Audio Amplifiers
This topic is for test equipment that is designed for the testing of audio amplifiers.
See Also: Amplifiers, RF Amplifiers, Preamplifiers, Current Amplifiers, Voltage Amplifiers, Transconductance Amplifiers, Op Amps, Klystron, Instrumentation Amplifiers, Distribution Amplifiers
-
Product
Audio
-
ams provides Active Noise Cancelation (ANC) solutions and also offers power and communication interfaces for smart earbuds
-
Product
Audio Loudness Monitoring And Logging System
-
The Mividi® Audio Loudness Monitoring and Logging System (Loudness Logger) provides a cost-effective solution for broadcast compliance monitoring and logging. It is a Windows PC based system that supports audio decoding, loudness monitoring and logging, log file management and playback. It takes transport stream input from UDP over IP or ASI interfaces, as well as Internet OTT streaming input using HLS, RTMP, RTSP, and MPEG-DASH protocols. A single system can support continuous monitoring and recording over 50 channels simultaneously.
-
Product
Distribution Amplifier
-
AVLINK TECHNIC TAIWAN CO., LTD.
Is a device that accepts a single input signal and provides this same signal to multiple isolated outputs.These devices are important because they allow a signal to be distributed to multiple destinations without ground loops or signal degradation. They are used for a number of common engineering tasks, including multiple amplification, cable television, splitting monitor and front of house mixes, and "tapping" a signal prior to sending it through effects units to preserve a "dry" signal for later experimentation.
-
Product
High Power Amplifiers
-
Solid State Power Amplifier (SSPA) technology continues to offer opportunities to displace Travelling Wave Tube Amplifiers (TWTA) from radar, communication and Electronic Warfare (EW) applications.
-
Product
mAEStro Audio Analog to Digital Converter
-
The mAEStro AADC-100 accepts balanced stereo analog audio inputs and converts them into a single digital bit stream in compliance with the AES/EBU (AES3) and S/PDIF digital audio standards. It generates 24-bit values and uses 128 times over-sampling for extremely accurate and linear analog to digital conversion, as well as offering a high dynamic range with exceptionally low total harmonic distortion and noise.
-
Product
Ka-band Power Amplifier (33-37 GHz, 10 Watt Output Power)
-
*Frequency band, GHz: 33-37 *Output power, typical, W: 10 (40 dBm) *Gain, dB, typical: 30*Gain flatness: 2 dB Max *Pulse width, Max.: 100 nanoseconds - 60 microseconds *Pulse reptition frequency: up to 100 KHz *Oprating temparture: -40 deg. Celsius to 60 deg. Celsius *Dimensions: 245 mm x 124 mm x 30 mm
-
Product
3.5" Embedded SBC With AMD G-Series APU, AMD A50M, LVDS/DisplayPort/VGA, Dual LANs And Audio
CAPA110
-
Axiomtek's CAPA110, a high-end graphics 3.5" embedded board is equipped with the latest AMD G-series APU dual core T56N 1.65GHz and AMD FCH A50M chipset, which is a wonderful choice for graphics-intensive applications such as high-end medical imaging, digital signage, kiosks/POI, thin clients, and gaming machines. One SO-DIMM socket on the CAPA110 supports up to 4GB of DDR3 1333 memory. The integrated Radeon™ HD6320 graphics controller delivers unprecedented high definition visual experience and offers outstanding 3D performance with DirectX 11 supported. Dual display capability is supported via the VGA and DisplayPort connections on the coastline, as well as onboard 18-bit/24-bit LVDS interface. Besides, the CAPA110 provides high-bandwidth expansion capability with one PCI Express Mini card for custom system configurations. Moreover, the system only requires +12V DC power input.
-
Product
3.5” Embedded SBC With Intel® Atom® X5-E3940 Processor, LVDS, HDMI, 2 GbE LANs And Audio
CAPA310
-
The CAPA310 features the onboard quad-core Intel® Atom® x5-E3940 processor (codename: Apollo Lake). The fanless small form factor embedded board is highly reliable with an extended operating temperature range of -40°C to +80°C and a wide range power input of 12V to 24V DC. This industrial-grade 3.5-inch embedded board is feature-rich and expandable, with stunning graphical performance. The CAPA310 is a highly versatile platform designed for Industrial IoT and intelligent systems such as industrial automation, self-service terminals, digital signage, POS/kiosk displays, medical, and more. To ensure flexible configuration and expandability, the CAPA310 has an emphasis on expandability with a full-size PCIe Mini Card slot and an optional ZIO connector for additional PCIe, LPC, USB and SMBus. Additionally, this compact embedded board features the Intel® integrated Gfx graphic engine to deliver high-resolution HD support for display interfaces: HDMI, LVDS and optional VGA. It is perfectly suited for gaming and signage applications.
-
Product
FTTx PON Optical Amplifier (1540~1563nm)
HA5800C (3RU)
-
Hangzhou Huatai Optic Tech. Co., Ltd.
