amplifier is used to distribute the output of a frequency reference to many different places. Usually the frequency is 5 or 10 MHz but we manufacture distribution amps from DC to over 2000 MHz. We make some of the industries lowest phase noise products.
-
Product
Isolation Amplifiers
-
Knick Elektronische Messgeräte GmbH & Co. KG.
Unipolar and bipolar DC input signals 20 mV to 200 V and 0.1 mA to 100 mA calibrated range selection. Working voltage up to 1000 V AC / DC.
-
Product
8 Channel Fast Amplifier
V975
-
The Mod. V975 is an 8 channel fast rise time amplifier housed in a 1-unit VME module; each channel features a fixed voltage gain of 10. Channels are bipolar, non-inverting and can be cascaded in order to obtain larger gain values. Input bandwitdth is 250 MHz for signals up to 50 mVpp and decreases for larger ones (up to 110 MHz @ 400 mVpp). Each channel is provided with three LEMO 00 connectors, one for the input and two bridged for the output.
-
Product
Fiber Transmitter With Fiber Amplifier
FTFA 844
-
- Auto Switch over from Fiber to RF & Vice versa- Works as Transmitter & Fiber Amplifier- AGC / MGC - Automatic & Manual Gain Control- Very High MER / BER- High Quality DFB Lasers with Isolators- RF Input : 78dB ~ 90dB- Optical Input : -8dBm ~ +2dBm- Optical Wavelength : 1310nm- Power : 110VAC ~ 240VAC, 50HzSpecifications:- Bandwidth: 47 ~ 860 MHz- Input RF Level: 75 ~ 85dBuV- Input Optical Level:- -8dBm ~ +3dBm- SMPS Power Supply:- 110V AC ~ 265V AC- Power Consumption: 50Watt- AGC Range: 0 ~ -8dBm
-
Product
Measurement Amplifier In Rugged IP65 Housing
-
INELTA Sensorsysteme GmbH & Co. KG
For DMS Force Sensors and LVDT
-
Product
In-Line Charge Amplifiers
-
The in-line charge amplifier is used to excite structures or machinery with a definable impulse force. Resonances are identified by impulse, an important measurement parameter for the study of dynamic behavior. The 4705A1 is a fast turn on time, 50 mV/pc, in line charge amplifier with BNC jack connectors on each side.
-
Product
Accessory Kit for High Voltage Differential Probe
PK-HV-001
Differential Probe
Accessory kit for High Voltage Differential Probe
-
Product
Long Spring Ground for ZD Differential Probe Qty 2
PACC-ZD003
Differential Probe
Long spring ground for ZD differential probe Qty 2
-
Product
6 GHz ProBus2 Differential Probe with Dx10-SI Solder-In Tip
D610-A-PB2
Differential Probe
- Choice of 4 GHz or 6 GHz bandwidth models- Up to 5 Vpk-pk dynamic range with low noise- ±3 V offset range- Low loading and high impedance for minimal signal disturbance- Ideal for DDR2, DDR3, LPDDR2- Deluxe soft carrying case- Innovative QuickLink architecture- Wide variety of tips and leads-- Solder-In Lead-- Optional Positioner (Browser) Tip-- Quick Connect Lead-- Square Pin Lead-- HiTemp Solder-In Lead
-
Product
Low Noise Op Amplifiers (≤ 10nV/√Hz)
-
Analog Devices’ portfolio of low noise (≤ 10nV/√Hz) op amps includes many amps with the lowest noise performance in the industry. These high speed, low distortion (1 nV or less) op amps enable better signal fidelity in the most demanding conditions, allowing system designers to achieve the lowest total system noise performance in applications with high source impedances. We feature a considerable variety of these amps with wide supply ranges and low power.
-
Product
DIO-AIO Conversion Set For Conventional Power Amplifier
PAD64
-
PAD64 DIO(digital input/output)-AIO(analog input/output) Converter is the equipment which could be used for DI/DO (Digital input/Digital output) conversion and galvanic isolation between Real-time simulation system and protection equipment, and any other equipment which need AIO (analog binary input/ output, dry contacts).
-
Product
Parallel Differential Battery Tester With Integrated Chamber
-
Accelerate your battery parallel test using our PDBT. Featuring an integrated chamber, it precisely conducts battery comparison test and fast measures battery's self-discharge current. Its portable, powerful design is perfect for innovative research applications.
