Optical Modulation
See Also: Modulation, Modulation Analysis, Modulation Analyzers, Modulation Meters, MER
-
Product
PXIe-5663E, 6.6 GHz PXI Vector Signal Analyzer
781259-01
Signal Module
6.6 GHz PXI Vector Signal Analyzer - The PXIe‑5663E offers wide instantaneous bandwidth and supports RF list mode, which increases multiband measurement speed with fast and deterministic changes in configuration. You can use a PXIe‑5663E as either a spectrum analyzer or vector signal analyzer, and you can use it with the Modulation Toolkit to analyze custom and standard modulation formats. The PXIe‑5663E can perform measurements for a broad range of communications standards such as GSM, EDGE, WCDMA, WiMAX, LTE, Bluetooth, WLAN, DVB‑C/H/T, ATSC, and MediaFLO. Because all measurements are software defined, you can reconfigure the measurements using standard-specific toolkits. With these toolkits, the PXIe‑5663E provides a low-cost solution to high-performance RF measurements.The PXIe-5663E comprises the following modules:• PXIe-5601 RF Signal Downconverter• PXIe-5622 IF Digitizer• PXIe-5652 RF Analog Signal GeneratorThere is no physical device named "PXIe-5663E".
-
Product
PXI/PXIe High Density Precision Resistor Module
42-297A-121
Precision Resistor Module
The 40-297A-121 (PXI) and the 42-297A-121 (PXIe) are 4-channel programmable resistors with a range of 1.5 Ω to 925 Ω. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
PXI/PXIe RF Matrix, 16x2, 300 MHz, 50 Ω SMB With Loop-thru
42-728A-001-L
Matrix Switch Module
The 40-728A-001-L (PXI) and 42-728A-001-L (PXIe) are 16x2 50 Ω RF matrices with SMB connectors and Y-axis loop-thru. The 4x-727A/728A/729A range are high density RF matrix modules suitable for switching up to 300 MHz in 50 Ω or 100 MHz in 75 Ω. They are available in 50 Ω or 75 Ω versions with SMB connectors or in 50 Ω versions with a multiway connector.
-
Product
PCI Resistor Card 2-Channel 2 Ohm To 131k Ohm
50-293-034
Programmable Resistor Module
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXI 8 Slot BRIC 88x8 2A 1-Pole Matrix
40-567-102
Matrix Switch Module
The 40-567 PXI Matrix BRIC provides a range of high density matrix modules able to switch up to 2 Amps or 100VDC/70VAC. The 40-567 BRIC modules are available in 2, 4 or 8-slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using high quality electromechanical relays for high switching confidence.
-
Product
PXI 8-slot BRIC Multiplexer, 12-Channel, 80-Pole (8 Sub-cards)
40-570A-116
Multiplexer Module
The 40-570A-116 is a 12-channel, 80-pole High-Density Multiplexer and is part of our BRIC family. The 40-570A range is designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing.
-
Product
96-Ch SPST 2A-250VAC 24VDC Switching
YAV90064
Switch Module
96 relays SPST, 2ASwitching 2A 250Vac. Up to 62.5VACAN Control (or Ethernet with Ethernet to CAN Gateway)Drivers dll & VIs available.
-
Product
PXI Fault Insertion Switch, 6-Channel, Two Fault Buses, 30 A
40-191B-012
Fault Insertion Unit
The 40-191B is a PXI fault insertion switch using solid state switching elements and is capable of carrying 40A on single channel or 30A on all channels at the same time and provides a robust solution to high current fault insertion.
-
Product
PXIe-4300, 16-Bit, 8-Channel, 250 kS/s, 300 V, Ch-Ch Isolated PXI Analog Input Module
781337-01
Analog Input Module
16-Bit, 8-Channel, 250 kS/s, 300 V, Ch-Ch Isolated PXI Analog Input Module—The PXIe‑4300 provides integrated data acquisition and signal conditioning for high-voltage measurements. It provides increased accuracy, simultaneous sampling, and synchronization features for scalable measurement systems. The PXIe‑4300 includes 300 Vrms channel‑to‑channel CAT II isolation and 3,300 Vrms channel‑to‑earth 5 second withstand isolation to protect users and equipment from hazardous voltages. This module offers programmable lowpass filtering, DC input coupling, and two PFI lines for digital input triggering. The included NI‑DAQmx driver simplifies hardware and configuration and measurement.
-
Product
PXI High Density Precision Resistor Module, 6-Channel, 3.5Ω to 1.51MΩ
40-298-044
Programmable Resistor Module
The 40-298-044 is a high density programmable resistor module with 6 channels which can be set between 3.5Ω and 1.51MΩ with 2Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXI 8-Slot BRIC Matrix, 110x16 1-Pole (10 sub-cards)
40-562B-121-110X16
Matrix Switch Module
The 40-562B-121-110X16 is a high density BRIC8 matrix module with a size of 110x16 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI Matrix Switch Module
Switch Module
PXI Matrix Switch Modules are organized into rows and columns and provide maximum flexibility for switching systems by allowing you to connect any channel to any other channel. PXI Matrix Switch Modules use a variety of relay types, including electromechanical armature relays, reed relays, field-effect transistor (FET) relays, and solid-state relays, each with their own benefits, allowing you to choose a matrix that fits your requirements. To program the switches, you can use the IVI-compliant NI-SWITCH driver software, complete with help documentation, example programs, and a soft front panel application for interactive control of switches. For intelligent management of complex switch systems, NI Switch Executive provides additional software tools to help you design, build, and deploy your switching system.
