Board Test Fixtures
jigs which hold, align and engage pcb with test interconnect.
See Also: Fixtures, Test Fixtures, Bare board Fixtures, PCB Test Fixtures, Genrad Fixtures
-
Product
Exchangeable Test Fixture
MA 2112/D/H/S-7
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 11,30 kg
-
Product
PCI Express A/D Board
AD8-1500 Series - Dual 8 bit, 1.5 GS/s
-
The AD8-1500 series has one or two 1500 MS/sec 8-bit ADCs, 8GB of on-board memory and the ability to transfer data directly into the host computer's memory at over 1 GB/sec. Streaming to the host computer can be performed simultaneously with acquisition to on-board memory, increasing the effective acquisition length by using the host computer's memory. Dual channel boards sample concurrently at twice the input clock frequency, and can also be software selected to run in single channel mode, providing twice the effective memory depth.
-
Product
Multiprotocol P104Plus Interface Board for Embedded Applications or Avionics Test & Simulation Applications
EXC-4000P104plus
-
The EXC-4000P104plus is a multiprotocol P104plus interface board for embedded applications or avionics test and simulation applications. Each board holds up to five independent modules. Two on-board modules use the MIL-STD-1553 communications protocol (M4K1553Px); another on-board module uses the ARINC-429 communications protocol; two additional detachable modules can be any one of the following types:M4K1553PxS (Single Function - RT validated) This module operates as a Bus Controller, Remote Terminal or a Bus Monitor. This module qualifies for airborne applications.M4K1553Px (Multi Function) This module operates as a Bus Controller, up to 32 Remote Terminals and as a Bus Monitor. Supports an Internal Concurrent Monitor in RT and BC/RT modes.M4K1553Px(S)-1760 Same as M4K1553Px(S) plus MIL-STD-1760 options.M4KMMSI Mini Munitions Store Interface module. Supports RT, BC/Concurrent-RT/Concurrent Monitor and Bus Monitor modes. Up to 8 hub ports EBR-1553 [10 Mbps 1553 protocol using RS-485 transceivers] and 1 monitor output.M4KH009 Based on our H009 family. This module operates as a Central Computer Complex (CCC) and/or up to 16 Peripheral Units (PUs) simultaneously, or as a Bus Monitor. In addition, a Concurrent Bus Monitor enables concurrent monitoring of the bus during CCC and PU simulation.M4K429RTx Based on our ARINC 429RxTx board. This module supports either five or ten ARINC 429 channels each of which can be configured in real time as a receive or transmit channel.M4K708 This module supports two channels of ARINC 708/453, each one selectable as either transmit or receive.M4KSerial This module supports up to 4 independent channels of serial communications, each of which can be selected as RS485, RS422 or RS232.M4KDiscrete This module supports 20 selectable input/open collector output discretes. The module supports TTL (0 to 5 volts) or avionics (0 to 32 volts) voltage levels.M4KCAN This module supports up to 6 independent channels of CAN 2.0B protocol with standard and extended message frames and message identifiers.
-
Product
ARINC-429 Module
M4K429RTx
-
The M4K429RTx is an ARINC-429 multi-channel test and simulation module to be used on the Excalibur 4000 family of carrier boards. The module supports up to ten ARINC-429 channels in any combination of transmitters and receivers. Each of these channels feature error injection and detection capabilities. The receive channels allow for the storage of all selected Labels with status and time tag information appended to each word.
-
Product
I/O Board
VME-6500 6U
-
The VME-6500 is a 6U VME Multifunction I/O board that can deliver in a single chassis slot the analog and digital I/O capabilities that could previously have occupied four slots, and can therefore make a significant contribution to substantially enhance performance and functional density. A high density and versatile design it provides 8 analog inputs and outputs as well as 16 digital inputs and outputs, all in a single 6U double Euro form factor.
-
Product
Bare Board Electrical Testing
ProbeMaster
-
ProbeMaster is the complete software solution to your shops needs in bare board electrical testing. ProbeMaster is PentaLogixs top-of-the-line software package that combines all of the power of the PentaLogix CAM and Fixturing packages with support for moving probe, Netlist Comparison and other robust features.
-
Product
DUT Prototype Board
DPB8800
-
The DPB8800 is an 11? x 14? PC board used to interface the tester with the Device Under Test (DUT). This board contains generous area for custom circuitry and extra relays. The DPB8800 is also available with standard solutions to test families of components like Op-Amps, Regulators, ADC?s and DAC?s. +/-15 V and +5 V are available to support circuitry biasing.
