Statistical Process Control
Monitoring, controlling and, ideally, improving a process through statistical analysis.
-
Product
Linear Actuator Controls
AC-063
-
Thomson offers the AC-063 control for use with its Electrak PPA, Electrak 10, and DMD actuators. Rugged and robust in design while operating under the hardest of conditions with a tough plastic enclosure. Variations include AC or DC inputs, with or without limit switch inputs, and with or without control pendants.
-
Product
Large Flow Liquid Source Vaporization Control System
LE Series
-
A high-flow, high-efficiency, liquid vaporizer with flow channels and heater elements embedded in a cast aluminium block which ensures maximum heat transfer, and the elimination of both cold spots and the risk of condensation. This Liquid Source Vaporization Control System can operate at up to 300 °C and can vaporize up to 30g/min of IPA (or equivalent).
-
Product
CCCP Controller
-
CCCP is the technology behind Nüvü Camēras’ extraordinary sensitivity in low light imaging. The patented controller generates significantly less clock-induced charges (CIC) than any other CCD controller during charge transfer throughout the EMCCD (down to an average below 0.001 ē/pixel/frame), therefore allowing for greater EM gain to ultimately attain sub-electron readout noise.
-
Product
Gas Detection System Controller
SMC Sentry IT
-
The SMC Sentry IT Controller is a powerful network-enabled hazardous gas detection system that operates up to 32 detectors and interfaces with devices over Modbus RTU, 4-20 mA, Sentry PSG Bus, and conventional dry contact. The embedded web application enables users to view important data remotely and provides connectivity into the Industrial Internet of Things (IIoT).
-
Product
ISA Optima Motion Controllers, 1-8 axes
DMC-1700
-
The DMC-1700 for the ISA bus is a member of the Optima Series, Galil's full-featured multi-axis motion controllers. Designed to fit in a single ISA slot of a PC, the DMC-1700 controllers accommodate 1- through 8-axis formats and allow control of step or servo motors on any combination of axes. Any mode of motion can be programmed including linear and circular interpolation, contouring, electronic gearing and ecam.
-
Product
Conductivity Type Level Controller
ULP-29
-
Unitech Scales And Measurements Pvt. Ltd
Unitech make conductivity type level controller comprises of a measuring tank made of acylic materials.
-
Product
Temperature Controller Data Logger
-
We manufacture qualitative Siren Unit which is a time switch that controls factory / school / college / hospital bells. In a factory siren is set as per the timings such as starting of shift, end of shift, lunch time and other events. The unit can be programmed for the weekly holidays so that siren remains off on those days.
-
Product
PCIe 3.0 Ethernet Controller
BCM57416
-
The BCM57416 10GBASE-T PCIe 3.0 Ethernet controller builds upon the success of the widely-deployed NetXtreme E-Series architecture by combining a high-bandwidth Ethernet controller with a unique set of highly-optimized hardware acceleration engines to enhance network performance and improve server efficiency.
-
Product
DC Electronic Load Control Software
EES-100-xx
-
EES-100 Software controls all electronic load types. ( Single & Dual channel) data logging, constant current, constant voltage, constant power, constant resistance, up-down timing, V/I Curves, Graphing, Response Testing
-
Product
Tested Wireless Controller Software
AssureWave Testing
-
The AssureWave program provides stringent testing of client and application interoperability on Cisco''s Unified Wireless LAN Controller infrastructure.
-
Product
Digital SINE Controller
DVC-4/8 SINE
-
RANGE: 2 to 6250 Hz, digitally synthesized.STABILITY: +/- 100ppm/C, crystal-controlled.DISTORTION: <0.50% thd 0.25% typical.LIMITS: Sweeps between programmed upper and lower limits.
-
Product
SAFE-T-GROUND - Ground Continuity Monitor / Control
TR-7
-
Model TR-7 Safe-T-Ground provides continuous monitoring of a truck's ground connection throughout loading operations. Static electricity is often brought in by tank trucks entering the loading area. The Safe-T-Ground Model TR-7 instantly stops loading operations if a tank truck loses its ground.
-
Product
XMC Display Control Card
XM61002
-
LinkedHope Intelligent Technologies Co.,Ltd.
XM61002 is an XMC display control card independently developed by Linghao Intelligent®. It is mainly targeted at high-performance embedded graphics image processing and GPU general computing processing (GPGPU) applications.
