CompactPCI Backplanes
-
Product
3U OpenVPX VITA 66-67 Backplanes
-
VPX is a broadly defined technology utilizing the latest in a variety of switch fabric technologies in 3U and 6U format blades. Open VPX is the architecture framework that defines system level VPX interoperability for multi-vendor, multi-module, integrated system environments.
-
Product
Shelf Manager Carrier/Mezzanine Board for CompactPCI
064-758
-
Set of Shelf manager mezzanine board installed on the pluggable carrier board. The pluggable carrier board provides all interfaces on the rear connectors.
-
Product
12-/16-bit 16 Channel DAC for CompactPCI
CPCI395
-
The CPCI395 features 16 analog voltage outputs, integrated on the CompactPCI standard. Each output has a 12- or 16-bit resolution and a software programmable output range (0..+10V or -10..+10V). Control of the analog output is as easy as writing the binary equivalent to a dedicated register (per channel). Conversion takes place automatically. If desired, channels can be synchronized by presetting the channels and then give a simultaneous update command.
-
Product
6U CompactPCI 10 Gigabit Ethernet Switch Blade
cPCI-6S10
Switch Blade
- ARM Cortex-A9 processor integrated in Broadcom BCM56150 switch- 24-port fully managed Gigabit Ethernet switch- Pre-installed ADLINK PacketManager accelerates packet processing- Layer 2/3 switching with advanced support for VLANs, QoS and IPv6- Two 10 Gigabit Ethernet SFP+ uplink ports- Supports IPMI based on PICMG 2.9 (System Management Specification)
-
Product
CPSI-S.0 Standard Compliant Peripheral Board Controlled by a PCIe Channel Derived from a Backplane Connector P1
MIC-3811
-
It is a dual mini-PCIe carrier board with two onboard SIM card holders and mini-PCIe connectors, routed by PCIe and USB2.0 interface. It allows connection with different types of Mini PCIe form factor add on cards like Wi-Fi/3G/4G LTE/GPS/DIO/CAN/ and MVB modules, either full- or half-size style.
-
Product
CompactPCI® Serial MXM 3.0 Type B Graphics Module Carrier
SV2-MOVIE
-
3U Carrier for MXM 3.0 Type B graphics module, 4 x DisplayPort front panel connectors, installed PNY P5000 MXM, 192bit/GDDR5 16GB, 100W TDP 2048 CUDA Cores, 8HP heat sink.
-
Product
CompactPCI 3U 4 slot 64 bit right justified RoHS, P1s
102CPCI304-22XX
-
CompactPCI 3U 4 slot 64 bit low profile with system slot right, fully compliant to the PICMG basic specification 2.0 R3.0 and Hot Swap specification 2.1 R1.0.
-
Product
4U 5-Slot CompactPCI® Chassis with Redundant Power Supplies
cPCIS-6400U Series
Chassis
The cPCIS-6400U/6400X Series subsystems are designed for 6U cPCI boards with 80mm RTMs. The chassis is 4U in height and standard 19" rack mount width.
-
Product
3U CompactPCI Intel® 6th Gen. Quad- Core™ Processor Blade
MIC-3332
Processor Blade
MIC-3332 is using Intel® 14nm technology to provide significant performance and power efficiency. It provides an ideal solution for railway rolling stock, high-performance computing and military application. With its optimized design on EMC & thermal, it is available to meet or exceed EN50155.
-
Product
CompactPCI 6U 64 bit ATX 5 slot, P1-2s, P3-5l, RoHS
102CPCI605-4157R
-
CompactPCI 6U 5 slot 64 bit low Easycable, system slot left, with ATX connector. It is fully compliant to the PICMG basic specification 2.0 R3.0 and Hot Swap specification 2.1 R1.0.
-
Product
3U – 6U SOSA™ Aligned VPX Backplanes
-
Using a modular concept based on open standards it is common practice in the civil sector to integrate subsystems components from different manufacturers into a single modular system. The SOSA™ Technical Standard aims at such an interoperability in embedded computing for military applications.
-
Product
Digital Backplanes
MSXB 035
-
Digital Backplanes allow easy digital input and output expansion for large systems. Backplanes typically are used with Industrial Enclosures, which provide electrical shielding and a provide a compact unit for multiple external boards.
-
Product
6 Slot 4U CompactPCI 19" Rackmount Development Platform
39C06AD648Y4HCCX
-
The Type 39C is an advanced generation of CompactPCI chassis for PICMG 2.0, 2.16, 2.17, and EXP.0 applications. IEEE 1101.10/11, 6U x 160mm CPCI cards from the front and 6U x 80mm I/O cards from the rear.
-
Product
Power Backplanes
-
It has started with type “M” and P47 for CompactPCI, which is also used for VME64x and has progressed to newer standards like CompactPCI Serial and VPX, which receive their own unique power connector.
-
Product
14-Slot PICMG 2.16 6U CompactPCI Blade Server Backplane
cBP-6614A
Backplane
- PICMG:2.0 R3.0, 2.1 R2.0, 2.9 R1.0, 2.11 R1.0, 2.16 R1.0- Dimension:Dimension 420.6 x 262.05 (mm, WxH)- 2.16 Node Slot:12- 2.16 Fabric Slot:2- cPCI Bus:None
-
Product
CompactPCI Serial Chassis
-
CompactPCI Serial is an industrial standard for modular computer systems. It is based on the established PICMG 2.0 CompactPCI standard, which uses the parallel PCI bus for communication among a system’s card components. In contrast to this, CompactPCI Serial uses only serial point-to-point connections. CompactPCI Serial was officially adopted by the PCI Industrial Computer Manufacturers Group PICMG as PICMG CPCI-S.0 CompactPCI Serial in March 2011.
