Line Fault Indicators
See Also: Overhead Line
-
Product
Programmable Delay Line Instrument
XT-100-OEM
-
With the XT-100-OEM, all the capabilities and precision of the XT-100’s trombone technology can be built right into your own system. This product is intended primarily for OEM applications so you have a streamlined solution for precision phase shift or programmable delay.
-
Product
Phase Sequence Indicators (Contact Type)
855 PRA
-
Standard Electric Works Co., Ltd
● Two functions in one unit: open phase and phase sequence detection.● Lamps let you determine at-a-glance if phase is open.● Large size alligator clips for easy clipping onto switch-boards terminals.● Checks a wide range of 3-phase power sources.● Special test leads length are available on request.● Push button switch is designed to minimize damage due to negligence.
-
Product
Line Input Test
-
Measure the dB level and frequency of the iAudioInterface2 line input or line output (also works with any dock input audio source).
-
Product
Bleeder, Pressure Indicator - Brake, F/A-18 Hornet
74D130017-1001
-
F-18 Brake Bleeder. This unit is designed to test, monitor and bleed the brake systems of F/A-18 Hornet fighter aircraft.
-
Product
Dual Bus 64-Channel 2A PCI Fault Insertion Switch
50-190-102
Fault Insertion Unit
This PCI fault insertion switch range is available with 75, 64 or 36 channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. The Stimulus/Measurement to UUT path is suitable for supporting CAN and FlexRay bus systems.
-
Product
Digital Tap Position Indicator With Voltage &Counter Display
-
NMC''s latest offering digital tap position indicator with voltage and counter display, type: TX-204, is a fully micro controller based instrument used to indicate the tap position of the power transformer also indicating the voltage and counter indications simultaneously at a same time.
-
Product
Single Sensor - Monochrome Line Scan Cameras with Fast Scan Rates
-
JAI’s monochrome line scan cameras provide an excellent combination of high resolution and fast scan rates.The Sweep SW-8000M-PMCL model features an 8192-pixel linear CMOS sensor delivering a line rate of 100,000 lines/s (100 kHz) over a Camera Link interface. The SW-4000M-PMCL model is based on a 4096-pixels sensor capable of running as fast as 200,000 lines/s (200 kHz) over Camera Link.
-
Product
Continuity Tester with Audible & Visual Indication
TEK404
-
The Martindale TEK404 is a low cost, easy to use continuity tester. It has audible and visual indication plus overvoltage protection. It has the same loud buzzer as the TEK402, giving a very clear signal of continuity.
-
Product
Power Line Communication (PLC) Module For Single Board Computer
MIOe-PLC
Single Board Computer
Dual QCA7006 for EVSE / Charging Station sideEthernet Host Interface, SPI OptionalExtended Operating Temperature -40~85° C
-
Product
Pen-type Visual Fault Locator (VFL)
JW3105A
-
Shanghai Joinwit Optoelectronic Tech,co.,Ltd
JW3105A VFL is specially designed for field personnel who need an efficient and economical tool for fiber tracing, fiber routing and continuity checking in optical network. It includes:
-
Product
Power Quality Measurement & Digital Fault Recording
-
In view of the growing number of factors with a disturbing influence on power systems and the ever increasing sensitivity of devices and installations on the consumer side, simple monitoring criteria such as undervoltage or overcurrent are no longer adequate. Reliable registration of all the relevant processes within the electrical power system calls for constant observation of a wide variety of derived parameters, such as individual harmonic content, system unbalance and interharmonics, and the swift identification of even slight deviations from the norm.
-
Product
Programmable Delay Line Instrument
XT-100
-
The latest generation of the product that started it all. The XT-100 features Colby's patented trombone technology for unmatched precision and ease of use. Using delay extensions, the XT-100 also comes in a number of configurations that give you the range you need, up to 100 ns.
-
Product
PXI Fault Insertion Switch, 6-Channel, Two Fault Buses, 30 A, Hardware Interlock
40-191B-012-HI
Fault Insertion Unit
The 40-191B-012-HI is a PXI fault insertion switch with hardware interlock using solid state switching elements and is capable of carrying 40A on single channel or 30A on all channels at the same time and provides a robust solution to high current fault insertion.
-
Product
FAult Detector and OScilloscope 9 Functions in 1
FADOS9F1
-
Prot-Ar-Ge Industrial Project Design R&D Ltd. Co.
2 unique features are added to the FADOS9F1 over the FADOS71. First feature is the Programmable DC Power Supply; It can be adjusted between 0-16V and 20-1500mA with power output; the DC Voltage/Current graphs of the electronic card power supply can be produced. The second feature is the “IR Remote Temperature Measurement Sensor”; this sensor is used to find the components that heat up by drawing too much current. Using these two features together may reduce the time for trouble shooting some malfunctions by 5 to 10 times. These features can be used as a new technique for trouble shooting.
-
Product
Line Scan Cameras
-
JAI’s extensive product offering includes color line scan cameras featuring prism technology with multiple CCD or CMOS linear sensors delivering high performance color/NIR imaging solutions for high-speed web/continuous applications such as print verification, tile inspection, food/fruit sorting, and more. Also monochrome line scan cameras with ultra fast scan rates.