HA5800C (3RU) series is a low noise, high performance, FTTP high power, multi-ports optical amplifier with gain spectrum band within 1540~1563nm. Each output port for optical amplifier has built-in well-performed CWDM. Every external up-link optical port of optical amplifier can connect with OLT PON port very conveniently. Each 1550nm (CATV)'s output optical port multiplex 1310/1490n's data stream, in order to reduce the quantity of the component and improve the index and reliability of the system.
-
Product
Motion Control Terminal Board For Panasonic MINAS A4 Servo Amplifiers
DIN-814-A40
Terminal Board
- Panasonic MINAS A4 super servo- Dimensions: 123 mm x 107 mm x 44 mm (WxLxH)- Available for PCI-8174, PCI-8164, PCI-8154, PCI-8158 and PCI-8134
-
Product
Standard & High Speed Amplifiers
-
Advanced Energy's Trek high voltage power amplifiers employ unique and proprietary circuitry. Benefit from closed-loop amplifier systems that feature exceptional DC stability and excellent wideband performance characteristics. And thanks to all-solid-state designs, our amplifiers are protected from output short circuits and overvoltages.
-
Product
4x4 VGA + Audio Matrix Switch with UTP Output and IP Control
VSM-I-A-4-JA4
-
Switch up to 4 VGA inputs to 4 VGA outputs with independent audio routing. Additional RJ45 output connectors provide extended output up to 1000 ft (305 m) over a single UTP cable (with compatible URA receivers). 550 MHz bandwidth supports resolutions beyond 1920x1200.
-
Product
DSP And Power Amplifier
DMPA12
-
The DMPA12 is a powerful digital audio processor and multi-channel power amplifier combined into a single rack space component designed to work with DM Series processors. The design represents a milestone in DSP technology in its basic architecture and in its processing speed and efficiency. The primary applications are sound reinforcement and teleconferencing in boardrooms, courtrooms, worship centers, distance learning systems, hotels and other applications with multiple microphones and loudspeakers. The design is ideally suited to mix-minus sound reinforcement systems.
-
-
Product
Saluki SE1022D DSP Lock-In Amplifier (Dual-channel)
-
SE1022D Digital Lock-in Amplifier provides an excellent performance within its bandwidth from 1 mHz to 102 kHz. More importantly, SE1022D has dual independent input channels and dual independent high precision signal generators. Each input channel and signal generator can be used independently which means that the SE1022D is equivalent to two traditional lock-in amplifiers. Moreover, due to the twin symmetrical design, the two independent input channels and signal generators have ultra-high synchronicity, which meets the measurement requirements demanding extremely high synchronization.
-
Product
SMARC V1.0 SoM Evaluation Kit With Quad/DualLite 800 MHz (Industrial) SoC,1GB Memory, 4GB EMMC, Gigabit Ethernet, Audio, CAN, MIPI And PCAM
SCM120-120-EVK
-
*Ultra low power consumption Cortex™-A9*2 CAN 2.0B*24-bit TTL LCD*LVDS/HDMI 1080P*10/100/1000 Mbps Ethernet*Open GL ES2.0*Linux3.0.35/Android 4.3*Audio
-
Product
Audio Panel/Amplifier Test Fixture
TA-200
-
The Model TA-200 test panel was designed to allow Avionics shops the capability to test and troubleshoot both today's new generation audio panels as well as the standard audio panels of the past. The testing of these panels over the years has always proven to be a very time consuming job for most shops because of the limited capabilities of any past test panels.
-
Product
Operational Amplifiers
Op Amps
-
For designs requiring operational amplifiers (op amps), Analog Devices' portfolio of high speed op amps and precision op amps provides a broad choice of products that deliver unmatched performance. Explore op amps by parameters, and find expert system-level advice on design problems with our amplifier reference designs (Circuits from the Lab®), design tools, selection guides, calculators, and SPICE models.
-
Product
Signal Generator, Audio, Compact, Handheld, 1 Channel, 20kHz, FM, US Plug
72-490
-
Highly versatile compact audio generator is perfect for sound system and speaker component testing. Its high precision and remote VCO input make it suitable for the serious test environment, yet its compact size and low cost make it suitable for any tool box. This device is designed to be connected to the line level of any consumer or commercial designed audio amplifier. While it is designed to be used with unbalanced inputs, it is also suitable for balanced equipment
-
Product
Load Cell Amplifier Signal Conditioner with DB9 Connectors
MODEL LCA-9PC
-
The LCA-9PC Module provides low-cost, dedicated signal conditioning for a single bridge type load cell or torque sensor. Model LCA-9PC comes with DB9 male and female connectors, which require soldering to user-furnished mating female or male wire connectors. On- board jumper selections include sensitivities from 0.5 mV/V to 10 mV/V, bandwidths from 100 Hz to 30 kHz, and amplified outputs of 0 to ±5V, 0 to ±10V, 0-16 mA, 0-20 mA or 4-20 mA. Zero and span adjustments are via precision 25-turn low-tempco metal film otentiometers.The units can be operated next to the sensor with 4-wire hookup or at distances up to 1 km (3300 feet) with 6-wire hookup. An onboard 87.325 kΩ resistor allows easy shunt calibration at the push of a button. Provision is also made for a user-furnished calibration resistor. Power requirements are 11.8 to 26V DC with load currents from 10 to 60 mA, the latter applying when the unit provides 10V DC excitation to a 350 ohm load cell and delivers a 20 mA analog output.
