CompactPCI Backplanes
-
Product
DIN Backplane
-
VECTOR Electronics and Technology, Inc.
Universal (uncommitted) multilayer backplanes are designed for unique one of a kind applications requiring custom pin-out wiring from connector to connector. Each individual connector pin must be "assigned" by connecting to adjacent power or ground pins with wire or jumpers. Power or Ground input through a labeled series of power taps (screw terminals) along to top and bottom of the board.
-
Product
CompactPCI 3U Module
CPCI-1553-DDC
Controller
Operating temperatureCommercial: 0 to +55 °COptional: -25°C to +80°C• Non-operating: -40°C to 85 °C• Airflow requirement: .5 CFM• Humidity: 5 to 90% (non-cond.)• Altitude: 0 to 10’000 ft
-
Product
5-slot ATX-supported PICMG 1.3 Bus Passive Backplane
FAB110
-
The FAB110 offers one PCIe x16 slot, one PCIe x4 slots and two 32bit/33MHz PCI slots as well as the PICMG 1.3 slot for the SHB (system host board). The onboard 24-pi ATX power connector and 8-pin connector for thermal detected board are featured. Furthermore, the backplane supports two high speed USB 2.0 ports. The FAB110 is designed for the 6-slot industrial chassis, such as Axiomtek's AX60501 and AX6052.
-
Product
cPCI Serial Backplanes
-
CompactPCI Serial is an industrial standard for modular computer systems. It is based on the established PICMG 2.0 CompactPCI standard, which uses the parallel PCI bus for communication among a system's card components. In contrast to this, CompactPCI Serial uses only serial point-to-point connections.
-
Product
CompactPCI 3U 6 slot 64 bit right justified RoHS, P1s P2l
102CPCI306-20X0R
-
CompactPCI 3U 6 slot 64 bit low profile with system slot right, fully compliant to the PICMG basic specification 2.0 R3.0 and Hot Swap specification 2.1 R1.0.
-
Product
CompactPCI Chassis for 6U
-
Advantech 6U CompactPCI chassis are 4U enclosures hosting up to 8 slots, hot-swappable CPCI redundant power supplies, and hot-swappable fan modules.
-
Product
CompactPCI® Serial MXM 3.0 Type B Graphics Module Carrier
SV2-MOVIE
-
3U Carrier for MXM 3.0 Type B graphics module, 4 x DisplayPort front panel connectors, installed PNY P5000 MXM, 192bit/GDDR5 16GB, 100W TDP 2048 CUDA Cores, 8HP heat sink.
-
Product
cPCI-6540 Series 6U CompactPCI Processor Blade, Extended Temperature
20040257
-
The cPCI-6540 Series is a 6U CompactPCI® processor blade with soldered DDR4-2666 ECC memory up to 32GB and DDR4-2666 ECC socket type memory up to 32GB. The cPCI-6540 features an Intel® Xeon® E, 9th Gen Intel® Core™ and Intel® Celeron® G processor (formerly Coffee Lake-H) with Mobile Intel® CM246 Chipset. The ADLINK cPCI-6540 Series is a 6U CompactPCI blade in single-slot (4HP) width form factor. Front panel I/O includes 1x DP, 2x GbE, 2x USB 3.1 ports, 1x RJ-45 COM port, 1x VGA and 1x PCM/XMC slot. The cPCI-6540V front panel includes 1x DP, 2x GbE, 1x USB 3.1 port and 2x PMC/XMC slots.
-
Product
CompactPCI CTEL 6U 8 slot with H110 bus, P1-2s
105CTEL608-0136
-
CompactPCI CTEL 6U 8 slot with system slot left, H110 bus, fully compliant to the PICMG basic specification 2.0 R3.0, Hot Swap specification 2.1 R1, andv PICMG H.110 Computer Telephony specification 2.5 R1.0.
