CompactPCI Backplanes
-
Product
13-slot ATX-supported PICMG1.3 Bus Passive Backplane
FAB114
-
The FAB114 has a PICMG 1.3 CPU card slot, one PCI Express x16 slot, three PCI Express x1 slots and a total of eight 32bit/33MHz PCI slots. The onboard 24-pin ATX power connector and 8-pin connector for thermal detected board are featured. Through one PCIe x16 link, this PICMG 1.3 backplane maximize the performance of high-end PCI Express graphics and video cards. Furthermore, the backplane supports two high speed USB 2.0 ports. The FAB114 is perfect fit for AXIOMTEK's SHB100 and SHB110. AXIOMTEK also offers versatile 4U industrial chassis specially design for the FAB114, such as the AX61400, AX6156 series and AX61491.
-
Product
13-slot ATX-supported PICMG 1.3 Bus Passive Backplane
FAB119
-
*Designed for PICMG 1.3 SBC*Compatible with AX6145, AX61400, and AX6156LE chassis*Supports one PICMG 1.3 CPU card slot, one PCIe x4 slots, one PCIe x16 slot, and ten 32bit/33MHz PCI slots
-
Product
Backplane Test System
402HV
-
Our model 402HV is the result of 25 years of high voltage / high pin count test systems experience. We produced our first high voltage system back in 1985. It was programmable up to 600 volts / 600 Mohms and had over 49,000 test points. It could test a 5k point board in less that 15 seconds. Since then we have built hundreds of high voltage test systems, with our highest voltage system capable of testing up to 2000 Volts DC / 1500 Volts AC. (One of our 600 volt systems, built in 1986 is still in operation testing boards for a defense contractor.)
-
Product
3U cPCI Serial Power Backplanes
-
CompactPCI Serial is an industrial standard for modular computer systems. It is based on the established PICMG 2.0 CompactPCI standard, which uses the parallel PCI bus for communication among a system’s card components. In contrast to this, CompactPCI Serial uses only serial point-to-point connections.
-
Product
1U-4U SlimBox For CompactPCI
-
1U to 4U rack-mounted enclosure with 482.6 mm (19") mounting brackets (may be offset approximately 100 mm to the rear). Two backplane slots can fit in each 1U of chassis height (standard 0.8” pitch) with rear plug I/O options. Enclosure cooling from left to right with EMC and ESDcompatible configuration. Optional: Hot swap-compatible power supply units with current splitting for redundancy operation (2U). Conforms to IEEE 1101.1/10/11,
-
Product
4U Compact 42HP CompactPCI Serial Chassis Platform
CPCIS4VC800
-
The CPCIS4VC800 is a 4U vertical-mount chassis that holdsup to eight 3U slots at a 0.8” pitch. The modular card guidescan be adjusted to allow 1.0” pitch or other spacing in .2”increments. The standard PSU is a fixed 350W ATX, but other options are available. Conduction-cooled card guides arealso available for testing and development.
-
Product
Rugged High speed, VITA Backplane Connector System
KVPX Series
-
Smiths Interconnect's KVPX series is the most rugged VITA compliant backplane connector on the market.
-
Product
CompactPCI 3U 6 slot 64 bit right justified RoHS, P1s P2l
102CPCI306-20X0R
-
CompactPCI 3U 6 slot 64 bit low profile with system slot right, fully compliant to the PICMG basic specification 2.0 R3.0 and Hot Swap specification 2.1 R1.0.
-
Product
4U 8-Slot CompactPCI® System with Redundant Power Supplies
cPCIS-6418U
System
The cPCIS-6418U Series Subsystem is designed for maximum density and has 8 horizontal slots for 6U cPCI boards with 80mm RTMs. The chassis is 4U in height and standard 19" rack mount width.
-
Product
VME Type 32 with 6U, 5 slot Backplane
32V05MMX36N3V10
-
VME Type 32 with 6U, 5 slot Backplane J1, J2.
-
Product
PCI Express Gen 1 Test Backplane
SKU-015-01
-
The PCI Express Test Backplane was designed to support production testing/debugging of PCIe-based peripheral boards. The backplane expands the x1 PCI Express interface of the host computer into one x4 and three x1 PCI Express slots via 7 ft CAT6 cable.
-
Product
3U CompactPCI Serial Vector FlexRay CAN LIN Module Carrier
SFV-RAY
-
The SFV-RAY is a 3U CompactPCI Serial carrier card for the Vector VN7610 and similar Vector FlexRay/CAN-FD compact interfaces. On-board USB controller. Can be installed in any peripheral slot of a CPCI Serial backplane.
-
Product
3U CompactPCI Mini PCI, Mini PCIe Carrier Board
cPCI-3W10
Carrier Board
- Supports 32bit, 33/66MHz CompactPCI® bus- One SIM card socket- One Mini PCI and one Mini PCIe socket- PICMG® 2.0 R3.0 compliant
-
Product
3U OpenVPX 2-Slot Backplane With 1 VPX Power And Ground Plus 1 VITA 62 Power Supply Slot
101VPX302-xxxx
-
This 3U Open VPX backplane offers one VITA 46 Power and Ground slot and one VITA 62 power supply slot to support the development and deployment of systems requiring a VITA 62 power supply. The rear power studs can be used to connect to an adjacent backplane to feed it power.
-
Product
PMC Carrier for 3U CompactPCI
TCP270
-
The TCP270 is a standard 3U CompactPCI carrier that provides front I/O and rear I/O for a single width PMC module. This PMC to 3U CompactPCI adapter is used to build modular, flexible and cost effective I/O solutions with PMC devices in CompactPCI systems.
