Mobile App Testing
See Also: Mobile App
-
-
product
Automated Switch Test Equipment
TRICOR Systems Inc. offers test equipment for switches, keypads, rubber, etc. Virtually any component where accurate force-displacement and measurements are required. From our Model 933A, a low cost life test system to our Model 925 test station used to obtain precise force measurements relative to displacement; we have the system you require.
-
product
Encoder Testing
HEIDENHAIN offers testing and inspection devices for the adjustment and fault diagnosis of its encoders. The highly accurate inspection devices are universally deployable, capable of being calibrated and interposed within the closed control loop. The testing devices are primarily used for the functional testing and adjustment of encoders. HEIDENHAIN encoders deliver all of the setup, monitoring, and diagnostic data needed.
-
product
Transportation Bounce Test System
KRD51 series
Bounce testing simulates the constant loose cargo state during truck transport. Often times, containers carrying military and civilian hardware (such as: medical supplies, electronics, weaponry, communication devices) travel for extended periods of time and must be transported off-road. All of these items must maintain functionality upon arrival at their destinations.
-
product
Flight Termination Test Set
Kratos Defense & Security Solutions, Inc.
The FTTS accepts AC power and generates a modulated RF output suitable for interrogation of flight termination receivers and/or command receiver/decoders. The FTTS can transmit up to 6 tones simultaneously and the RF output power is adjustable from 0 to -127 dBm. The IRIG tones can be switched ON/OFF independently from the control panel. A 20 Tone version of the FTTS is also available.
-
product
Exchangeable Test Fixture
MA 2112/D/H/S-7
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 11,30 kg
-
product
Testing & Measurements
Kiwa Dare performs measurements and tests in the area of CE marking, Automotive and FCC. The laboratory is specialized in EMC, RED and Product Safety tests for household, industrial, automotive, medical, telecom, maritime, railway, aerospace and military equipment.
-
product
Generates Test Cases on ICE
TrekSoC-Si
TrekSoC-Si automatically generates self-verifying C test cases to run on the embedded processors in SoCs in in-circuit emulation (ICE), FPGA prototyping, and production silicon. This verifies your chips more quickly and more thoroughly than hand-written diagnostics or running only production code on the processors. TrekSoC-Si's generated test cases target all aspects of full-SoC verification and work in a variety of different environments. TrekSoC-Si is a companion to TrekSoC, which generates test cases for simulation and acceleration. TrekSoC-Si extends the benefits of TrekSoC into hardware platforms.
-
product
Pressure Test & Calibration Pumps
Pressure Test Pump is a hand operated pressure pump designed to generate pressure from 95% vacuum to 1,500psi (100bar). A high-quality screw press is designed for fine pressure adjustment, with an adjustment resolution up to 10 Pa (0.1 mbar). A specially designed shut-off valve makes the pressure as stable as possible during calibration. A built-in gas-liquid isolator protects the pump from moisture and dirt to reduce the need for maintenance. Two hand-tight quick connectors installed on the pump allow easy connecting and disconnecting to the test pump without the need for PTFE tape or wrenches. The 918 is an ideal comparison test pump for pressure instruments calibration.
-
product
Test Studio Dev Edition
Test Studio Dev Edition is a Visual Studio extension allowing software engineers to create functional automated UI tests in Visual Studio using C# or VB.NET. It is designed to provide ready-to-use Visual Studio automated testing functionality across web and desktop. Applications that are built with the Telerik and Kendo UI controls can be automated in a snap, by way of built-in native component translators.
-
product
Electrical Test & Measurement Tester
Evolusys Technologies Sdn. Bhd.
• Polarity • Forward & Reverse Voltage• Forward & Reverse Current• Snapback/Thyristor• Open/Short measurement• Contact check (optional-apply for Keithley C series only)
-
product
Telephone Test Sets
Telephone test sets are a standard among telephone linemen. For the past 100 years, a test set’s functionality hasn’t changed much. Times are changing, networks are changing and now butt sets are changing. No longer are they single-purpose tools but are evolving into full-fledged, multi-functional test sets. Enter Fluke Networks’ newest line of VDV (voice, data and video) telephone test sets. We’ve taken the best features from our existing line, added new technology and totally redesigned them to lighten up your tool belt.
-
product
RAMP TEST SET
AN/USM-719
Tel-Instrument Electronics Corp.
Based on entirely new up-to-date technology and digital architecture; the AN/USM-719 large 4.75" x 3.5" in. color LCD screen and surrounding soft-keys and keyboard provides easy and quick access to a multiple of test screens menus, and display options affording single man operation, instant results, and a host of pre-programmed and manually variable parameters to meet the most demanding requirement's for testing of advabced airborne avionic and transponder/interrogator systems.
