-
product
Light Sources
Fiber optic light sources are a low-cost way to analyze and identify accurate fiber optic readings, while certifying optical fiber. Receive the ability to measure fiber optic light continuity, loss, and quality of the signal.
-
product
PC Control Tunable Laser Source Modules
UC9710xx
The UC8710C, UC9710L and UC8710CL tunable laser modules offer superior performance in testing DWDM components, AWG & PLC components, and optical amplifiers, and performing other general- purpose fiber optical test and measurement applications particularly in fiber grating sensor fast sweep testing.
-
product
LXI High Voltage Switching - 4-Bank, 1-Pole, 4:1 Multiplexer Plugin Module
65-231-913-HI
The 65-231-913-HI plug-in module is part of a scalable high voltage multiplexer platform that provides a high voltage switching solution with capability up to 9 kV.
-
product
AC Power Source
SPS-100
Kongter Test & Measurement Co., Limited
SPS-100 is designed for various tests of analog and digital AC Voltage meter and Current meter, Single/three phase active and reactive power meter, Phase angle meter, Single/three phase power factor meter, frequency meter, and synchronous-meter, Single/three phase active and reactive power meter; it also outputs 2nd ~63rd harmonics.
-
product
AC Voltage Sensors
Continuously monitor single or three-phase power lines for over or under voltage conditions with DARE?s AC voltage sensors, voltage monitors, and voltage sensing relays. DARE?s complete line of AC Voltage Sensors will protect system equipment and circuitry from voltage that is hazardous or unsuitable for operation.
-
product
Resets And Voltage Detectors
ST’s reset and voltage detector ICs provide basic voltage monitoring (low-voltage detect POR-LVD function) and reset timing for power-on resets. These devices offer:
-
product
High Voltage Testers
GLP2
GLP2-tester series are the result of our experience in manufacturing following “customer based technology“ for more than 20 years. With precise, intelligent test processes the testers set the standard regarding operating ease, modularity, functionality, measurement accuracy and performance.AC tests up to 100 kV. DC tests up to 98 kV. Suitable for production testing of luminaries, white goods, coils etc.
-
product
Source of Signals
CRS+
The CRS+ is a stable and calibrated source of signals which cover the 9KHz - 30MHz frequency range. The fundamental signal is a 15KHz comb and each harmonic is output as a narrowband peak of known amplitude. This signal is output on either the L and N lines, referenced to ground. A switch provides on/off and line selection.
-
product
Flexible Monitoring of Voltage & Current in A 2 B ® Networks
Line Test Box LTB 1024
The Automotive Audio Bus (A 2 B ® ) from Analog Devices Inc. reduces the complexity of audio systems. In addition to the automotive industry, it is also increasingly being used in other areas such as conference systems. We have developed a line measuring device specifically for this A 2 B ®technology: the Line Test Box LTB 1024.
-
product
Low Voltage Container Load Banks
Guangdong EMAX Electrical Co., Ltd.
Container load banks are portable, self-contained solutions for testing and maintaining large power systems, designed to be easily transported and deployed in a variety of environments, making them ideal for both temporary and permanent installations.
-
product
Incandescent Light Sources
Collimated, uniform, 1 inch diameter output beamSupports 75W-300W QTH LampsSupports xenon, mercury, & mercury-xenon arc lampsForced Air CooledRefractive condensing optics attachments availableVariable power supply (purchased separately) with optical feedback (option)Vertically mounted arc lampSide exit port with back spherical reflector
-
-
product
PXI High Voltage Amplifiers
Pickering's PXI High Voltage Amplifiers are ideal for increasing the output voltage from other PXI modules, enabling users to easily generate the signal voltages commonly required in applications such as automotive test. Each amplifier can be independently programmed to a gain of 1, 2, 5, 10 or 20, enabling it to be used with modules with low output voltage capability. Inputs and outputs can be provided either on SMB connectors or on a D Type connector to suit the user’s wiring system.
-
product
Noise Source, 1 GHz up to 50 GHz
346CK01
The Keysight 346CK01 is the ideal companion to Keysight´s noise figure solutions when working on high frequency applications. Since it is broadband (1 GHz to 50 GHz), it eliminates the necessity for several sources at different frequency bands. The low SWR of the noise source reduces a major source of measurement uncertainty, which are reflections of the test signals. This is a coaxial noise source with a 2.4 mm coaxial connector. ENR typically 20 dB at 1 GHz, decreasing to typically 7 dB at 50 GHz.
-
product
Rad Hard Source Drivers
Renesas' radiation hardened source driver products reduce the size, weight and power of satellite subsystems such as command and telemetry control and communication satellite payloads, enabling satellite manufacturers targeting various mission profiles to significantly increase system capacity and reduce solution footprint by 50 percent.
-
product
LXI High Voltage Matrix - 400V 50x4 Matrix Plugin Module
65-218-101
The 65-218-101 plug-in module is part of a scalable high voltage matrix platform designed to provide a large matrix solution with a switching capacity of 400V. This version of plug-in includes access to the chassis backplane.
