D-Sub
D-Subminature Connector Also known as: DSub
-
product
4-Port Serial Interface
APCI-7500-3
This Model has a 37-pin D-Sub male connectorRS232, RS422, RS485, 20 mA Current LoopModular structure through SI modulesWith or without optical isolationMode configuration free for each port128-byte FIFO-buffer, common interruptTransfer rate programmable up to 115,200 BaudOption: up to 1 MBaud for RS485 and RS422Automatic direction recognition for RS48Mode: configurable RS232, RS422, RS485, 20 mA Current Loop (active, passive) with or without isolation (SI modules)Transmission mode asynchronous, full, half duplexTransfer rate: progr. up to 115.2 kBaud up to 1 MBaud on requestProtocol: 5, 6, 7 or 8-bit character 1, 1? or 2 stop bitsParity: even, odd, none, mark or spaceInterrupt lines: automatic through BIOS
-
product
Cable Assy, Type SH100-100-Flex, 1 m
185095-01
The SH100M-100M Flex Cable, sometimes referred to as SH100-100-F, connects NI digital I/O devices to 100-pin accessories with D-SUB connectors. The SH100M-100M Flex Cable is offered in different lengths.
-
product
Breakout Box
T1000-9
T1000-9 breakout box is our most compact breakout box, using dual 9 pin D-Sub connectors for signal capture or monitoring. Dual connectors provide a total of 18 test points plus a ground jack. All test points use standard size 4mm banana jacks. Ideal for continuity testing, isolation testing or signal capture and monitoring.
-
product
X13 GPIB Cable, MicroD25 to Shielded cable/Standard connector, 2M
183285-02
24-Pin Male/Female GPIB to 25-Pin Male Micro D-SUB GPIB Cable - The 24M-24F-MicroDB25M X13 GPIB Cable, sometimes referred to as the X13 cable, connects your system to GPIB devices or interfaces for instrument control. This standard shielded cable can connect PXI Controllers to instrument control devices and is offered in different lengths.
-
product
36" Cable
RCONCEI-620
36" cable (with twisted pairs) transitions from a card end connector (P1 or P2) on the CEI-620, CEI-820 or RAR-cPCI to a 50 pin D-sub male connector.
-
product
High Performance Cables And Accessories
Cables are designed and manufactured by Celadon. Cables are available in lengths custom to the half-meter, and can be manufactured with a variety of industry standard connectors, such as coaxial, triaxial, Type8, Edge 24/48 or 35/70, DSub 9, 15, 25, or 50; or advanced multi-contact. Depending on the overall size of the final product, an anti-abrasion sheath may be used to prevent wire wear.
-
product
15' Cable, 78-Pin Male Connector On One End, Loose Wired (Numbered) Other End
GT97112
15' harness, 78-pin male D-sub connector on one end, loose wired (numbered) other end.
-
product
Multiplexer
Marvin Test Solutions’ switch card portfolio includes matrix, multiplexer, and RF multiplexer configurations. 3U and 6U PXI switch cards feature easy to use, reliable, and integration-friendly D-sub style interface connectors – a feature unique to Marvin Test Solutions PXI switch cards. GENASYS switch cards are compatible with MTS’s family of GENASYS Switching and Switching/Digital Subsystems, featuring integrated MAC Panel SCOUT receivers.
-
product
68 POS VHDCI Conn to Eight 9 POS D-SUB, RS 485, 1M
197546-01
68 POS VHDCI Conn to Eight 9 POS D-SUB, RS 485, 1M
-
product
SH37F-Tajimi Shielded Cable, 10M
199254-10
37-Pin D-SUB Female to 4 7-Pin Tajimi Female, C Series Strain/Bridge Input Module Multifunction Cable - The SH37F-Tajimi connects with compatible sensors to accessories or cables with Tajimi push-pull connectors.
-
product
Cable Assembly, Receiver, QuadraPaddle, 36", 78-Pin Female D-Sub
540034010240
Cable Assembly, Receiver, QuadraPaddle, 36", 78-Pin Female D-Sub
-
product
Solder Cup Connector Kit
Y1139A
Used to build custom cables for 34921/23/25/31/32/33/37/38 –50-pin Dsub female – 125 V
-
product
Digital Cable
The Digital Cable models include a variety of industry-standard front- and back-end connectors, such as 68-pin VHDCI, 68-pin D-SUB, and flying lead options. Some models can connect digital instruments with other accessories to break out cable signals for direct access. Others provide flying leads that plug directly into any 0.1 in. header connector.
-
product
1' Harness, 78-Pin Male D-Sub Connector
GT97104
1' harness, 78-pin male D-sub connector on both ends
-
product
SAEJ1962M-DE9M CAN OBD-II Cable, SAE J1962 to D-sub 9-pos F, 2m
193942-02
9-Pin, Male SAE J1962 OBD-II Type A to 9-Pin, Female D-SUB - The OBDII9M-DB9F CAN Cable, sometimes referred to as the CAN OBD-II Cable, connects any NI high-speed CAN interface to an OBD-II compliant vehicle that has high-speed CAN on its diagnostic link connector in the passenger compartment. This high-quality injection-molded cable connects the CAN wires from the SAE J1962 connector to the standard CiA-DS-102 D-SUB connector wiring used by NI CAN interfaces. This cable is available with a high-speed CAN physical layer and no termination.