-
Product
CompactPCI CPSB 2.16 6U 8 slot, 6 w/cPCI, 2 Fabric, no P2
107PS21608-0257R
-
CompactPCI CPSB 2.16 6U 8 slot, 6 w/cPCI, 2 Fabric, no P2, fully compliant to the PICMG 2.16 Packet Switching Backplane specification.
-
Product
3U CompactPCI Serial FPGA 10-20 ports Industrial Ethernet
SY7-CYCLONE
-
The EKF SY7-CYCLONE is a CPCI Serial FPGA board with front panel connectors for up to 20x100Mbps SPE ports. It can be configured as Ethernet NIC, switch, router, or gateway.
-
Product
4U CompactPCI® Enclosure with cPCI Power Supply (non-CT Bus)
MIC-3042
Enclosure
The MIC-3042 is a 4U enclosure designed for standard cPCI power supplies. It is equipped with a cPCI 500 W redundant 2 1 power supply with hot-swap support. The system has 8 slots for CompactPCI boards and 6 slots for IEEE 1101.11 rear I/O transition boards. The MIC-3042 comes with a built-in high quality backplane that supports 64-bit / 66 MHz PCI cards.
-
Product
6U CompactPCI Rear Transition Modules
Rear Transition Module
ADLINK offers a diverse line of Rear Transition Module (RTM) to 6U CompactPCI platform to deliver more I/O connectivity.
-
Product
CompactPCI 6U 64 bit ATX 3 slot, P1s, P2-5l
102CPCI603-4057
-
CompactPCI 6U 3 slot 64 bit low Easycable, system slot left, with ATX connector. It is fully compliant to the PICMG basic specification 2.0 R3.0 and Hot Swap specification 2.1 R1.0.
-
Product
CompactPCI 6U 64 bit ATX 5 slot, P1-2s, P3-5l, RoHS
102CPCI605-4157R
-
CompactPCI 6U 5 slot 64 bit low Easycable, system slot left, with ATX connector. It is fully compliant to the PICMG basic specification 2.0 R3.0 and Hot Swap specification 2.1 R1.0.
-
Product
VME Backplanes
-
VME enjoys a strong, stable ecosystem, particularly in many of the areas involving x86 compute blades, I/O, digital signal processing, and areas requiring custom design. It also enjoys some cost-effectiveness due to its wide adoption in over 400 defense programs as well as in industrial automation.
-
Product
Backplane Profiling & Inspection System
603d
-
A major problem in the backplane industry is detecting bent connector pin defects. The most difficult being when the pin bends underneath the shroud rather than going into the hole. Many times this defect cannot be detected electrically as the connector pin is touching the conductive annular ring of the hole, allowing electrical test to pass. Unfortunately, it is an intermittent connection and will fail later on as there is not an actual mechanical connection.
-
Product
CompactPCI Chassis 4 Slots
2U 84HP
Chassis
Hartmann CompactPCI 2U system platform provides an intelligent, practical packaging solution for high-performance processors. The full width rack mount model provides a 4 slot 5V I/O 9U monolithic (6U cPCI) backplane for horizontal mounting of boards.
-
Product
CompactPCI 6U 64 bit ATX 4 slot, P1-2s, P3-5l, RoHS
102CPCI604-4157R
-
CompactPCI 6U 4 slot 64 bit low Easycable, system slot left, with ATX connector. It is fully compliant to the PICMG basic specification 2.0 R3.0 and Hot Swap specification 2.1 R1.0.
-
Product
CompactPCI 9U 8 Slot, P1-2s, P3-5l, 3 X P47
103CPCI908-5157R
-
CompactPCI 9U 8 slot 32 bit Easyplug with 3 x P47 power connector, system slot left, fully compliant to the PICMG basic specification 2.0 R3.0 and Hot Swap specification 2.1 R1.0.
-
Product
Rugged Conduction Cooled 3U CompactPCI Processor Blade with Quad-Core Intel® Atom™ Processor
CT-3620
Processor Blade
The ADLINK CT-3620 Series is a Rugged Conduction-Cooled 3U CompactPCI processor blade in single-slot (4HP) width form factor featuring a quad-core Intel® Atom™ SoC and soldered DDR3L-1333 ECC memory up to 4GB. Graphics is integrated graphics on the CPU and storage is provided by an onboard 32GB SSD. Rear IO signals include 2x GbE, 1x USB 2.0, VGA, 2x COM, and 1x SATA 3Gb/s, providing for expansion with an optional Rear Transition Module (RTM).
-
Product
M-Module Carrier for CompactPCI (3U)
i3000
-
The i3000 M-module Carrier for CompactPCI features a 3U form factor CompactPCI gateway to the M-module interface. One M-module mounting socket is provided by this carrier. This carrier can be used in temperatures from -40°/+85°C. The M-module interface of the i3000 complies to the M-module Specification ANSI/VITA 12-1996. The interface features A8, A24, D16 and D32 access types.
-
Product
CompactPCI 6U 64 bit ATX 4 slot, P1s P2l, RoHS
102CPCI604-40X0R
-
CompactPCI 6U 4 slot 64 bit low Easycable, system slot left, with ATX connector. It is fully compliant to the PICMG basic specification 2.0 R3.0 and Hot Swap specification 2.1 R1.0.
-
Product
VPX / Open VPX Backplanes
-
VPX is a broadly defined technology utilizing the latest in a variety of switch fabric technologies in 3U and 6U format blades. Open VPX is the architecture framework that defines system level VPX interoperability for multi-vendor, multi-module, integrated system environments.
