Differential Amplifiers
Increase the voltage of multiple input signals to proportionate outputs.
-
Product
General Performance Differential Pressure Transducers
-
These general performance Baratron® differential capacitance manometers measure the difference in pressure between the inlet tube and the reference cavity. The reference cavity can be connected to any pressure or vacuum source, or be open to local atmosphere.
-
Product
Limiting Amplifiers
-
Advanced Science and Novel Technology, Co., Inc.
Broadband (DC-28Gbps) limiting amplifierExhibits low jitter and limited temperature variation over industrial temperature range100MHz of bandwidth for the amplitude adjustment tuning portIdeal for high speed proof-of-concept prototypingFully differential CML input interfacesFully differential CML output interface with adjustable SE amplitude from 0V to 1.0VSingle +3.3V or -3.3V power supplyPower consumption: 660mWFabricated in SiGe for high performance, yield, and reliabilityCustom CQFP 24-pin package
-
Product
Gas Differential Pressure Switch
A4
-
Rugged Series A4 Differential Pressure Switch offers field adjustments and can handle system pressures up to 6000 psig. Piston design allows mounting in any orientation. The switch is capable of carrying moderate shock and vibratory loads
-
Product
Compact Differential Pressure Transmitters
Series 668B/D
-
Our low cost SERIES 668B/D Compact Differential Pressure Transmitters are capable of sensing differential gage pressure with ±0.8% FS accuracy, and converts this pressure difference to a proportional high level analog output for both unidirectional and bi-directional pressure ranges. These transmitters can withstand up to 15 psig overpressure with no damage to the unit. The compact, lightweight design makes installation simple and easy. Units are protected against incorrect wiring, and include a protective terminal cover.
-
Product
Bridge Amplifier
90376
-
This miniature, on-board, transducer amplifier is capable of supplying excitation voltage and amplifying millivolt signals from strain gage based transducers.
-
Product
High Voltage Differential Probes
-
High voltage differential probes provide high CMRR over a broad frequency range (up to 400 MHz) to simplify the measurement challenges found in noisy, high common-mode power electronics environments. The probe’s design is easy-to-use and enables safe, precise high voltage floating measurements.
-
Product
Overdrive Protected Amplifier
-
RF Lambda’s line of overdrive protected amplifiers incorporate a technology which eliminates the need for a limiter to protect the amplifier from damage. High input powers up to 10W can be injected in the amp without damage. Hermetically sealed options are available upon request.
-
Product
Amplifier Systems
-
Sutter Instrument provides a complete line of electrophysiology recording hardware and software, ideal for applications ranging from tissue slice patch clamp over dissociated cell recordings to cell line studies.
-
Product
5B Measuring Amplifiers
MA Series
-
Highest aim of our connection technology is user-friendliness. Very comfortable is the connection of our products to the most various sensors and signals.
-
Product
Millimeter-Wave Amplifiers
-
When your application requires operating at Ka-band and above, trust Mercury Systems’ millimeter wave amplifiers to perform. With standard designs up to 65GHz and custom products available, Mercury is ready to support your high frequency requirement.
-
Product
Differential Pressure Meters
-
These differential pressure meters contain many characteristics that can be found i Differential Pressure Meters for measuring differential pressures of gases and liquids in the industrial sector, in medical engineering and meteorologyn modern measuring instruments such as data hold function, LCD or LED display, internal memory and the ability to transfer data to a computer and software for processing measurement values. Some models come with an analogue output.
-
Product
Universal Amplifier Heatsinks
-
A universal heatsink, which is designed and fabricated for Eravant's active device applications with up to 15-watt power dissipation. The heatsink consists of the main heatsink body, a DC fan and a heat spreader. The heat spreader is also known as adapter, which is used to bridge the mounting gap between the heat sink main body and the to-be-heat-sunk devices, such as power amplifier, frequency active multiplier, oscillator, transmitter and transceiver due to various mounting hole locations. The heat spreader offers various mounting patterns to accommodate more than 15 product models. This heatsink is not only designed for Eravant's standard products and Uni-Guide™ featured products, but also for many industrial standard microwave and millimeter wave products offered by other manufacturers. Other heatsinks with different power dissipation capacities are offered under different model numbers.
-
Product
Zero-Drift Op Amplifiers
-
The zero-drift amplifiers from Analog Devices combine both auto-zero and a chopper to self-correct continuously for dc errors over time and temperature, enabling the amplifier to achieve microvolt-offsets and nanovolts per degree Celsius drift. By design, the zero-drift amplifier has no 1/f noise nor does it suffer from long-term drift.
-
Product
Modulated Wideband Driver Amplifier
TBMDA2
-
The TBMDA2 modulated wideband driver amplifier is designed in order to create an inexpensive signal source for immunity testing of electronic building blocks and products. It is designed to be driven by the tracking generator output of spectrum analyzers. With its 1dB compression point of +27dBm, it can boost the output power of a tracking generator up to 500mW.