-
Product
Manual Fixture Kit
230354 – CMK-05
-
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
Product
PCI Digital I/O Boards
PISO-P16R16U
-
Universal PCI Board with 16-channel Isolated Digital Input and 16-channel Relay Output
-
Product
Cots Boards
-
Built in strict adherence to open architecture standards, Data Patterns designs COTS module products which are used in today's rugged applications and automatic test equipment platforms. Open standard form factors include cPCI, FMC & XMC, IP, MM, PCI, PCMCIA, PMC, VME, VPX and VXI.A portfolio of 'Off the Shelf ' products for testing and on-board applications have been developed by Data Patterns. COTS boards developed have been sold to many customers, in India as well as Europe and North America. They are used for system level products such as Automatic Test Equipment, Rugged Military Electronics, etc.Data Patterns focus on building COTS product is to provide the technological capability to develop system level products with very fast run around times. Use of Data Patterns' COTS module in system level products ensures Data Patterns ability to maintain the products for a significantly longer life cycle. The proximity to the system level engineering team with the COTS development team ensures that end applications are delivered faster, enabling a shorter time to market for the customers
-
Product
HES Prototyping Boards
-
HES™ is a feature-rich family of SoC/ASIC pre-silicon physical prototyping and hardware emulation boards. The family features boards with high-performance devices from either Xilinx (including Virtex-7, Virtex UltraScale, Virtex UltraScale+ and Zynq UltraScale+) or Microchip (PolarFire and SmartFusion2).
-
Product
PCI Daughter Boards
DB-24SSR/DIN (DB-24SSR with DIN-Rail Mounting)
-
The DB-24SSR/DB-24SSRDC includes 24 normally open, or form A, solid-state relays The board interface to filed logic signals, eliminating ground-loop problems and isolating the host computer from damaging voltages. The user can use the DB-24SSR/DB-24SSRDC to switch high voltage load, up to 240 VAC/50 VDC and up to 4 A. The relay is energized by applying a 5-voltage signal to the appropriate relay channel on the 50-pin header or 37-pin D-sub connector. Twenty-four enunciator LEDs, one for each relay, light when their associated relay is activated. Because there is a D-sub 37-pin connector on the board, the user may use it to interface to any TTL output board. In other words, the user may use it as a general purpose solid state relay output board.
-
Product
Turn-Key Functional / Mechanical Fixture
-
In addition to In-circuit testing, functional testing is widely used in the industry to verify electronic cards. This is why ReMaTek has always paid a special attention to the specific requirements of functional testing. Our dedicated engineering staff is prepared to handle all of your mechanical, electrical and software requirements. We are aiming particularly the small turn-key test systems where all the elements; the mechanical fixture, the test equipment and the test software, are put together in a complete system.
-
Product
ICT/FCT-Fixtures (Large IF)
GenRad CK-2-228X
-
The series of In-Circuit testers that are Teradyne for the 228x and TestStation are dedicated tools that rely on the tester hardware for diagnostics and test pattern delivery. The integration of the stand-alone BTS with the Teradyne ICT can enhance the system’s capability. In other words, it can provide access to additional tools. It provides the user with a common platform and portability of test patterns from stand-alone to ICT and later on to functional test and depot test stations.
-
Product
PCI Analog Output Boards
PISO-DA2U
-
Universal PCI, 2-Channel Isolated Analog Output Board. Includes two CA-PC09M D-Sub connectors
-
Product
ARM LPC2294 Based Board
MS 2500
-
- JTAG interface- Boot Flash interface- External Flash interface for data storage- External Bus interface- SPI Interface- I2C interface- Serial port interface- CAN Interface- LPC2694 based processor board- MIL1553B Bus Interface (Dual Redundancy)
-
Product
Bit Waveform Digitizer Board
ATS9373
-
ATS9373 is a 12 bit waveform digitizer board that can sample one analog input at rates up to 4 GS/s or two inputs at 2 GS/s. With on-FPGA FFT signal processing and data throughput as fast as 6.8 GB/s (6800 MB/s), ATS9373 is an ideal solution for many applications, including next generation OCT, radar, ultrasonics, spectrometry and RF signal recording.
-
Product
3-Axis Non-Robotic Automated Testing System
AT3
-
The Instron AT3 is a space-efficient, highly adaptable 3-axis mechanical testing platform designed for automated execution of tensile, compression, flexural, and lap shear tests. Built to comply with a broad spectrum of ASTM and ISO standards, it’s well-suited for evaluating materials such as plastics, elastomers, thin films, foils, and metals. The system streamlines the entire testing workflow from specimen measurement and handling to strain measurement and specimen disposal—enabling users to load up to 160 samples and let the AT3 take care of the rest. Boost productivity, reduce manual intervention, and achieve consistent, dependable results with every test cycle.
