Serial Interfaces
one conductor one bit at a time data transfer.
See Also: Interfaces, Parallel Interface, Bus Interfaces, UI, MIPI, Interface Adapters, PXI Serial Interfaces, Parallel Interfaces
-
Product
Interface and Isolation
-
Analog Devices offers a wide range of digital interface and digital isolators with iCoupler® technology covering the industry’s field bus and peripheral communications standards. Digital isolators, isolated transceivers, isolated A/D converters and isolated gate drivers utilize the award winning iCoupler® and isoPower® technologies for isolation solutions without many of the constraints found in optocouplers. Find design solutions for interface devices including keypad controllers, level translators, and high voltage protection products (channel protection, fault protection, overvoltage protection), and latch-up proof switches and multiplexers.
-
Product
Serial Device Servers
-
Advantech''s serial device servers, Modbus gateways, and USB Device Server are easy to install and configure, support wired and wireless networking and provide various operation modes to satisfy rigorous industrial automation needs.
-
Product
Ethernet To GPIB Instrument Interfaces
-
ICS's 9055 and 8055 Ethernet to GPIB Instrument Interfaces convert any GPIB instrument into a VXI-11.3 compatible instrument that does not require special drivers and is compatible with the following operating systems: LINUX, UNIX, SunOS, MAC OS X, HP-UX, IBM-AIX and Windows systems with VISA or an RPC library. ICS's 9055 and 8055 use VXI-11 RPC calls for secure communication with virtually any computer. Easily programmed on a PC by making VISA calls or on a MAC/UNIX/LINUX computer with RPC calls. Special drivers are not required. ICS Electronics is the premier VXI-11 device supplier with 100% VXI-11 compliance in every product. To learn more about the VXI-11 protocol and how it benefits your system, download our new VXI-11 Tutorial or a copy of the VXI-11 Specification.
-
Product
4 Serial Communication Channels, Multi-Mode Programmable, Non-Isolated
SC7
-
Module SC7 supports intelligent, full duplex, independent, multi-channels that can be individually software-configured for either RS-232C, RS-422, RS-485, RS-423 (w/data and/or clk bit inversion for MIL-STD-188C unbalanced interface support), or synchronous or asynchronous communications. SC7 is the same as SC1 except SC7 reallocates the pins used for CTS Flow Control as four (4) additional system grounds.
-
Product
PXIe-8510, 2-Port PXI Vehicle Multiprotocol Interface Module
784121-01
Interface
2- or 6-Port PXI Vehicle Multiprotocol Interface Module—The PXIe‑8510 is a hardware-selectable controller area network (CAN) and/or local interconnect network (LIN) interface for developing applications with the NI‑XNET driver. The PXIe-8510 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
Product
PCI Bus Interface
PCI-6713-4IP
Interface
PCI Bus Interface 3.3 / 5 Volt via PLX 9056 33/66MHz High Performance Floating-Point DSP Up to 300MHz system clock. Up to 32Mbytes of SDRAM 4.0 Mbit flash memory for bootstrap program.
-
Product
COM Express Type 7 10GbE SFP+ Network Adapter Card
CEI-2x10G SFP+
Network Interface Controller
- Support up to two 10GbE SFP+ interfaces- Inphi CS4227 inside- COM.0 R3.1 Type 7 compliant- Dedicated for Express-VR7
-
Product
4-Port RS-422/485 Isolated Serial Communications Card
cPCI-3544
Communications Module
- 32-bit CompactPCI®, PICMG® 2.0 Rev 2.1- Plug-and-play, IRQ & I/O address automatically assigned by PCI BIOS- Four asynchronous communications ports with intelligent buffer- Four RS-422/485 ports- 2500 VRMS isolation voltage
-
Product
CAN FD interfaces and Analysers
-
CAN FD Interfaces and AnalysersCAN FD interfaces and analysers with easy to use CAN bus software with optional support for OBDII, J1939, XCP/CCP, CAN transmit, and reading of DBC files.
-
Product
Avionics Interface Technology
-
The modules are available as PXI, PCI, PCI Express, USB, VME, VXI and many more
-
Product
IEEE488 (GPIB, HPIB) PCMCIA Interface Card
GPIB-PCMCIA-XL
-
The GPIB-PCMCIA-XL is the ideal solution for connecting GPIB instruments to mobile computers.