-
Product
Low Differential Pressure Switch
1900
-
Our most popular series combines advanced design and precision construction to make these switches able to perform many of the tasks of larger, costlier units. Designed for air conditioning service, they also serve many fluidics, refrigeration, oven and dryer applications
-
Product
Bi-Directional Amplifiers
-
Fairview’s bi-directional amplifier models are designed for use in both commercial and military applications and will support any signal type and modulation format such as 3G and 4G telecom, WLAN, OFDM, DVB and CW/AM/FM. Fairview’s bi-directional amplifiers offer high power density, efficiency and linearity in small lightweight environmentally sealed packages with SMA connectors. These units also feature a quick-connect circular locking connector for DC and control functions and each design uses a single voltage supply with voltage regulation.
-
-
Product
Amplifier Modules Broadband
-
Modules are usually smaller and are usually part of systems. You supply your own DC voltage, make the connections and supply your own DC supply. Modules are available with or without heatsinks and fans. Amplifiers Modules are available in both Broadband and Band-Specific frequencies. Modular design concepts save time and money, and are lightweight, reliable, cost-effective solutions. We are well-known in the industry for successfully adapting our amplifiers or custom designing new solutions to suit each unique project. Please refer to our Adapted & Custom Design Solutions link to begin formulating your performance objectives and other criteria.
-
Product
Variable Constant Differential Flow Controller
VCD 1000
-
The Porter Model VCD 1000 flow controller is precision-engineered to control low gas flows at constant mass flow rates regardless of changes in downstream pressure.
-
Product
System Amplifiers
-
The perfect combination of high performance, wide bandwidth and low noise
-
Product
RF Power Amplifiers < MMICS
-
Macom Technology Solutions Holdings Inc.
MACOM is continually enhancing and expanding its MMIC power amplifier product portfolio to meet customers’ demanding technical challenges by leveraging state-of-the-art foundry technologies and proprietary in-house processes. MACOM partners with today’s leaders in Test and Measurement, SATCOM, Aerospace and Defense, Public Safety Radios, Wired Broadband, and Industrial Scientific and Medical applications to deliver industry leading, high-performance MMIC solutions in bare die and high performance packaging.
-
Product
High Voltage Amplifier
HA-405
-
* 400Vp-p(±200V DC)* 400mAp-p(±200mA DC)* Bandwidth: ≦1MHz(200Vp-p) *Slew Rate: 500V/us *Gain(AMPL):0~90(10 Turn VR) *DC Offset: ≦0~±200V(10 Turn VR+SW) *Output Resistor: 50Ω *Microprocess Control Protection
-
Product
VCOM Amplifiers And Calibrators
-
Renesas offers various VCOM amplifiers including rail-to-rail input-output operational amplifiers and rail-to-rail input-output buffers, as well as programmable VCOM calibrators that are ideal for display applications.
-
Product
Power Amplifier
-
The Model LN power amplifiers offer extended output power, voltage capabilities, lowdistortion, versatility and the latest BJT power in the operational amplifier technology. All theseperformance features are not available in other power amplifiers.
-
Product
Pressure Transmitters and Differential Pressure Transmitters
-
Fuji Electric has long delivered electronic transmitters, incorporating the micro-capacitance silicon sensor, to our customers worldwide.The FCX-AIII series transmitters feature compact design, high accuracy and performance, long-term stability. They also offer wide measuring ranges and provide a variety of diaphragm materials.
-
Product
RF POWER AMPLIFIERS
BLWA Series
-
A) RF-Sample PortsI) 3x 208 V AC / 60 HzB) External Dual Directional CouplerL) LAN Remote ControlC) IEEE-488.2 GPIB Remote ControlS) Internal RF Switching UnitD) Front Panel RF ConnectorsR) RS-232C Remote ControlE) RF Power Indication (digital)U) USB Remote ControlF) Gain AdjustmentW) Liquid CoolingH) DC SupplyX) External Control of other Amplifiers
-
Product
Power Amplifiers
-
Triad’s line of RF and microwave Power Amplifier modules for extended range amplified radio applications set the bar for efficiency, linearity, and size-to-power ratio. We have designed hundreds of COTS modules for exacting frequencies up to 40 GHz . They offer high power levels into the hundreds of watts. And if a standard RF/microwave amplifier design does not fit your exact requirements, we’re specialists in creating custom-modified versions of any of our COTS power amplifier modules.
-
Product
Panel-mounted Power Amplifier
PAC2000B
-
PA series amplifiers are specially designed for power network real time simulation applications,which requires large power output,high accuracy even at high current output for all kinds of load.
-
Product
Sound Source And Power Amplifier
-
Designed for acoustic application, with strong signal transmission capability and flexible measurement.
-
Product
Dining Isolation Amplifier
-
Knick Elektronische Messgeräte GmbH & Co. KG.
To feed and Isolation of 2-wire transmitters / sensors or SMART transmitters with HART transmission. Working voltage up to 2500 V AC / DC. Available for hazardous and non-hazardous area.