-
Product
6U CompactPCI Rear Transition Module with Ruggedized M12 Connectors
cPCI-RMPSA
Rear Transition Module
- Dual display with DVI-I and DVI-D- Ruggedized USB 2.0, GbE M12 ports- Dual serial ports and optional USB 3.0- Compatible CPU boards: cPCI-6530/cPCI-6520/cPCI-6940
-
Product
CompactPCI 6U 64 bit ATX 6 slot, P1s, P2-5l, RoHS
102CPCI606-4057R
-
CompactPCI 6U 6 slot 64 bit low Easycable, system slot left, with ATX connector. It is fully compliant to the PICMG basic specification 2.0 R3.0 and Hot Swap specification 2.1 R1.0.
-
Product
CompactPCI 6U 16 Slot Left Justified P1-2s, P3-5l, 2 X P47
103CPCL616-7157
-
CompactPCI 6U 16 slot 64 bit Easyplug with 2 x P47 power connector, system slot left, fully compliant to the PICMG basic specification 2.0 R3.0 and Hot Swap specification 2.1 R1.0.
-
Product
Wiring Analyzers for Cables, Wire Harnesses, Backplanes
CableEye M2Z, M3Z, M4
-
With our cable testers and harness testers, find defective or miswired cables instantly before they damage equipment or waste valuable technician time. CableEye® all-in-one test and cable management systems have a unique, patented graphic wiring display to visually pinpoint problems when wiring errors are detected, and offer under a second pass/fail testing for production environments. Quickly locate intermittent connections and identify their position in the cable.
-
Product
PCI Express Expansion Backplane
SKU-076-0X
-
PCI Express Expansion backplane was designed as a universal solution for Desktop or Laptop host computer expansion. It allows adding up to four additional PCI Express boards to the host computer. Expansion backplane can be placed inside any general-purpose computer chassis, and connects to the host computer via 5ft (or 10ft) CAT6 cable.
-
Product
8 Channel ADC for CompactPCI
CPCI393
-
The CPCI393 8-Channel Differential Input ADC card is very well suited to be used in applications in which autonomous signal conversion is an issue, as well as in standard mid-range applications. Enabled channels are scanned at maximum rate and conversion results are stored in shared memory. A local DSP performs the data acquisition and calibration transparent for the host.
-
Product
CompactPCI 6U 64 bit ATX 5 slot, P1s no P2-5, RoHS
102CPCI605-41XXR
-
CompactPCI 6U 5 slot 64 bit low Easycable, system slot left, with ATX connector. It is fully compliant to the PICMG basic specification 2.0 R3.0 and Hot Swap specification 2.1 R1.0.
-
Product
400 W 6U CompactPCI Hot-Swappable Redundant Power Supply
cPS-H640/48
Redundant Power Supply
- PICMG® 2.11 CompactPCI® Power Interface compliant- 6U CompactPCI® 8HP form factor- PICMG® 2.11 47-pin CompactPCI® in-rack power module interface- 400 W DC output, maximum 480 W peak output
-
Product
3U CompactPCI Serial FPGA 10-20 ports Industrial Ethernet
SY7-CYCLONE
-
The EKF SY7-CYCLONE is a CPCI Serial FPGA board with front panel connectors for up to 20x100Mbps SPE ports. It can be configured as Ethernet NIC, switch, router, or gateway.
-
Product
6-slot ATX-supported PICMG Bus Passive Backplane (vertical)
ATX6022/6VP4
-
*1 PICMG, 4 PCI and 2 ISA*Compatible with AX61222TP/AX61220TP*Supports ATX power supply*For 2U chassis
-
Product
6U CompactPCI 6th/7th Gen Intel® Xeon® E3 and Core™ i3/i7 Processor Blade
cPCI-6636(KL) Series
Processor Blade
The ADLINK cPCI-6636 Series is a 6U CompactPCI® processor blade based on the 6th/7th Generation Intel® Xeon® E3 and Intel® Core™ i3/i7 Processors with Intel® HM170 or CM236 Chipsets. The cPCI-6636 supports up to 16GB onboard DDR4-2133 memory and 16GB DDR4-2133 via SODIMM. Total memory capacity is up to 32GB of DDR4-2133. The cPCI-6636 is a highly integrated processor blade fit for mission critical applications in industries ranging from automation to defence.