-
Product
Torque Control System
HD-Series
-
The Mountz torque and automation control system is a revolutionary change in repeatable screw fastening technology. The patented HD-Series hybrid system is the world's first torque control tool using both air and electric power to set and control torque. The HD's precise pneumatic pressure sensor and patented algorithm allow for precision digital torque selection. It provides real-time monitoring and torque control of the tightening process. It provides repeatability of the torque applied to screws, regardless of joint characteristics and frictional differences in actual applications. Affordable, flexible system that can replace up to 8 conventional screwdrivers.
-
Product
PCIe To PXIe Remote Control Interface Kit, 5m Cable
43-921-052-KIT
-
The 43-921 PCI Express-to-PXI Express expansion kit provides control of PXI Express modules installed in a PXI Express chassis using high bandwidth PCI Express technology. The extension kit can provide up to 4GB/s using PCIe Gen 2 x8 signaling. The 43-921 PCI Express-to-PXI Express expansion kit provides additional PXI instruments slots to the host computer by implementing a PCI Express-based control of PXI modules. The technology consists of a 53-921-001 host adapter installed in the host computer, a PCIe x8 cable, and a 43-921-00x, a remote controller with the 3U (Eurocard) expansion module. 53-921-001 comes in a PCI Express x8 footprint and equips with PCIe x8 cable connector.
-
Product
SPS Digital Controls
-
With 35 years of proven experience in design and manufacture of precision positioning systems, CAES provides SPS Digital Controls for commercial and military applications with the best combination of reliability, precision and value.
-
Product
Fast Response Flow Controller for Low Flow
HFM-300 / HFC-302
-
The all metal HFM-300/HFC-302 is Teledyne Hastings' metal sealed, fast response series of mass flow meters and controllers. Featuring reliability and stability, the 300 Series is chosen by OEM's for its fast response under a wide range of conditions.The HFM-300 / HFC-302 meters and controllers have flow ranges from 0-5 sccm to flows of 0-25 slm; provide analog outputs, are constructed of stainless steel and have normally closed valves. The full scale range is specified by the end user. A NIST traceable calibration certificate is standard. Corrosive gases and pressures up to 1000 psig are easily measured. Cleaning for oxygen service is available.
-
Product
Process & Material Characterization System
TriboLab CMP
-
Bruker’s TriboLab CMP Process and Material Characterization System has been designed from the ground up specifically for reliable, flexible, and cost-effective bench characterization of waferpolishing processes. Small R&D-scale specialty system for CMP. Reproduces full-scale wafer polishing process conditions without downtime on production equipment. Provides unmatched measurement repeatability and detail. Allows testing on small coupons for substantial cost savings over whole-wafer testing.
-
Product
Industrial Panel Controls
-
Panels controls are designed for applications that typically require frequent adjustment. Both rotary and slide panel control types are available. A selection of elements includes carbon, cermet, and conductive plastic. These devices are available in various sizes and shaft/bushing combinations. Some models are available with a rotary switch and seal options. Typical applications include audio mixing consoles, test and measurement equipment, consumer electronics, and medical equipment.
-
Product
Digital Weighing Indicator | Process Meter | Panel Meter
-
Mantracourt’s digital weighing indicator and panel meter modules are compatible with a wide range of sensors and transducers, including volts, amps, temperature, frequency, speed, load, force, pressure, torque, LVDT, RVDT and many more. The digital architecture offers simple one-pass calibration and fast setup.
-
Product
Flow Control Set Up Using PID Controller
ULP-25O & ULP-25T
-
Unitech Scales And Measurements Pvt. Ltd
Flow Control Setup Comprises of a Orifice with DPT to measure flow Rate. The flow of water is controlled by Control Valve with pneumatic actuator. I to P converter is provided to control the actuator. Rotameter is provided to measure actual flow rate. The system is mounted on a table top model with all necessary piping.
-
Product
One Channel Gas Controller
MX 16
-
Teledyne Gas & Flame Detection
Specially designed for applications in laboratory, storage, small boiler room, and breweries or battery charging rooms, the MX 16 measuring unit prevents the risks of explosion linked to the presence of toxic, anoxic and explosive gases in the ambiant air. Small size, ease of installation and use are the main strengths of the plant. Used with the OLCT 10N O₂ and CO₂ digital sensor series or any other O₂, CO₂, CH₄, GPL and H₂ analog sensor, the MX 16 guarantees you a solution that complies with French and European standards.
