Cables
See Also: Cable Assemblies, Cable
-
product
DC/DC Converters & DC/AC Inverters
DC/DC converters and DC/AC inverters are available for voltage conversion. With our DC/DC converters, you stabilize DC voltage, refresh the voltage at the end of long cables, and thus avoid malfunctions in your applications. Use our DC/AC inverter to convert direct current into alternating current.
-
product
FieldFox Handheld Microwave Analyzer, 26.5 GHz
N9918A
26.5 GHz max frequency Carry the world's most integrated handheld analyzer: standard model includes cable and antenna analyzer Expand capabilities with optional VNA, spectrum analyzer, built-in power meter, vector voltmeter, and more Save time by measuring DTF and TDR in the same sweep Simultaneously measure all four S-parameters Make accurate spectrum analyzer measurements ( 0.5 dB) without needing warm-up Calibrate simply with QuickCal
-
product
78-Pin D-Type Female Breakout DIN Rail
40-967-078-F
This termination option is capable of accepting heavy duty connection wires and uses rising clamp screw terminals to minimize the danger of copper strand damage. Users should care take to protect the termination, provide a suitable method of restraining the cables, and ensure appropriate electrical safety precautions are observed.
-
product
High Voltage DC Cable Test Systems
We can offer from ±18kVdc to ±30kVdc units which all have automatic earthing for discharging capacitive loads. They are designed to perform tests on installed cables and jointing systems.
-
product
Short Circuit Locator for Power Cables
A910
The A910 is a short circuit locator designed for fault location in power cables. The instrument measures the ratio of the resistances of the two sections of failed conductor using a four-wire "Kelvin" connection, thus eliminating errors associated with contact resistances of the test leads. With the A910 you can determine if the cable has more than a short and locate the first and the last fault. The instrument locates fault with an insulation resistance up to 5 Mohms in cables that have a total resistance greater than 5mohm (approximately 90 m of 300 sqmm cable) and less than 30 kohms. The distance to fault is measured as a percentage of the total length of cable and is displayed on a large LCD display.
-
product
Flexible MiniPCI Express to PCI Adapter
SKU-034-0X
Flexible MiniPCI Express to PCI Bus Adapter (Adapter) was designed to convert the MiniPCI Express bus into two 32-bit PCI buses. It allows to connect up to 2 32-bit PCI expansion boards to the motherboard MiniPCI Express connector (supports full-size and half-size MiniPCI Express host boards).Adapter includes a PCI adapter, MiniPCI Express host board (full-size or half-size) and PCI Express flat Cable.
-
-
product
Fiber Optic Visual Fault Finder
VFF5
Used to verify continuity, test and find breaks in fibre links, locate pinched fibre strands in termination cabinets, or anywhere fibre optic cables are terminated and subject to mechanical damage.
-
product
Terminal Block and SCSI-II 68 Pin Connector with 2 Meter Cable
U2902A
The Keysight U2902A is an accessory compatible and recommended to be used with the U2300A Series USB Modular Multifunction Data Acquisition and U2500A Series USB Modular Simultaneous Sampling Multifunction Data Acquisition. The pin-outs of the U2902A is dependent on the USB Data acquisition unit that it is working with. For more information, please refer to the data sheet or the user guide of the USB Data Acquisition unit that U2902A is to be used with.
-
product
Hipot Tester
HVA Series
HVA systems detect faults in cable networks in a non-destructive yet efficient way and fulfill all the requirements of modern cable testing.
-
product
Fibre-Coaxial DOCSIS Analyzer
CABLERANGER
DOCSIS 3.0 analyzers for hybrid Fibre-Coaxial networks CABLE RANGER from PROMAX provide all the required measurements to install and carry the network maintenance of those hybrid networks using fiber optics and coaxial cables at the physical layer. The operating frequency range spans from 5 Mhz to 1700 Mhz, thus fulfilling DOCSIS 3.0 and 3.1 requirements.
-
product
50 Ohm SMB to SMB Cable Assemblies - 3GHz
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
product
SH68-68-D1, Shielded Cable, 0.4 m
183432-0R4
68-Pin, Female D-SUB to 68-Pin, Female D-SUB, Twisted Pair, Shielded Digital Cable - The SH68-68-D1 Digital Cable connects NI 6533/4 digital instruments and NI 660x or 661x counter/timer modules to 68-pin accessories. This shielded cable features twisted pairing and is offered in different lengths.
-
product
25-Pin D-Type Female Straight PCB Mount
40-963-025-SF
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires. 25-Pin Female connectors can be directly mated to a corresponding Pickering Switching Module while Male versions can be used to interface to a Female cable assembly termination.
