Synchronization Modules
-
Product
Coax Module, ITA, 20/26 GHz, 17 Position. For use with 20/26 GHz ITA contacts with SMA adapter
510108240
ITA Module
For use with 20/26 GHz ITA contacts with SMA adapter.Primary mating module 510104287.
-
Product
PXI 10A Fault Insertion Switch 6-chan 2-bus
40-192-012
Fault Insertion Unit
This PXI fault insertion switch uses solid state switching elements and is capable of switching current up to 10A. It is designed to be able to insert three different fault conditions between the test fixture and the equipment under test: Open-Circuit. Short-Circuit between UUT connections. Short-Circuit to external signals. Through relays on each channel enable signals to the UUT to be set open-circuit. Fault Insertion Buses allow any channel to be shorted to any other channel and also enable any channel to be connected to an external signal such as Power, Ignition or Ground to simulate fault conditions. The module is supplied with 2 fault buses.
-
Product
PXI Dual 4 to 1 RF Multiplexer 2GHz 50 Ohm SMA
40-746-521
Multiplexer Module
40-740, 40-745 and 40-746 RF Multiplexers are a range of Bi-Directional Multiplexers with bandwidth up to 2000MHz. They are arranged as Single 8 to 1, Dual 4 to 1 or Single 4 to 1 configurations, all with excellent Insertion Loss, VSWR and Isolation, in 50 Ohm or 75 Ohm versions with a wide choice of connectors.
-
Product
PXI/PXIe MEMS RF Multiplexer, Quad 4-Channel, 4GHz, 50Ω, SMB
40-878-241
Multiplexer Module
The module is based on the latest micro-electromechanical system (MEMS) switching technology and has low insertion loss and VSWR. In addition, MEMS devices have a long operational life of >3 billion operations and benefit from an operating time of <20 μs allowing greater test system throughput. The multiplexers have excellent and repeatable RF characteristics beyond 4 GHz with each path having a nominally equal insertion loss.
-
Product
Quad 8 to 1 50 600MHz PXI RF Multiplexer
40-762-004
Multiplexer Module
This 4 to 1 multiplexer is part of a range of RF multiplexers available in the following configurations: dual, quad and octal 4 to 1, single, dual and quad 8 to 1, single and dual 16 to 1 and single 32 to 1. All multiplexers have the option of automatic terminations which offer advantages at system level by reducing the presence of standing waves in the system which can cause degradation in isolation and crosstalk.
-
Product
PXI/PXIe High Voltage Multiplexer, Single 48-Channel, 1-Pole
42-321-109-HI
Multiplexer Module
The 40-321-109-HI (PXI) and 42-321-109-HI (PXIe) are single 48-channel 1-pole high voltage multiplexers capable of hot or cold switching up to 1000 V peak. They are also available in a range of bank sizes with 1 or 2 poles and channel counts between 4 and 48. High quality reed relays are used throughout.
-
Product
NI-9860, 2-Port, C Series Vehicle Multiprotocol Interface Module
783703-01
Interface Module
2-Port, C Series Vehicle Multiprotocol Interface Module—The NI‑9860 is a hardware-selectable HS/FD controller area network (CAN) and/or local interconnect network (LIN) interface for developing CAN and/or LIN applications. As part of the NI‑XNET platform, the NI‑9860 works well for applications requiring high-speed manipulation of hundreds of frames and signals while taking other data acquisition measurements in the same CompactDAQ hardware platform or while performing low-level FPGA control and embedded monitoring in the same CompactRIO chassis.
-
Product
PXI/PXIe Microwave Transfer Switch, Single, 18 GHz, 50 Ω, SMA, Failsafe, Remote Mount
40-782B-521-E
Switch Module
The 40-782B-521-E (PXI) and 42-782B-521-E (PXIe) single failsafe transfer switches with remotely mounted relays are part of our range of PXI microwave switching modules. They have a characteristic impedance of 50 Ω and a maximum operating frequency of 18 GHz. Connections are made via front panel mounted high quality SMA coaxial connectors.