-
Product
COM Express Type 10 Mini Application Board With LVDS, VGA, Dual LAN And Audio
CEB94018
-
*84 x 55 mini size form factor*2 GbE LAN*SATA and mSATA*LVDS and VGA*6 USB 2.0*2 PCI Express Mini Card slots
-
Product
Microwave Power Amplifiers
-
Spanawave/Giga-tronics Microwave Power Amplifiers deliver outstanding performance and exceptional value. These ultra-broadband amplifiers have excellent pulse performance and modulated signal fidelity, ideal for testing in wireless communications, defense EW and radar testing and general purpose microwave laboratory applications. Have the power you need to overcome cable and switching losses, or to drive higher power mixers, detectors and very high power amplifiers.
-
Product
Qseven V2.0 SoM Evaluation Kit With Quad/DualLite 800 MHz (Industrial) SoC, 1GB Memory, 4GB EMMC, Gigabit Ethernet, Audio And CAN
Q7M120-120-EVK
-
*Ultra low power consumption Cortex™-A9*High flexibility Qseven v2.0 compliant design*2 CAN 2.0B*18/24-bit TTL LCD*LVDS/HDMI 1080P*10/100/1000 Mbps Ethernet*Linux3.0.35/Android4.3*Audio
-
Product
Distribution Amplifiers
-
The Quartzlock range of distribution amplifiers are intended for use when multiple outputs from a single frequency standard/generator are required. This may be encountered in engineering labs, national standards labs, research and development, calibration labs and production. This is vital for the distribution of signals from other precision frequency standards like Hydrogen Masers, Cesium oscillators. For a technical discussion about distribution amplifiers go here or select a product range below.
-
Product
Tower Mounted Amplifiers
-
*Available twin and single TMA configurations*Low band, high band & dual band units, including AWS & WCS*High linearity, dual duplexed, light weight design*AISG 2.0 compliant
-
Product
Power Amplifiers
-
Triad’s line of RF and microwave Power Amplifier modules for extended range amplified radio applications set the bar for efficiency, linearity, and size-to-power ratio. We have designed hundreds of COTS modules for exacting frequencies up to 40 GHz . They offer high power levels into the hundreds of watts. And if a standard RF/microwave amplifier design does not fit your exact requirements, we’re specialists in creating custom-modified versions of any of our COTS power amplifier modules.
-
Product
Digital Quad-channel High-Frequency Lock-In Amplifier -
eLockIn 205
-
Being the top model eLockIn series, the eLockIn205/2 offers a very fast TCP/IP connection, ultra-fast DAC outputs of the measured signals and all signals supplied at BNC connectors.
-
Product
Load Cell Amplifier Signal Conditioner with Removeable Terminals
MODEL LCA-RTC
-
The LCA-RTC Module provide low-cost, dedicated signal conditioning for a single bridge type load cell or torque sensor. Model LCA-RTC comes with removable screw-clamp terminal connectors, which accept wires without soldering.On- board jumper selections include sensitivities from 0.5 mV/V to 10 mV/V, bandwidths from 100 Hz to 30 kHz, and amplified outputs of 0 to ±5V, 0 to ±10V, 0-16 mA, 0-20 mA or 4-20 mA. Zero and span adjustments are via precision 25-turn low-tempco metal film potentiometers.The units can be operated next to the sensor with 4-wire hookup or at distances up to 1 km (3300 feet) with 6-wire hookup. An onboard 87.325 kΩ resistor allows easy shunt calibration at the push of a button. Provision is also made for a user-furnished calibration resistor. Power requirements are 11.8 to 26V DC with load currents from 10 to 60 mA, the latter applying when the unit provides 10V DC excitation to a 350 ohm load cell and delivers a 20 mA analog output.
-
Product
Digital Quad-channel High-frequency Lock-In Amplifier -
eLockIn 204
-
Digital quad-channel high-frequency Lock-In Amplifier.
-
Product
Ytterbium-doped Fiber Amplifier
YDFA
-
Ytterbium-doped Fiber Amplifier (YDFA) is another Amonics specialised product line. Like our highly recognized optical amplifiers, the YDFA offers high output power and high gain with exceptional reliability. ideal for high power YDFA applications. The turnkey microprocessor controlled benchtop YDFAs manage alarms and status indicators. An integrated RS232 or Ethernet computer interface enables easy control, diagnostic functions and data acquisition. Available options include single frequency operation, linearly polarized operation.