-
Product
Ethernet Parallel Interface
Model 8003
-
* Provides 40 high-power TTL I/O lines.* Fully VXI-11 Compliant plus Raw Socket for easy programming with Visual Basic or C, Agilent VEE and LabVIEW.* Standard board has vertical Ethernet and Digital IO connector on the component side. * Optional Relay Driver board adds 4, 32 or 40 Relay Drivers. • Apply regulated 5 Vdc power through the Digital IO connector.
-
Product
Single Port RS-232 Interface
PCI-COM232
-
Serial ports: 1Configured: Address and interrupt configured through PCI BIOS and supplied driversMax. baud rate: to 460.8 Kbps, software selectable per channel for 115.2, 230.4, or 460.8KbpsSerial modes: 5, 6, 7, or 8 data bits; odd, even or no parity; 0, 1 or 2 stop bitsUART: 16C550 standardInterrupt Status: Each UART interrupt status read from any UARTís Scratchpad RegisterConnector: 37 position D-type with cable to DB-9 (DB-25 optional)Power: +5V only
-
Product
3U CompactPCI Serial Front Removable SATA Carrier for SSDs
SD8-STEEL
-
The SD8-STEEL is a peripheral slot card for CompactPCI® Serial systems. It includes a shuttle for 1.8 or 2.5” SSD or HDD drives. Signal integrity is optimized with 6Gbps SATA drivers. A push button ejection of the drive enables easy swap removal.
-
Product
Analog Device Interface
ADI-123
-
Model ADI-123 Analog Device Interface offers the means of computer interfacing almost on any device whic is provided with dc inputs and/or outputs, for example programmable power supplies and measuring instruments of all kinds.
-
Product
GPIB to I2C and 8-Bit Data Bus Interface
Model 4802
-
ICS's GPIB to I2C Interface Board is an IEEE-488.2 GPIB and HP-IB compatible interface for I2c and SMB devices.
-
Product
PC/104-Plus And PCI-104 8-Port RS-232 Serial Communication
P104-COM232-8 and 104I-COM232-8
-
The P104-COM232-8 (PC/104-Plus) and 104I-COM232-8 (PCI-104) are PC/104-based eight channel RS-232 communication peripherals. Based on the XR17D158, the boards have eight enhanced 16550 UARTs, each with a set of modem signals (CTS, RTS, RI, DTR, DSR, CD). A 460Kb/s rate is guaranteed for all channels with up to 3K Ohm 1000pF loads. All interrupts may be monitored at a 32-bit status register. Each UART has both a 64 byte transmit and a 64 byte receive FIFO.
-
Product
30 GHz Differential Probe with 2.92mm Interface
DH30-2.92MM
Differential Probe
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
Product
SATA Interface
-
SATA interface with multiple form factors including with 2.5", DOM, CFast, mSATA, Slim options.
-
Product
Interface Connectors
-
High durability Interface connectors do not damage the product, side terminal by a special mechanism, and do not lock, making it suitable for automated inspection.
-
Product
Two Port Fibre Channel/MIL-STD-1760E Network Interface Controller
cPCI-HS1760-NCSW-2
-
Avionics Interface Technologies
Integration of Up Fibre Channel and Down Fibre Channel interfaces - Embedded Network Controller (NC) with four priority levels - Two F/AE ports for communication to external devicesInternal four port non‐blocking fabric switch for communication between NC and external devices - Four port non‐blocking Fibre Channel Switch - Meets the requirements of MIL‐STD‐1760E and AS5653 standards - Initialize via the Fast Fabric Initialization (FFI) protocol - ANSI C API enabling complete FC-AE-1553 NC functionality and management - 3U Conduction-cooled Compact PCI module - Designed for extended temperature operations
-
Product
3U CompactPCI Serial 5-slot SSR w/ RTM no Ethernet
1CPCIS-305-R010
-
3U CompactPCI Serial Backplane with 5 CPCI-S.0 slots, system slot right, with rear IO: 1x CPCI-S.0 CPU slot, 4x CPCI-S.0 peripheral slots, with connectors for RTMs in slots 2 to 5, system slot (Slot 5) has one connector for RTM -> 5RJ6 - no Ethernet.