-
Product
PXI 2A Multiplexer, 1-Bank, 64-Channel, 2-Pole
40-614B-016
Multiplexer Module
This 1-bank, 64-channel, 2-pole version is part of the 40-614B High Density 2A multiplexer module range that is available in 20 configurations (see Also in this Range link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
LXI High Voltage Switching - 4-Bank, 1-Pole, 4:1 Multiplexer Plugin Module
65-231-913-HI
Multiplexer Module
The 65-231-913-HI plug-in module is part of a scalable high voltage multiplexer platform that provides a high voltage switching solution with capability up to 9 kV.
-
Product
DC Power Module, 8 V, 6.25 A, 50 W
N6732B
Power Module
The Keysight N6732B 50 W basic DC power module provides programmable voltage and current, as well as measurement and protection features at a very economical price. Use this module to power your DUT or ATE system resources, such as fixture control.
-
Product
NI-9423, 24 V, 8 Channel (Sinking Input), 1 µs C Series Digital Module
783735-01
Digital Module
24 V, 8 Channel (Sinking Input), 1 µs C Series Digital Module - The NI‑9423 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each channel is compatible with 24 V logic levels, can accept up to … 30 V discrete logic levels, and has an LED that indicates the status. The NI‑9423 offers isolation between the input and output banks from channel to earth ground. The NI‑9423 is a correlated digital module, so it can perform correlated measurements, triggering, and sychronization when installed in a CompactDAQ chassis.
-
Product
8-CH 24-Bit High-Resolution Dynamic Signal Acquisition Module
PXIe-9529
Signal Module
The ADLINK PXIe-9529 is a high-performance, high density, 8-CH analog input dynamic signal acquisition module. The PXIe-9529 features eight 24-bit simultaneously sampling analog input channels. The 24-bit sigma-delta ADC provides a sampling rate of 192 kS/s at high resolution, making it ideal for higher dynamic range signal measurement. All channels are sampled simultaneously and accept input range up to ??10V, and the analog inputs support software-selectable AC or DC coupling and 4 mA bias current for integrated electronic piezoelectric (IEPE) sensors. The module is especially designed to meet the requirements of vibration analysis and audio testing.
-
Product
PXI/PXIe Wide Current Range Multiplexer Module, Dual 3-Channel, 4-Pole
40-514-101
Multiplexer Module
The 40-514-101 (PXI) and 42-514-101 (PXIe) are low density multiplexers in dual 3-channel, 4-pole configuration. They are capable of switching a wide range of current, from 10 μA to 2.5 A at 220 VDC/250 VAC. The current capability of the module permits the use of a single module type for both low and medium current test applications.
-
Product
PXI/PXIe Microwave Multiplexer, Triple SP4T, 18 GHz, 50 Ω, SMA, Remote Mount, Failsafe
42-785C-423-E
Multiplexer Module
The 40-785C-423-E (PXI) and 42-785C-423-E (PXIe) are triple failsafe SP4T 18 GHz unterminated microwave multiplexers with remotely mounted relays. The 40/42-785C range of multiplexers are available in single or dual, SP6T or SP4T configurations with relays mounted on the front panel. Remote versions are also available which can support up to three multiplexers in a single slot.
-
Product
PXI/PXIe High Voltage Multiplexer, Dual 23-Channel, 2-Pole
40-321-128-HI
Multiplexer Module
The 40-321-128-HI (PXI) and 42-321-128-HI (PXIe) are dual 23-channel 2-pole high voltage multiplexers capable of hot or cold switching up to 1000 V peak. They are also available in a range of bank sizes with 1 or 2 poles and channel counts between 4 and 48. High quality reed relays are used throughout.
-
Product
PXI Very High Density MUX 10 Chan 16 Pole
40-675-002-10/16
Multiplexer Module
The 40-675 series of very high density low cost multiplexer modules are available in a versatile range of switching configurations. The modules are supplied pre-configured in one of six multiplexer modes suitable for signal routing in high channel count ATE and data acquisition systems. The modules use high quality electromechanical signal relays allowing each channel to switch current up to 1A at 150VDC/100VAC. Connections are made via a front panel 200-pin connector.
-
Product
Computer On Modules
COM Express Basic
Computer on Module
COM Express Basic is the latest COM 125mm x 95mm form-factor, including Intel core i, Intel 6th Generation and Intel Atom processor. Because of wide range of processors, Intel core i, Intel 6th Generation and Intel Atom processors, COM Express can provides not only high-speed interfaces like HDMI/DisplayPort, PCI Express, SATA and USB 3.0 for volume data transportation, but also LVDS, PCI, and IDE for legacy applications.