-
product
Digital I/O Card w/CoS IRQ
mPCIe-DIO-24S
The mPCIe-DIO-24S is a type F1 PCI Express Mini Card (mPCIe) and optional cable assembly (D-Sub 37-pin Male connector) designed to be easily panel-mounted in any application environment. It uses the high speed PCI Express bus to transfer digital data to and from the card. The digital I/O is compatible with 8255 PPI chips making it easy to program.
-
product
Cable Assembly, Receiver, TriPaddle, 36", 2 9-Pin Female D-Subs, for RS-232
540127010201
Cable Assembly, Receiver, TriPaddle, 36", 2 9-Pin Female D-Subs
-
product
3' Harness, 50-Pin Male D-Sub Connector
GT97109
3' harness, 50-pin male D-sub connector on both ends.
-
product
DB37F-DB37M LP, Low Profile I/O Cable, 37-pin Female DSUB to Male DSUB (1m)
154302-01
Low Profile I/O Cable, 37-pin Female DSUB to Male DSUB (1m)
-
product
CB-37F-HVD, 37-pin ScrewTerminal Blk, UL rec.150V CAT II, Din Rail
779491-01
37-Pin Female D-SUB to 37-Pin Female Screw Terminal, High Voltage Horizontal DIN Rail Terminal Block - The CB-37F-HVD features screw terminal connectivity for up to 37 I/O signals, 12 to 30 AWG. It has a female 37-pin D-SUB connector for connectivity to C Series I/O Modules and … data acquisition devices. The CB-37F-VHD is UL recognized. You can use the CB-37F-VHD with low-voltage or high-voltage products up to 150 V.
-
product
PXI General Purpose 2A Relay Module 16xSPDT, 78 D-sub
40-131-101
Low cost, general purpose electromechanical relay cards suitable for use where reed relay based switching cards do not have sufficient voltage or current carrying capability. Applications include switching of medium power AC and DC loads or slave switching larger relays, contactors or solenoids. Connections are made to the card via a front panel mounted 50 or 78 pin D-Type connector plug.
-
product
SHC68M-68F-RMIO, 68-Pin Male VHDCI to 68-Pin Female D-SUB, Shielded Multifunction Cable 1m
189588-01
68-Pin Male VHDCI to 68-Pin Female D-SUB, Shielded Multifunction Cable 1 m. SHC68-68-RMIO CABLE, 68-POS .50 SERIES D-TYPE TO 68-POS VHDCI OFFSET, 1M
-
product
Audio Card I/O Modules
PIM481-J/DSUB
The PIM481-J PMC I/O Module, with four 3.5mm stereo connectors and the PIM481-DSUB PMC I/O Module, with D-sub for rear I/O can be mounted on a rear transition module (RTM).
-
product
DB25F-DB25F, 25-Pin D-Sub Cable for SMUs, Low Leakage, 2 m
782015-02
DB25F-DB25F, 25-Pin D-Sub Cable for SMUs, Low Leakage, 2 m
-
product
Cable Assembly, Receiver, TriPaddle, 20", 78-Pin Female D-Sub
540034010103
Cable Assembly, Receiver, TriPaddle, 20", 78-Pin Female D-Sub
-
product
SHC68-68, 68-Pin VHDCI Male to 68-Pin D-SUB Female, Twisted Pair, Basic Shielded Multifunction Cable, 1m
191945-01
68-Pin Male VHDCI to 68-Pin Female D-SUB, Twisted Pair Cable with Basic Shielding, 1m
-
product
SP6T RF Pin Diode Switches To 12 GHz
The SP6T series of 6-way absorptive and reflective switches manufactured by Pulsar Microwave cover applications from 300 MHz to 12 GHz. They have an isolation of 60 decibels and most models specify 1.6:1 or better return loss throughout frequency band. These 6-way switches require a +/- 5VDC supply to operate. Switching control uses individual 0-5V TTL control logic. Voltage and logic control interfaces into a system using a 9-pin D-SUB connector installed.
-
product
Integrated Potentiostat and Multiplexer
EmStatMUX8
Based upon the EmStat range, there are two types of multiplexers to suit most types of sensor array work. The MUX8 is the most flexible offering the ability to connect arrays made of up to eight working electrodes in two or three electrode cell types and chips sharing a reference electrode and/or counter electrode. The MUX16 is suitable for sensor arrays or chips with sixteen working electrodes all sharing a RE and/or a CE. Both instruments are suitable for laminated layer corrosion analysis.The potentiostat is controlled and powered by USB and is used with PSTrace allowing for simultaneous sampling of each channel at a rate of 25 ms/channel. Standard packaging includes a shielded cable with connections for a working, a counter and a reference electrode by means of 2 mm banana connectors and mini-crocodile clips, a stripped end, Dsub-37 terminated flat cable and a USB cable. To make connections to chips simpler the Connection Terminal is an optional extra providing clearly marked screw terminals to the electrodes and can be directly joined to the ESMUX via their D-Sub connectors.
-
product
Cable Assembly, Receiver, TriPaddle, 36", 44 Pin ML DSub, (2) SMB Plugs, Twisted Pair
540149050201
Cable Assembly, Receiver, TriPaddle, 36", 44 Pin ML DSub, (2) SMB Plugs, Twisted Pair.
-
product
PXI Pull-Thru Adapter, Wired, QuadraPaddle, to 78 Pin Female D-Sub
510140194
PXI Pull-Thru Adapter, Wired, QuadraPaddle, to 78 Pin Female D-Sub
