D-Sub
D-Subminature Connector Also known as: DSub
-
Product
SP6T RF Pin Diode Switches To 12 GHz
-
The SP6T series of 6-way absorptive and reflective switches manufactured by Pulsar Microwave cover applications from 300 MHz to 12 GHz. They have an isolation of 60 decibels and most models specify 1.6:1 or better return loss throughout frequency band. These 6-way switches require a +/- 5VDC supply to operate. Switching control uses individual 0-5V TTL control logic. Voltage and logic control interfaces into a system using a 9-pin D-SUB connector installed.
-
Product
X13 GPIB Cable, MicroD25 to Shielded cable/Standard connector, 2M
183285-02
GPIB Cable
24-Pin Male/Female GPIB to 25-Pin Male Micro D-SUB GPIB Cable - The 24M-24F-MicroDB25M X13 GPIB Cable, sometimes referred to as the X13 cable, connects your system to GPIB devices or interfaces for instrument control. This standard shielded cable can connect PXI Controllers to instrument control devices and is offered in different lengths.
-
Product
50-Pin D-Type Female Connector Block
92-965-050-F
Connector Block
This connector block provides a simple method of connecting to 50-Pin D-Type connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. PTFE cables are recommended for use with this connector block to maximise copper cross-sectional area and insulation properties.
-
Product
3'Harness, 50-Pin Male D-sub Connector on one end, loose wired (numbered) other end
GT97107
-
3' harness, 50-pin male D-sub connector on one end, loose wired (numbered) other end.
-
Product
25-Pin D-Type Connector, Male
40-960-025-M
D-Sub Male Connector
25-Pin Male D-Type Connector - With Backshell, Solder Bucket
-
Product
15-Pin D-Type Connector, Male
40-963-015-SM
D-Sub Male Connector
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires. 15-Pin Female connectors can be directly mated to a corresponding Pickering Switching Module while Male versions can be used to interface to a Female cable assembly termination.
-
Product
Keysight 20-Channel 5A Form A Switch for 34980A
34938A
General Purpose Switch
The Keysight 34938A is a high power general-purpose switch module for the 34980A Multifunction Switch/Measure Unit. It has 20 independent single-pole, single-throw (SPST) 5A relays. This module is used to cycle power to products under test, control indicator and status lights, and to actuate external power relays and solenoids. Its 30VDC/250VAC, 5A contacts can handle up to 150W on a single channel, enough for many power line switching applications. Standard 50-pin Dsub connectors allow for use with standard cables, terminal blocks, or mass interconnect solutions.
-
Product
R6868, Low-Cost, Unshielded Ribbon Cable, 0.25 m
182482-0R25
Ribbon Cable
68-Pin Female to 68-Pin Female, 1 Ribbon Connection Ribbon Cable - The R68F-68F Cable, sometimes referred to as the R68-68 or RC68-68, is a flat ribbon cable that connects to 68-pin NI data acquisition or digital I/O devices. The R68F-68F Cable is offered in different lengths and with D-SUB or VHDCI front end connectors.
-
Product
Cable Assembly, Receiver, QuadraPaddle, 20", 78-Pin Female D-Sub
540034010140
Cable Assembly
Cable Assembly, Receiver, QuadraPaddle, 20", 78-Pin Female D-Sub
-
Product
CB-37FH, DIN-Rail Vertical Mount 37-Pin Spring TB
778685-01
Terminal Block
37-Pin Female D-SUB to 37-Pin Female Screw Terminal, Vertical DIN Rail Terminal Block - The CB-37FH is an unshielded connector block that provides access to NI data acquisition devices with 37-pin D-SUB connectors. The CB-37FH is a vertical connector block that mounts perpendicular … to the DIN rail. It features screw terminals for connecting to 37 I/O signals, 12 to 30 AWG.