-
product
Test Adapter
FECVF1600
Frothingham Electronics Corporation
The VF1600 Test Station is a high current forward pulser designed to be used in conjunction with our FEC200E tester. This gives you all the versatility of the proven FEC200 with the addition of much higher forward current. The VF1600 station can produce a maximum current of 1600A at up to 5V using an 8.3 mS half sine waveform at the built in test station, and THETA and DVF tests at up to 500A at 10mS pulse width. It is derated for wider pulses. For rectangular VF pulses at 300us or 1ms, it can produce up to 2000A. The station can also test all of the usual FEC200 tests in the same test program.
-
product
Valves Testing Equipment
A PD or PHD Pinhole Detector is ideal as it has an audible alarm which sounds when a fault is found. Additionally, the test voltage can be set accurately, which is particularly important when testing thin linings. A DCCT mains-powered porosity tester can be used if the process needs to be incorporated into a production line
-
product
Parametric Test Solutions
Reduce your cost-of-test up to 20% with our ultra-fast CPU Overcome your process test challenges Boost measurement throughput and lower costs with our synchronous/asynchronous parallel test capability Better low-level measurement performance Create customized waveforms Reduce transition costs
-
product
DC High-Voltage Test Device
PGK 25
Cable testing with the BAUR PGK 25. Cables must be tested in compliance with the national and international standards. This applies before the commissioning of new cable networks. The portable BAUR PGK 25 cable test device is used for DC voltage testing in low- and medium-voltage cables. It is characterised by its low weight of only 16.5 kg, by the easy operation and solid construction for onsite use.* Compact device for DC voltage testing with negative polarity* Continuously adjustable output voltage* Perfect for mobile use
-
product
Compact Ultrasonic Testing Device
SONAPHONE® Pocket
With the SONAPHONE Pocket you identify problems even before they arise and create value at all levels of your company. Just by detecting and eliminating leaks you can reduce the energy costs for your compressed air system up to 30 percent. This also has positive effects on your operational safety and system productivity through early warning of bearing failure and evidence of partial electrical discharges.
-
product
Battery Test and Analysis System
BTAS-16
The task of testing an aircraft’s Nickel-Cadmium batteries is complicated and involved because of the high number of cell voltage readings that need to be taken during testing. Taking voltage readings from all 20 cells in the typical nickle-cadmium aviation battery multiple times is laborious and error prone, but must be done to properly estimate the condition of the battery under test.
-
product
Functional Test System
TS-5040
The Keysight TS-5040 Functional Test System is a cost effective, robust and reliable test system that gives you the lowest cost of ownership. In addition, the open architecture Test Exec SL gives you the flexibility to do just about anything you want.
-
product
V2X Test Tools
Validate and verify your V2X application with our Mx-Drive Mobility Simulator. Use the Mx-DSRC Compliance tester for USDOT certification.
-
product
Material Testing
A respected and established technique that is used to ascertain both the physical and mechanical properties of raw materials and components.
-
product
Cell, Module & Pack Testing
Cell, Module and pack battery formats are crucial for electrification in transportation and energy. Arbin Instruments' test equipment is designed for performance-based tests, to meet the needs of these complex formats.
-
product
Test Accelerometer Sensitivity And Noise Test
Accelerometer Test Unit
*Quick and Accurate Accelerometer Test*Battery operation*All tests use 32-bit resolution A to D Converter*All data downloaded to PC via Ethernet link*Records all data to a flexible easy to use database*Records time and date of tests
-
product
RF & Microwave Test Cables
Rosenberger Hochfrequenztechnik GmbH & Co. KG
VNA Test Cables and microwave cable assemblies (RF Coax cable assemblies) must have a high degree of mechanical flexibility in combination with constant electrical stabilities. Such cables are usually used in laboratories for high-frequency measuring applications and test stations, as well as in the areas of telecommunications, automotive, medicine, industry, consumer electronics and aerospace for signal transmission and other applications.
-
product
Stability Testing Chambers
A stability testing chamber is a specialized enclosure used to control and maintain specific environmental conditions, primarily temperature and humidity, for extended periods. It's used to assess the stability and shelf life of products, materials, or substances by subjecting them to controlled environmental stress.
-
product
Laser Diode Burn-In Testing
Laser reliability testing consists of a series of tests that laser diodes can be put under in order to ensure their reliability for post-production use. There are different types of tests that can be carried out and there are multiple measurements that can be taken in order to evaluate the reliability of the device. One of these tests is laser diode burn-in.
-
product
Textile Test Equipment
AVENO textile testing equipment including fabric tester, yarn tester, fibre tester, related abrasion tester, color fastness tester, strength tester, flammability tester, snag tester, pilling tester, and more. Mainly used to check the quality of textile products.
-
product
Functional Test for Engineering Lab
Spectrum BT
Designed to meet the needs of product engineering labs, production lines, test development centers, and repair depots, the Spectrum BT is a configurable and scalable functional test system. This focused system solves typical functional test coverage challenges throughout the defense/aerospace product life cycle—and it’s upgradable as test requirements evolve.
-