-
Product
Classic Collet | Black | With Line | Matt Or Glossy | Ø 21 Mm
021-4x20/5
-
Secure plastic mounting cap for collet or wing knob
-
Product
Detection of Earth Faults (PtG) and Short Circuit (PtP) Faults
CableTroll 2330
-
CableTroll 2330 is an indicator for detection of earth faults (PtG) and short circuit (PtP) faults on multi and single core cable terminations. The unit uses NorTroll type current sensors.
-
-
Product
Wing Knob | Gray | With Line | Matt Or Glossy | Ø 28 Mm
023-5x10/5
-
Secure plastic collet mounting wing knob with cap
-
Product
Cable Fault Locators
-
Cable Fault Locator is a device used for short circuit faults, cable cuts, resistive faults, intermittent faults, and sheath faults. Fiberinthebox supply cable fault locator for power cable, optical fiberal cable, etc. Fault Location in Power Cable is designed to locate cable faults, pinpointing the fault location, route tracing, cable identification, voltage withstand test and cable information management. It can locate all kinds of cable faults for all voltage level cables, including open circuit, short circuit, low insulation, high insulation and flashover faults, etc. Most power cables were buried underground, invisible, and out of reach, with modern new power cable fault locater, it can find the fault point quickly, solve problems immediately and restore power supply.
-
Product
TestPort Line Of Hand-Held Ethernet Test Equipment
-
The TestPort line of handheld Ethernet protocol test tools represents the state-of-the-art test equipment for telecom backhaul networks. It’s protocol support includes Gigabit Ethernet (GbE), Sychronous Ethernet (SyncE), and E1. Testing applications include protocols analysis, traffic generation, and impairment testing.
-
Product
Altitude Indicator and Pressure Transducer
AI100
-
Bemcos AI100 Altitude Indicator and Pressure Transducer provides a red, 5-digit scaled LED display of chamber or process Altitude, calibrated in feet or meters as well as a linear, scaled output of 4 to 20 mA, 0 to 5 VDC, or 0 to 10 VDC for use with other instruments including process controllers, recorders, and programmable logic controls.
-
Product
Coupling Decoupling Network for Communication Lines
CDN61000-5C
-
• Application Range: ≤4kV, 1.2/50us pulse, 8 wire unshielded twisted pair (UTP) • Test Voltage: Max 4KV, 2 kV (1.2/50 µs pulse when RJ45 connector is connected. Maximum test voltage is 1.5kV when RJ45 female is unconnected or auxiliary terminal is not protected.) • Coupling mode: 90V gas- discharge tube+250ohm Resistor/Each Wire, 8 Wires Simultaneously-Ground (Common Mode) • Input and output interface: RJ45 connector • Terminal layout (RJ45 connector): First pair of lines: pins 1/2 Second pair of lines: pins3/6 Third pair of lines: pins 4/5 Fourth pair of lines: pins 7/8 • Max. operating speed: 1000MBit/s • Max operating voltage: Max 50V DC • Max operating current: Max 1A Related Instruments
-
Product
- Optically Isolated Line Driver
Model 72A
-
FEATURES: DC TO 19.2 KBPS; Optically Isolated; TD & RD LED's; Loopback Switch; Built-In Surge Protection; Male or Female Connectors; Screw Terminals and RJ-11. The Model 72A Optically Isolated Line Driver links RS-232 based devices over extended distances. It provides optical isolation and has built-in verification of operation using a loopback switch.
-
Product
Phase Sequence Indicators (Contact Type)
887 PR
-
Standard Electric Works Co., Ltd
● Indicates phase rotation. ● Indicates phase presence.● No battery required.● Phase rotation phase presence indicated on large liquid crystal display.● Small, rugged enclosure.● Color coded test leads.● Phase presence indication from as low as 40Vac to as high as 600Vac.● Fused.● Lightweight, robust and compact.● EN 61010-1 CAT III 600V EN 61010-2-032
-
Product
PCI Fault Insertion Switch Cards
-
Pickering's PCI Fault/Signal Insertion Switch Cards feature a breakout arrangement that allows faults to be attached to the sensor lines, this includes the breaking of a connection or the adding of defect all of which can simulate connectivity problems in the system.
-
Product
Single-in-Line Reed Relays
Series 116
-
SIL relays - Smallest board area. 1A version requires 0.15 x 0.27 inches .(3.8mm x 6.8mm). 1 or 2 switches with 10 Watts rating. 5 or 12 Volt coils with optional diode
-
Product
Fault Locator
SNOOPi
-
SNOOPi employs a bespoke optical sensor to detect and discriminate between fault and natural gas.
-
Product
Step-Tunable Laser Source, High Power and Low SSE, Basic Line
N7779C
Laser Source
The new N7779C basic line step-tunable laser source is ideal for cost-effective testing of broadband optical devices. It can also serve as a highly stable, tunable local oscillator for receiver testing or transmission experiments.
-
Product
High Soeed CMOS System on Chip (SoC) Line Scan Image Sensor
LS4k
-
The LS4k is a high speed CMOS System on Chip (SoC) line scan image sensor optimized for applications requiring short exposure times and high accuracy line rates. It incorporates on chip two pixel arrays consisting of 2 rows with 4,096 7µm pitch pixels and 4 rows with 2,048 14µm pitch pixels respectively, a high accuracy (12-bit) high speed (84MHz) analog-to-digital conversion (ADC), and sophisticated on chip optical calibration for PRNU, DSNU, and lens shading correction.