-
Product
3U cPCI Sensor Interface Unit
SIU31
Sensor Interface Unit
NAI's SIU31 is a highly configurable rugged COTS system or subsystem ideally suited for military, industrial, and commercial applications that require high-density I/O, communications, Ethernet switching, and processing. The SIU31 uses one NAI field-proven, 3U cPCI board to deliver off-the-shelf, SWaP-optimized COTS solutions that "Accelerate Your-Time-to-Mission."
-
Product
SparkFun Serial Basic Breakout
CH340C And USB-C
-
This SparkFun Serial Basic Breakout is an easy-to-use USB-to-Serial adapter based on the CH340C and takes advantage of the handy USB-C connector. With USB-C you can get up to three times the power delivery over the previous USB generation at 1.5A and and also solves the universally frustrating dilemma of plugging a USB cable in correctly, because it’s reversible! The Serial Basic works with 5V and 3.3V systems and possesses the capability to auto install on most operating systems without the need for additional drivers. The Serial Basic uses the CH340C IC to quickly and easily convert serial signals to USB.
-
Product
3U OpenVPX Sensor Interface Unit
SIU34
Sensor Interface Unit
The SIU34 is a highly configurable rugged system or subsystem ideally suited to support a multitude of Mil-Aero applications that require high-density I/O, communications, Ethernet switching and processing. The SIU34 leverages NAI’s 3U OpenVPX™ boards to deliver off-the-shelf solutions that accelerate deployment of SWaP-optimized systems in air, land and sea applications.
-
Product
3U CompactPCI Serial FPGA 10-20 ports Industrial Ethernet
SY7-CYCLONE
-
The EKF SY7-CYCLONE is a CPCI Serial FPGA board with front panel connectors for up to 20x100Mbps SPE ports. It can be configured as Ethernet NIC, switch, router, or gateway.
-
Product
Interface & Level Converters
-
Advanced Science and Novel Technology, Co., Inc.
2-channel LVDS-to-CMOS converter (Receiver) and 2-channel CMOS-to-LVDS converter (Transmitter)Optional signal splitter function with selectable inversionOptional DS (Data/Strobe) encoding/decoding for compatibility with Space Wire StandardProgrammable LVDS/CML/ECL Receiver input interfaceTrue LVDS Transmitter output interfaceFlexible selection of enabling and operational modes of the channelsHigh-impedance states of disabled CMOS outputsSingle +3.3V power supplyIndustrial temperature range
-
Product
Automatic Liquid Interface Tension Meter,Surface Tension Analyzer,Oil Interface Tension Meter
-
Chongqing Assen Power Equipment Co., Ltd
Our HTID-1 Automatic Interface Tension Tester is used to test various liquid surface tension and interface tension based on the ring method that is simple and high accurate, which is widely applied in electric, petroleum, chemical, medicine, food, and teaching filed.
-
Product
Conduction Cooled Interface Board Supporting up to 5 Multi Function Channels
EXC-1553PMC/Px(S) / EXC-1553ccPMC/Px(S)
-
MIL-STD-1553, conduction cooled, interface board. Supports up to 4 multi function channels.The EXC-1553PMC/Px(S) and EXC-1553ccPMC/Px(S) are multi-channel (up to four) MIL-STD-1553 interface boards for PCI Mezzanine Card compatible computers.Multi Function:Each channel operates simultaneously as a Bus controller and/or multiple (up to 32) Remote Terminals, or as a Triggerable Bus Monitor. In addition, error injection (BC and RT modes) and error detection (all modes) are supported on each channel.Single Function:Each channel operates either as a Bus Controller, Remote Terminal, or Bus Monitor.NOTE: PxS is NOT compatible to the MCH family of cards.The EXC-1553PMC/Px(S) and EXC-1553ccPMC/Px(S) are supplied with C drivers, including source code, and Merlin+ Windows software.
-
Product
Easy-to-operate Interface
ANALYSIS 3P
-
ANALYSIS 3P (Professional Version) interface consists of main menu, toolbar, property bar, submenu, main display area, numerical table and status bar, which is easy-to-operate.