-
Product
[5kV AC/6kV DC] Hipot and Insulation Resistance Tester, Rise/Fall-Time Control Function Equipped
TOS5300 Series
-
The "TOS5300 Series" is a series of test instruments used in Hipot (withstanding voltage) tests and insulation resistance tests, two of the four tests regarded as necessary for ensuring the safety of electrical products. With an output of 5 kV/100 mA (AC) and 6 kV/10 mA (DC), the series can be used in Hipot (withstanding voltage) & insulation resistance testing of electronic equipment and electronic parts, based on the requirements of IEC, EN, UL, VDE, JIS, and other international safety standards and the Electrical Appliance and Material Safety Law. Also, the test voltage stability is improved with the adoption of a newly developed switching amplifier. Since the output voltage can be kept constant even when the AC line voltage or frequency changes, consistent testing can be performed, even when the power supply environment is in an unstable region. The TOS5300 is also equipped with a number of features that are capable of meeting a variety of test needs. It is a new low-cost standard model that provides thorough operability, reliability and safety.
-
Product
Quality Control for more Precision in Press Hardening
PRESS-CHECK
-
The automated test system PRESS-CHECK works with two powerful high-end thermographic cameras for continuous measurement of two-dimensional temperature distribution. This measurement is carried out before the pressing operation on the surfaces of the boards to be processed and subsequently on the resulting molded parts, ultimately enabling exact compliance with the thermal process parameters.
-
Product
MOTORIZED VARIABLE TRANSFORMER CONTROLLED POWER SUPPLY
-
Motorized Variable Transformer Controlled Power Supply, P/N 18534PSInput: 460 VAC, 3 PH, 60 HzOutput: 0 to 250 VDC, 200 Amp max.Variable Transformer is used to vary the output. SCR controller is not used, as it generates harmonics.Input control is 0 to 3.6 VDC.Indoor enclosure.Output voltage and current feedback as 4/20 mA for PLC interface.All input/output connections are inside the enclosure
-
Product
Digital Timing and Waveform Controller
Ice Bloc DCS
-
Ice Bloc DCS is a highly versatile sequencing system with multiple high-speed digital I/O, analogue outputs and a four-channel digital synthesiser. The DCS sports both single-shot, burst and infinite loop sequence capability. Designed to handle the demands of experimental control required for cold atom experiments, its compact form factor with customisable software interface allows easy integration with your experiments .
-
Product
sbRIO-9871, Non-Enclosed, 4-Port, RS485/RS422 C Series Serial Instrument Control Module
780879-01
Interface Module
The sbRIO‑9871 adds RS485/RS422 serial ports to CompactRIO systems. The serial ports are accessed directly from the FPGA to offer you flexibility in communicating with serial devices. The module has individual buffers on every port that save FPGA space and simplify programming. The sbRIO‑9870 supports standard start bit, stop bit, and handshaking settings. It uses an external power to provide maximum compatibility and reliability under all serial port conditions. Non-enclosed modules are designed for OEM applications.
-
Product
VPX Processing System
CRS-D4I-3VB1
System
4-slot, SWaP-reduced, rugged VPX Intel base plate cooled data processing system that can be applied across various applications including civilian and military unmanned vehicles, manned commercial and military aircraft, helicopters, over- and underwater research vessels, ground vehicles, and locomotives.
-
Product
Control Unit
Epec 4602
-
Epec 4602 Control Unit has a wide range of programmable I/Os for different implementations. Epec 4602 can control 10 hydraulic blocks simultaneously by using 20 PWM outputs and 10 feedbacks. It can be used as a stand-alone controller or as part of decentralized control system.
-
Product
HDC Torque Controllers
-
The HDC controllers operates with only the HD-Series automation electric screwdrivers. It is a single tool controller that offers programmable speed, angle, auto reverse and soft start options. The controller provides programmable fastening options for sequence based assembly automation applications. The patented HD-Series hybrid system is the world's first torque control tool using both air and electric power to set and control torque. The HDC precise pneumatic pressure sensor and patented algorithm allow for precision digital torque selection.