-
Product
SAEJ1962M-DE9M CAN OBD-II Cable, SAE J1962 to D-sub 9-pos F, 2m
193942-02
CAN Cable
9-Pin, Male SAE J1962 OBD-II Type A to 9-Pin, Female D-SUB - The OBDII9M-DB9F CAN Cable, sometimes referred to as the CAN OBD-II Cable, connects any NI high-speed CAN interface to an OBD-II compliant vehicle that has high-speed CAN on its diagnostic link connector in the passenger compartment. This high-quality injection-molded cable connects the CAN wires from the SAE J1962 connector to the standard CiA-DS-102 D-SUB connector wiring used by NI CAN interfaces. This cable is available with a high-speed CAN physical layer and no termination.
-
Product
Cable Assembly, Receiver, TriPaddle, 20”, 6 9-PIN DSUB
540352010101
Cable Assembly
Cable Assembly, Receiver, Tripaddle, 20”, 6 9-PIN DSUB
-
Product
9-Pin D-Type Connector Block
92-965-009-F
Connector Block
This connector block provides a simple method of connecting to 9-Pin D-Type connectors. The screw terminals use a rising cage screw clamp mechanism to minimize risk of copper strand breakage.
-
Product
9-Pin Male D-Sub to 5-Pin Female Screw Terminal, Breakout for CAN Terminal Block
780041-01
Terminal Block
9-Pin Male D-Sub to 5-Pin Female Screw Terminal, Breakout for CAN Terminal Block - The CAN Breakout Box works with high-speed, low-speed, and single-wire controller area network (CAN) devices or PC interfaces. It features 14 ports for connecting devices with cables or directly to wiring harnesses. With an onboard power supply, the CAN Breakout Box can place power on the V+ pin required by some CAN transceivers. With a switch on the front panel, you can select 120 Ω, 60 Ω, or no termination on the network. You can use the CAN Breakout Box in desktop applications or mounted on a DIN Rail for test fixtures and cabinets.
-
Product
50-Pin D-Type Connector, Right Angle PCB
40-963-050-RF
D-Sub PCB-Mount Connector
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires.
-
Product
NI CAN Single Termination, High-Speed/FD Cable, 2m
192017-02
CAN Cable
9-Pin Female D-SUB to 9-Pin Female D-SUB CAN Cable - The DB9F-DB9F CAN Cable connects C Series CAN Interface Modules, C Series LIN Interface Modules, or C Series Multiprotocol Interface Modules to devices, breakout boxes, and accessories. It is sometimes referred to as CAN Cable (single termination or no termination). This cable is compatible with high-speed, flexible data-rate, and low-speed/fault tolerant CAN signals, available with or without termination, and in different lengths.
-
Product
4 Port RS-232 & 4 Port RS-422 Interface cPCI Card
GX3904
cPCI Card
The GX3904 is an 8-port, cPCI asynchronous communications interface board supporting (4) RS232 and (4) RS422 signal levels. The four RS232 ports offer a full set of data and modem control lines configured for DTE operation. The four RS422 ports offer differential signaling and support DTE operation. Each RS422 differential pair is terminated by a 150 parallel resistor. An optional transition cable is available to convert the front panel SCSI connector to (8) DB-9, D-sub connectors.
-
Product
96 Channel DPST Relay And Control PXI Carrier Card
GX6196
Relay
The GX6196 is a 6U PXI switch and control board that can be used to create custom switching, signal conditioning, or specific UUT control interfaces. The board provides 96, 2 pole, form A relays, 8 digital I/O lines, and a serial digital interface. All of these resources are available via (5) inter-board connectors which interface to the user defined daughter / mezzanine board. The mezzanine board provides all connections to the unit under test (UUT) via two 78 pin D-sub connectors. The GX6196 is supplied with a front panel which accepts (2) 78 pin D-sub connectors.