-
Product
SC9-TOCCATA, CompactPCI® Serial CPU Card Equipped With 11th Generation Intel® Core™ & XEON® W Processors (Tiger Lake H45 Platform)
EKF-SC9-TOCCATA
-
SC9-TOCCATA is a rich featured high performance 4HP/3U CompactPCI® Serial CPU board, equipped with an Intel® 11th Generation XEON® Processor (Tiger Lake H45 platform) for demanding industrial applications.
-
Product
3U CompactPCI® 4 RJ45 Port Gigabit Ethernet Card
MIC-3958
-
Advantech MIC-3958 Series, a 3U height 4HP CompactPCI® peripheral card, using Intel® i210 Ethernet controller, to support up to four RJ45 Gigabit lan connectors, two switchable with rear transition module; MIC-3958A provides four RJ45 lan ports on front panel, MIC-3958R provides two RJ45 lan ports on rear IO panel. Its ideal power solution make it perfect for all fanless system applications.
-
Product
Dual PMC Carrier for 6U CompactPCI
TCP262
-
The TCP262 supports standard PMC front I/O and CompactPCI rear I/O fully compatible to the TCP260. The PMC slot 2 (upper PMC) I/O lines are connected directly to the CompactPCI connector J5. The PMC slot 1 (lower PMC) I/O lines are connected directly to the CompactPCI connector J3.
-
Product
1-Slot Power & Ground only 7U VPX backplane with aperture for VITA 67 in J3
1900002558-9001R
-
Power for 3.3V, 5V and 12V, rear connectors fully loaded. Use with Elma’s slot-to-slot or slot-to-I/O bulkhead cable products for system development.
-
Product
3U 4-Slot OpenVPX Backplane Aligned To SOSA With 2 VITA 67.3 Aperture Slots
1SVX304AxP-xxxx
-
Designed in alignment with the SOSA, Elma's 3U 4-Slot backplanes offer 4 Plug in Card (PIC) slots to support MOSA, CMOSS and HOST initiatives. It support high-speed signals on all data paths and VITA 67.3 connectors and VITA 66.5 optical connectors.
-
Product
4U 5-Slot CompactPCI® Chassis with Redundant Power Supplies
cPCIS-6400U Series
Chassis
The cPCIS-6400U/6400X Series subsystems are designed for 6U cPCI boards with 80mm RTMs. The chassis is 4U in height and standard 19" rack mount width.
-
Product
Other Backplane Architectures
-
Elma is well known for our backplanes based on common VITA and PICMG standards-based architectures such as VME, OpenVPX, and CompactPCI Serial. We also make backplanes for other architectures.
-
Product
PP B7x/msd, 6U CompactPCI Processor Board
PP B7x/msd
-
PP B7x/msd is a single slot air-cooled CompactPCI® board, allowing customers to easily migrate to the latest generation of Intel® processors for improved performance and longer system lifecycles.
-
Product
2-slot CompactPCI® Rackmount Chassis
cPCIS-6130R
Chassis
The cPCIS-6130R Series subsystem is designed for Telecom Data Center and Enterprise applications requiring a low profile PICMG 2.0 R3.0 CompactPCI compliant chassis with PICMIG 2.1 R2.0 hot swap support. The chassis is 1U height and standard 19" rack mount width for 6U cPCI cards, has a 2-slot board space, a hot swap backplane, a 64-bit/66MHz cPCI bus, and provides rear I/O for 80mm RTMs.
-
Product
Power Backplanes
3U cPCI
-
CompactPCI bus is compatible, in terms of electrical specification, with the PC world’s PCI bus. The mechanical specifications were adapted to the commonly used Euro-board plug in systems for 19″ racks.