-
Product
PXI 5A MUX, 2-Bank, 24-Chan, Ind. Isolation
40-651-102
Multiplexer Module
This range of high density power multiplexer modules is suitable for switching inductive/capacitive loads up to 5A at 250VAC. It is available in the following 1-pole multiplexer formats: 1-bank 48-channel. 2-bank 24-channel. 4-bank 11-channel. 8-bank 5-channel. Connections are made via a front panel 50-way male D-type connector. Power multiplexer modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids.
-
Product
C Series Temperature Input Module
Module
The C Series Temperature Input Module features up to 16 channels of temperature input from either thermocouples or RTDS. This module can include anti-aliasing filters, open-thermocouple detection, and cold-junction compensation. Additionally, the module also feature isolation for safety, noise immunity, and high common-mode voltage range.The C Series Temperature Input Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
Product
8x4 Power Matrix, 2-Pole, 2xGMCT
40-550-902
Matrix Switch Module
This version of the 8x4 power matrix is for heavy current/low duty cycle power switching. Connections are made via a front panel 37-way D-Type male connector or two 20-way GMCT male connectors. Used for switching inductive/capacitive loads up to 5A at 250VAC. Power matrix modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids. Used for applications requiring switching of either mains voltage or direct current.
-
Product
PXI High-Density Matrix Module, 16x8, 1-Pole, 2 A 60 W, With Interlock
40-529B-001-HI
Matrix Switch Module
The 40-529B-001-HI is a 128 crosspoint PXI matrix with single pole switching and includes hardware intrlock. The matrix is configured as 16x8 using electro-mechanical relays with 2 A current handling.
-
Product
PXI/PXIe MEMS Optical MUX, 8-Channel, Single-Mode
40-852A-218
Multiplexer Module
The 40/42-852A-218 is a PXI/PXIe 8-channel multiplexer with SC/PC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
PXI Precision Resistor Module 18-Channel, 1 to 122
40-297-012
Programmable Resistor Module
This 18-channel PXI Precision Resistor Module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PXI/PXIe Microwave Multiplexer, Single SP4T, 6 GHz, 50 Ω, SMA, Remote Mount, Failsafe
42-784B-101-E
Multiplexer Module
The 40-784B-101-E (PXI) and 42-784B-101-E (PXIe) are single failsafe SP4T 6 GHz unterminated microwave multiplexers with remotely mounted relays. The 40/42-784B range is available with single, dual or triple, SP6T or SP4T multiplexers with front panel mounted or remotely mounted relays.
-
Product
LXI Microwave Multiplexer, SP4T, 8-Bank, 18GHz, 50Ω, SMA
60-803-108
Multiplexer Module
Our 60-803-108 is a 8 bank terminated SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 18GHz. The 60-803 range is capable of supporting up to 14 banks of terminated 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
PXI Precision Resistor Module, 9-Channel, 2 to 6.97k
40-297-030
Programmable Resistor Module
This 9-channel PXI Precision Resistor Module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PXI BRIC8 FIBO Matrix Dual 30x2 3pin brkout
40-595A-005
Matrix Switch Module
The 40-595A is a matrix module based on the BRIC format that is designed for fault insertion applications in safety critical testing. As with other BRIC modules the matrix size can be scaled to suit the user application. The 40-595 has a very high current rating of 10 Amps, ideal for higher power systems, and can be used as a conventional matrix.
-
Product
PXI 8-slot BRIC Matrix, 64x16, 1 pole (2 Sub-cards)
40-558-801-64x16
Matrix Switch Module
The 40-558-801-64x16 matrix is part of a range of BRIC ultra-high-density large PXI matrices are available in 2, 4, 8 or 12-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
Product
PXI 8 Slot BRIC 352x4 1-Pole (8 sub-cards)
40-562A-121-352X4
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI Single Microwave Transfer Switch 18GHz 50 SMA
40-782A-521
Switch Module
The 40-782A-521 is a single transfer switch and is part of our range of PXI microwave switching modules. It has a characteristic impedance of 50Ω and a maximum operating frequency of 18GHz. Connections are made via front panel mounted high quality SMA coaxial connectors.
-
Product
PXI Resistor Module 2-Channel 2R to 131k with SPDT
40-293-134
Programmable Resistor Module
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXI 8 Slot BRIC Matrix, 2A 1-Pole 256x12, 8 Sub-cards
40-597A-108
Matrix Switch Module
The 40-597A-108 is a PXI 1-pole 256x12 matrix in BRIC8 format and is part of a range of high density matrix modules able to switch up to 2 A or 200 VDC/210 VAC. The 40-597A BRIC modules are available in 2, 4 or 8-slot sizes to suit most high performance PXI matrix requirements, constructed using high quality electro-mechanical relays for high switching confidence.
-
Product
PXI 12-Slot BRIC Matrix, 10x32 1-Pole (2 sub-cards)
40-562B-321-10X32
Matrix Switch Module
The 40-562B-321-10X32 is a high density BRIC12 matrix module with a size of 10x32 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI 8 Slot BRIC 506x8 1-Pole Dual Analog Bus (11 sub-cards)
40-560A-121-506X8-M
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI/PXIe Microwave Multiplexer, Single SP6T, 26.5 GHz, 50 Ω, SMA, Remote Mount, Failsafe
42-784B-031-E
Multiplexer Module
The 40-784B-031-E (PXI) and 42-784B-031-E (PXIe) are single failsafe SP6T 26.5 GHz unterminated microwave multiplexers with remotely mounted relays. The 40/42-784B range is available with single, dual or triple, SP6T or SP4T multiplexers with front panel mounted or remotely mounted relays.