-
Product
cPCI-6636(KL) Series 6U CompactPCI Processor Blade
20040260
-
The cPCI-6636 Series is a 6U CompactPCI® processor blade based on the 6th/7th Generation Intel® Xeon® E3 and Intel® Core™ i3/i7 Processors with Intel® HM170 or CM236 Chipsets. The cPCI-6636 supports up to 16GB onboard DDR4-2133 memory and 16GB DDR4-2133 via SODIMM. Total memory capacity is up to 32GB of DDR4-2133. The cPCI-6636 is a highly integrated processor blade fit for mission critical applications in industries ranging from automation to defence.
-
Product
CompactPCI
cPCI4IP
-
The cPCI [CompactPCI] compatible cPCI4IP design adds 4 Industrypack compatible slots to your cPCI host. The cPCI4IP acts as an adapter, converter, carrier, or bridge between the cPCI bus and your IndustryPack hardware. The cPCI4IP is a 6U 4HP cPCI design with 4 IP slots.
-
Product
1 PICMG® CPU, 1 PCI-E® x16, 3 PCI-E® x4, 7 PCI™ Slots Backplane
EBP-13E4
Backplane
- Segment: 1- Slots:1 PICMG® CPU, 1 PCI-E® x16, 3 PCI-E® x4, 7 PCI™- Support ATX power supplies- Dimension: 330 mm x 318 mm
-
Product
CompactPCI 6U 64 bit ATX 3 slot, P1s, P2-5l, RoHS
102CPCI603-4057R
-
CompactPCI 6U 3 slot 64 bit low Easycable, system slot left, with ATX connector. It is fully compliant to the PICMG basic specification 2.0 R3.0 and Hot Swap specification 2.1 R1.0.
-
Product
IEEE488 (GPIB, HPIB) compactPCI Interface Card
GPIB-cPCI-XL
-
The GPIB-cPCI-XL is a GPIB controller card for PXI and CompactPCI computers.
-
Product
PICMG® 2.11 47-pin Hot-Swap Redundant 3U CompactPCI® 8HP 250 W Power Module
cPS-H325/110
Power Module
- PICMG® 2.11 CompactPCI® Power Interface compliant- Internal OR-ing Diodes for N + 1 redundancy- PICMG® 2.11 47-pin CompactPCI® in-rack power module interface- 250 W DC output- Active PFC (Power Factor Correction) meets IEC1000-3-2 Harmonic Correction
-
Product
3U 5-slots 25Gb Backplane Aligned To SOSA. AFT And VITA 48.8 Ready
1SVX306APP-1X31
-
Designed in alignment SOSA, this 3U backplane offers 5 PIC (Plug in Card) slots supporting high-speed signals on all data paths and VITA 67.3 connectors and VITA 66.5 optical connectors.
-
Product
ARINC-429 Controller for CompactPCI
CPCI302
-
The CPCI302 provides four ARINC-429 compatible channels (2x receive and 2x transmit) at any rate between 12.5 and 100kbps. Because the CPCI302 is built upon a flexible platform, the user functions can be implemented almost without restriction, making this product flexible and user-friendly.
-
Product
PCI Express, PCI, Multi-Interface Test Backplanes
-
Amfeltec PCI Express, PCI, Multi-Interface Test Backplanes
-
Product
3-slot ATX-supported 1U Butterfly PICMG 1.3 Bus Passive Backplane
FAB209
-
*Designed for PICMG 1.3 SBC*Compatible with AX61120TP chassis*Supports one PICMG 1.3 CPU card slot, one PCIe x4 slot and one PCIe x16 slot
-
Product
6U CompactPCI Rear Transition Module With Intel® Ethernet Controller I350-AM2 - CPCI-6100 Series
20040265
-
The CPCI-R6100 Series Rear Transition Module is compatible with ADLINK 6U CompactPCI processor blades and include Intel® Ethernet Controller I350-AM2.
-
Product
14-slot PICMG 1.3 Bus Passive Backplane
FAB101
-
The FAB101 features one CPU card slot and thirteen 32bit/33MHz PCI slots, and built in a 24-pin ATX power connector and 8-pin connector for thermal detected board. Furthermore, the FAB101 delivers outstanding system performance through high-bandwidth interfaces such as Serial ATA and USB 2.0 high speed peripheral (optional function). It is designed for all of PICMG 1.3 single board computers, and is a perfect fit for AXIOMTEK's SHB100 & SHB110, which are built around the PICMG 1.3 form factor. We also have various 4U-high enclosures, AX6156E, AX6156LE, AX6156LLE, AX6156LLES, AX61400, AX61491, and AX6145, to house the FAB101 and any customer's industrial integrations flexibly.
-
Product
3U CompactPCI 6-Slot Cubic Chassis with CompactPCI Power Module
cPCIS-2500 Series
Chassis
The cPCIS-2500 series 3U CompactPCI 6-slot Cubic Chassis is designed for 3U CompactPCI cards and modules without rear I/O. It is 4U in height, 237 mm deep, and suitable for bench top use or wall mounting. It is ideal for industrial or transport applications where small chassis size and versatility are important. A built in cooling system with removable filter provides maximum cooling efficiency, and the 250W cPCI power supply allows easy maintenance. The cPCIS-2500 series' ability to handle a wide range of temperatures and excellent shock and vibration characteristics make it suitable for operating in a rigorous environment.
-
Product
Type 15, CompactPCI Serial, 5 Slots, SSR, 4U, 36HP, 249mm
051-747
-
CompactPCI Serial System Type 15 with 5 Slots: 4x CompactPCI-S.0. Peripheral Slots and 1x CompactPCI-S.0. System Slot on the right side of the system platform. 1x 300W fix-mounted, air-cooled mit fan tray.