-
product
1kV, 25 MHz High Voltage Differential Probe with Auto Zero Disconnect
HVD3102A
The HVD3000A series of high voltage differential probes cover the fullest range of applications, from 120/240 V switch-mode power supplies through 600 V class and 5 kV electrical apparatus. The table below provides a list of recommended probe models based on specific device under test applications.
-
product
Noise Source, 10 MHz to 18 GHz, nominal ENR 15 dB
346B
The Keysight 346B noise source is the ideal companion to Keysight's noise figure solutions. Since it is broadband (10 MHz to 18 GHz), it eliminates the necessity for several sources at different frequency bands. The low SWR of the noise source reduces a major source of measurement uncertainty; reflections of test signals. The 346B's high ENR, low SWR, and variety of connectors make it a general-purpose noise source. Add special option H01 for high ENR (21 dB typical) to measure high noise figure devices, or option H42 for measuring Direct Broadcast Satellite (DBS) low noise block converters.
-
product
High Voltage 9 Pin D-Type Connectors for Pickering
The connectors below are suitable to use with Pickering cards and modules that utilize a high voltage 9-pin D-type connector.
-
product
Laser Source Simulator
MT1888 Series
The MT1888 products are state-of-the-art Laser Source/Spot Simulators (LSS) used for the testing of laser guided munitions such as the Hellfire & Hellfire II missiles, Paveway, and the AGM-65E Laser Maverick missile.
-
product
LXI High Voltage Matrix - 750V 50x4 Matrix Plugin Module
65-218-111
This plug-in module is part of a scalable high voltage matrix platform designed to provide a large matrix solution with a switching capacity of 750V without access to the chassis backplane.
-
product
LXI High Voltage Switching Multiplexer
65-231-914-HI
The 65-231-914-HI plug-in module is part of a scalable high voltage multiplexer platform that provides a high voltage switching solution with capability up to 9 kV.
-
product
5cc Dual Dopant Source
Attain precise and stable control of relatively low fluxes for dopant constituents in molecular beam epitaxy (MBE) through this compact dopant source. Its small thermal mass gives it excellent responsiveness, reproducibility, and stabilization for advanced doping profiles, plus consistent flux uniformity across an entire platen. Efficient cell heating minimizes thermal load.
-
product
High Voltage 50 Ω Pulse Generator for CMTI
CMTI-8010C
High Power Pulse Instruments GmbH
The CMTI-8010C is a high voltage 50 Ω pulse generator for static and dynamic common mode transfer interference (CMTI) evaluations of digital isolators according IEC-60747-5-5 and IEC-60747-17.
-
product
2 kHz C Band Fast Swept Tunable Laser Source
CA92050-KT
The CA92050-KT 2 kHz fast swept tunable laser modules offer superior performance for the test of Fiber Vibration Sensing, DWDM components, AWG , WSS, OPM components, Fiber sensing( especially for vibration fiber sensing application) , optical amplifiers, and other general purpose of fiber optical test and measurement with high wavelength resolution applications.
-
product
Low Voltage Detectors
LVD-17
Standard Electric Works Co., Ltd
● Microprocessor-controlled smart voltage detector.● Bright LED and audible alarm sound when voltage is present.● Designed for non-contact voltage detection.● Sensitivity adjustable with thumbwheel.● Adjustable for use on power wiring plus lighting, thermostats and other low voltage circuits.● LED indication for battery condition.● Identify Hot and Neutral.
-
product
Optical Light Sources
Shanghai Joinwit Optoelectronic Tech,co.,Ltd
Joinwit Optical Light Sources
-
product
Standard Voltage 37 Pin D-Type Cables - Connector to Connector
The connector to connector cable assemblies below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
product
High Voltage Switching Systems
HXV Series
HXV products are high voltage systems intened for Hi-pot / IR or High voltage switching. They can be configured to drive from 32 to 128 switch points per chassis and can be configured as multiplexer (1xN) or Matrix (NxM) configurations. Stand HXV chassis are used for signals up to 5000 VAC rms ( 7400 V peak ) and can carry up to 5 amps of current. Custom systems can be built up to 25KV. Most of the modules used in these systems are 1xN multiplexers or 2x4 matrix modules that can be combined to form larger multiplexers or matrices. Connector options for standard HXV include 5 way banaba jacks / binding posts, Shrouded Banana Jacks or SHV ( High voltage BNC) if you need to use a high voltage cable with a grounded shield for safety applications. Control options include 10/100BaseT Ethernet LAN, RS232, GPIB or optional manual control. Standard HXV systems use high voltage reed relays. Custom HXV systems up to 25KV use application specific relays and connectors from a variety of vendors based on required specifications.
-
product
Precision I/V Source
MeasureReady™ 155
The MeasureReady™ 155 Precision I/V source combines premium performance with unprecedented simplicity for materials scientists and engineers requiring a precise source of current and voltage. Low RMS noise: from 200 nV (10 mV)/7 pA (1 µA). Bipolar, 4-quadrant power source. DC and AC modes supported up to 100 kHz*. Full scale ranges from 10 mV to 100 V (1 μA to 100 mA). 0.001% programming resolution (from 100 nV/10 pA.