-
Product
SCB-68A, Noise Rejecting, Shielded I/O Connector Block
782536-01
Terminal Block
68-Pin Female Screw Terminal to 68-Pin Female D-SUB, DIN-Rail, Shielded I/O Connector Terminal Block - The SCB-68A provides a shielded I/O connection for interfacing I/O signals to plug-in data acquisition devices with 68-pin connectors. This Terminal Block combines with shield cables to provide low-noise signal termination. The SCB-68A incorporates a completely redesigned mechanical enclosure with a magnetic removable lid, DIN-rail mount compatibility, and a resettable fuse. It is compatible with single- and dual-connector Multifunction I/O with 68-pin connectors. The SCB-68A also includes two general-purpose breadboard areas and an onboard cold-junction compensation sensor.
-
Product
PXI Switching Instrumentation
Matrix
-
Marvin Test Solutions’ switch card portfolio includes matrix, multiplexer, and RF multiplexer configurations. 3U and 6U PXI switch cards feature easy to use, reliable, and integration-friendly D-sub style interface connectors – a feature unique to Marvin Test Solutions PXI switch cards. GENASYS switch cards are compatible with MTS’s family of GENASYS Switching and Switching/Digital Subsystems, featuring integrated MAC Panel SCOUT receivers.
-
Product
SH37F-Tajimi Shielded Cable, 10M
199254-10
Multifunction Cable
37-Pin D-SUB Female to 4 7-Pin Tajimi Female, C Series Strain/Bridge Input Module Multifunction Cable - The SH37F-Tajimi connects with compatible sensors to accessories or cables with Tajimi push-pull connectors.
-
Product
9-Pin D-Type Male, Solder Bucket, HV
92-960-009-M-HV
D-Sub Male Connector
9-Pin Male D-Type Connector, High Voltage, Solder Bucket - Without Backshell
-
Product
Keysight 32-Channel FormC/Form A General Purpose Switch for 34980A
34937A
General Purpose Switch
The Keysight 34937A is a general-purpose switch module for the 34980A Multifunction Switch/Measure Unit. It has 28 independent single-pole, double-throw (SPDT) 1A relays and 4 single-pole, single-throw (Form A) 5A relays. This module is used to cycle power to products under test, control indicator and status lights, and to actuate external power relays and solenoids. The Form C channels are 300V, 1A contacts and can handle up to 60W, and the Form A channels are 30VDC/250VAC, 5A contacts and can handle up to 150W. Standard 50-pin Dsub connectors allow for use with standard cables, terminal blocks, or mass interconnect solutions.
-
Product
Cable Assembly, Receiver, 36", TriPaddle, to 37 Pin Female D-Sub
540016020203
Cable Assembly
Cable Assembly, Receiver, 36", TriPaddle, to 37 Pin Female D-Sub
-
Product
50-Pin D-Conn Female Straight PCB
40-963-050-SF
D-Sub PCB-Mount Connector
Ideal for user created termination schemes where the termination is to be on the front or remotely connected to the module by cable. Suitable cables for this product are detailed in the data sheet. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires.
-
Product
1' Harness, 50-Pin Male D-Sub Connector on one end, loose wired (numbered) other end
GT97106
-
1' harness, 50-pin male D-sub connector on one end, loose wired (numbered) other end.
-
Product
Audio Card I/O Modules
PIM481-J/DSUB
-
The PIM481-J PMC I/O Module, with four 3.5mm stereo connectors and the PIM481-DSUB PMC I/O Module, with D-sub for rear I/O can be mounted on a rear transition module (RTM).
-
Product
9 Pin D-Type, Male, Straight PCB Mount, HV
40-963-009-SM-HV
D-Sub PCB-Mount Connector
9-Pin Male D-Type Connector, High Voltage - Straight PCB Mount
-
Product
SP16T RF Pin Diode Switches To 10 GHz
-
Pulsar Microwave's 16-way switches cover 500 MHz to 10 GHz in single pole, 16-throw configuration. Maximum input power is 200 mW and switching time is 100 ns. SMA female connectors are standard. A 15-pin D-SUB male connector makes the internal connections to the power, ground and logic circuitry. Switching control is TTL with the option of line drivers and decoders.
-
Product
Solder Cup Connector Kit
Y1140A
-
Used to build custom cables for 34922, 34924 – 78-pin Dsub female – 60 V