-
product
Cable Test Van
ETL-35K
ETL-35K system has a multitude of applications in electrical equipment testing and maintenance: testing cable insulation with DC (rectified) voltage up to 60 kV, measuring small leakage current of surge arrestors, high-voltage testing with AC voltage up to 100 kV at industrial frequency, underground utilities tracing, cable fault pre-location and pinpointing, and measuring capacitance and tan delta of various electrical objects at industrial frequency.
-
product
Insulation Meter
HT7051
HT7051 has been developed to measure insulation resistance with test voltage programmable up to 5kVDC and measuring range up to 10TΩ which makes it very useful in any industrial application (tests on electric machines, power transformers, electric cables, electric boards, generic devices, etc.) within BT.
-
product
Remote Cable Tester for RJ45 RJ11 USB and BNC
REMOTETEST
Troubleshoot your wiring problems, quickly and affordably with StarTech.com's REMOTETEST, a Specially designed network wire tester that saves valuable time and effort when testing RJ45, RJ11 and BNC cables.
-
product
Cable Assembly, 160-Pin DIN41612, Female to Unterminated With Ferrules, 1m, 45º
A1604F5-F-0A100
For applications where a 45 degree cable exit would be preferred with unterminated connections at the other end. The cable assembly is constructed from highly flexible 7/0.15 (26AWG) Silver Plated Copper Wire. If the user requires the connector to have a second fixing then the right hand connector can be fitted with the optional screwlock assembly 40-969-101.
-
product
Cable Assembly, Receiver, 20", Mini Coax, 20 SMA Plugs
540129010109
Cable Assembly, Receiver, 20", Mini Coax, 20 SMA Plugs.
-
product
Off-Card Adapter,
3910-FOFE
As the physical size of Fibre Optic Front End (FOFE) transceivers prohibits their use on PCI, CompactPCI, PMC and ISA (PC/AT) cards, Western Avionics provides an off-card Adapter, that contains all components to support the 3910 Optical implementation of STANAG 3910. The 3910-FOFE Adapter provides a complete dual redundant optical interface, together with dual redundant 3838 connections, and Trigger-in and Trigger-out in a minimal sized package, to allow convenient cabling connections to the 3910 / 3838 system or unit-under-test.
-
product
30 A, 10 MHz Current Probe - AC/DC, 30 A rms, 50 A Peak Pulse, 3 Meter Cable
CP030-3M
Teledyne LeCroy current probes are available in a variety of models for a wide range of applications. The full range of Teledyne LeCroy current probes includes models with bandwidths up to 100 MHz, peak currents up to 700 A and sensitivities to 1 mA/div. Teledyne LeCroy current probes are often used in applications such as the design and test of switching power supplies, motor drives, electric vehicles, and uninterruptible power supplies.
-
product
8-Pin Power D-Type Cable, Male to Unterminated, Cut Ends, 1m
40-972-408-1m-MU
The 8-Pin Power D-Type Connector to Unterminated Cable Assy is constructed from PVC insulated 56/0.3 (12AWG) Copper wire. The connector can be secured to the product by screwlocks and the unterminated connections are coded to match the connector pin designation.
-
product
Cable Assembly, Receiver, 20/26GHz Coaxial, 36", 8 SMA Plugs
540259010253
Cable Assembly, Receiver, 20/26GHz Coaxial, 36", 8 SMA Plugs
-
product
Cable Assembly 44-Pin D-Type Male to Female, 1m
40-970-044-1m-MF
The 44-Pin D-Type Density and a Half cable assembly is constructed from 7/0.15 (26AWG) Silver Plated Copper Wire with PFA insulation. Screwlocks are provided to secure the connectors to their associated products.
-
product
Temperature and Humidity Regulator
H3431-4
Relative humidity, temperature probe on a cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy. Three two-state inputs.
-
product
PCB Adapter, ITA, SIM, VTAC, 16 Pos, 6 Slot, to (1) Cat6
510171105
A small, modular PCB board that connects high speed digital inserts (VTAC) to a single Cat 6 connector. Great for COTS cable configurations. Compatible with all VTAC/SIM ITA modules. Please note this part is too wide for use in multiple adjacent slots.
-
product
Cable Assembly, Receiver, QuadraPaddle, 36", 2 78-Pin Female D-Sub
540034010229
Cable Assembly, Receiver, QuadraPaddle, 36", 2 78-Pin Female D-Sub
-
product
Cable Assembly, Receiver, Mini Coax, 20", 4 BNC Plugs
540064010107
Cable Assembly, Receiver, Mini Coax, 20", 4 BNC Plugs
-
product
CapaConnect repair defective capacitive string parts
CC-LRP3/4+KS+DS
Hachmann Innovative Elektronik
With modules of CapaConnect series you can repair defective capacitive string parts of older installations, or retrofit string parts, where until now only direct cable taps are available. The connections to coupling dielectrics and earth can be carried out without an expensive dismantling normally, as the module contains all necessary components, like surge arresters, plug-in positions for adjustment capacities and high-quality contacts.
-