-
Product
PXI Remote Mount Triple SP6T Multiplexer 26.5GHz 50, SMA-2.9
40-785B-533-E
Multiplexer Module
The 40-785B-533-E is a remote mount triple 6-channel 26.5GHz unterminated microwave multiplexer. The 40-785B range of multiplexers are available as a single or dual 6-channel panel mounted multiplexer with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
Product
PXI/PXIe MEMS Optical MUX, Single 2-Channel, Single-Mode
40-855A-112
Multiplexer Module
The 40/42-855A-112 is a PXI/PXIe 2-channel multiplexer with FC/PC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.
-
Product
PXI/PXIe Wide Current Range Multiplexer Module, Single 24-Channel, 1-Pole
40-514-108
Multiplexer Module
The 40-514-107 (PXI) and 42-514-107 (PXIe) are low density multiplexers in dual 12-channel, 1-pole configuration. They are capable of switching a wide range of current, from 10 μA to 2.5 A at 220 VDC/250 VAC. The current capability of the module permits the use of a single module type for both low and medium current test applications.
-
Product
LXI Microwave Multiplexer, SP4T, 7-Bank, 18GHz, 50Ω, SMA
60-803-107
Multiplexer Module
Our 60-803-107 is a 7 bank terminated SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 18GHz. The 60-803 range is capable of supporting up to 14 banks of terminated 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
PXI Dual SP6T Multiplexer 18GHz 50, SMA
40-785B-522
Multiplexer Module
The 40-785B-522 is a dual 6-channel 18GHz unterminated microwave multiplexer. The 40-785B range of multiplexers are available as a single or dual 6-channel panel mounted multiplexer with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
Product
PXI Very High Density Mux 49 Ch 4 Pole
40-670A-022-49/4
Multiplexer Module
The 40-670A series of very high density multiplexer modules feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems. The 40-670 multiplexer may be operated as a conventional multiplexer with break-before-make action when a new channel is selected. In addition multiple channels may be simultaneously selected (not available in 1 pole mode).
-
Product
Single 8 To 1 Terminated 50Ω 600MHz PXI RF Multiplexer
40-763A-001
Multiplexer Module
The 40-763A-001 terminated single 8 to 1 multiplexer is part of a range of RF multiplexers available in the following configurations: dual, quad and octal 4 to 1, single, dual and quad 8 to 1, single and dual 16 to 1 and single 32 to 1. All multiplexers have the option of automatic terminations which offer advantages at system level by reducing the presence of standing waves in the system which can cause degradation in isolation and crosstalk.
-
Product
PXI/PXIe RF Switch, Hex SPDT, 3GHz, 50Ω, MCX
42-870A-106
Switch Module
The 40-870A-106 (PXI) and 42-870A-106 (PXIe) are 50Ω RF switches with 6 separate SPDT relays in a single slot. They have low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The switch banks been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz.
-
Product
PXI/PXIe MEMS RF Multiplexer, Quad 4-Channel, 4GHz, 50Ω, MCX
42-878-242
Multiplexer Module
The module is based on the latest micro-electromechanical system (MEMS) switching technology and has low insertion loss and VSWR. In addition, MEMS devices have a long operational life of >3 billion operations and benefit from an operating time of <20 μs allowing greater test system throughput. The multiplexers have excellent and repeatable RF characteristics beyond 4 GHz with each path having a nominally equal insertion loss.
-
Product
LXI Microwave Multiplexer, 50Ω 4-Channel 5-Bank 40GHz SMA-2.9
60-802-405
Multiplexer Module
The 60-802-405 is a 4-channel, 5-bank RF multiplexer suitable for switching 50Ω signals up to 40GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
Product
PXI Dual 2 x 2 Fibre Optic (M Mode) ST M50
40-860-522-M50
Switch Module
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
Product
8-Ch SPST 12A-250VAC 24VDC Multiplexer with CAN
H620047C2
Multiplexer Module
This module is ideal for switching up to 12A. Composed by eight relays organized in two trees of four with two relays with NC contact available. The module is shielded in order to reduce the radiated interference in high current switchings.