-
Product
AI Application Board
ASR-A501
-
Rockchip RK3588 Cortex®-A76 and A55 4'' SBC, ideal for AMR, AGV, robotic control, and AI surveillance applications. Based on Rockchip RK3588 Arm Quad Cortex-A76 2.4GHz and Quad Cortex-A55 1.8 GHz, and with build in 6 TOPS NPU. Dedicated MCU controller for CAN-FD guarantee CAN-FD performance.
-
Product
Relay Output Board
VME-2232A
-
VME-2232A is a 32-Channel Relay Output Board with Built-in-Test (BIT). Software compatible with the VMIVME-2232 and the VMIVME-2533.
-
Product
(ITA), Breakout Box & Fixtures
-
WinSoft provides a wide range of Interface Test Adapters (ITA) and test fixtures to meet the most challenging functional test and signal conditioning requirements. This includes high frequencies, voltages and current.
-
Product
Board Level Products
-
MicroImage Video Systems offers many of our products as board level allowing OEM’s (Original Equipment Manufacturers) to utilize MicroImage technology in their own products. While we offer many off the shelf products in board level, we can also offer customized versions with different connections and features in reasonable minimum quantities (starting as low as 25 pcs per order for some products). If you don’t see exactly what you are looking for, ask us, it may be something we have already designed or something we can change easily. Contact us today with your requirements.
-
Product
PCI Daughter Boards
DB-24RD/24/DIN (24V, D-Sub37 connector, DIN-Rail mount)
-
The DB-24R consists of 24 form C, electromechanical relays for efficient switching of load by programmed control. The contact of each relay can control a 0.5 A /110 V load or 1A / 24VDC. The relay is energized by applying a 5 voltage signal to the appropriate relay channel on the 50-pin Opto-22 compatible connector or D-Sub 37 connector . Twenty-four enunciator LEDs, one for each relay, light when their associated relay is activated . This board needs a +12VDC or +24VDC external power supply to avoid overloading your PC’s power supply.
-
Product
Meter Qualification Boards
WECO 8020, 8030
-
WECO Meter Qualification Boards by Radian Research enable extensive functional testing of single-phase and three-phase revenue grade electricity meters. Unlike Warm-up Boards and Load Boards that are limited to just powering the meter or applying a fixed current, WECO Meter Qualification Boards can test a variety of communications, disconnect and safety features. The WECO 8020 and 8030 have varying capabilities based on your requirements. They feature an innovative open socket design exclusive to RADIAN that ensures optimum operator safety. Capability, versatility and safety combine to make WECO Meter Qualification Boards THE logical choice.
-
-
Product
Incremental Length Gauges For Measuring Stations And Multi-gauging Fixtures
SPECTO series
-
*High system accuracy: ±1 µm*Very rugged design*Compact design for limited installation space*Various plunger actuation possibilities*Highly durable ball-bearing guide*Measuring range of up to 30 mm*Interfaces: 1 VPP, TTL*Protection rating of up to IP67
-
Product
ARM LPC3250 Board
MS 1509
-
- 32 Bit ARM LPC3250 Processor (256KB SRAM)- 133MHz External Bus Speed and 266 MHz internal CPU Speed- 32 Bit, 33MHz CPCI Bus, 6U Form Factor- External memory ( Flash – 2 MB, RAM - 512 KB, DPRAM – 128KB)- 10/100 MBPS Ethernet Interface- USB 2.0 Host/Device Interface- 2 RS232 Serial Ports, 4 RS422 Serial Ports- M Module Interface- 6U board compatible with CPCI & PXI backplanes- High Speed Logic Device- Hot Swap Feature- Front Panel and Rear IO Interface- External Bus through Rear IO- Reception of 3Kbytes within 2ms through Ethernet- Board Dimension is 160mm x 233.35mm- Power Requirements: +3.3V, +5V and +/-12V- Board Dimension is 160mm x 233.35mm- Board has Rear IO interface- Ethernet, JTAG, RS232, USB connectors at front side- BSPs and Driver software for Windows and Linux OS
-
Product
Board
ARDUINO UNO WiFi REV2
-
The Arduino UNO WiFi Rev.2 is the easiest point of entry to basic IoT with the standard form factor of the UNO family. Whether you are looking at building a sensor network connected to your office or home router, or if you want to create a Bluetooth® Low Energy device sending data to a cellphone, the Arduino UNO WiFi Rev.2 is your one-stop-solution for many of the basic IoT application scenarios.
-
Product
Noise Board
332D-11 VG
-
This printed circuit board was designed to original specifications and contains OEM specified parts. This board is required for testing the 332D-11 series gyros. Also contained on board is the Method A type calibration and sample and hold circuits required to perform the calibration of the noise circuits.
-
Product
Physical Testing Test
-
Physical Testing by Aero Nav: mechanical, weathering, environmental, immersion, electrical, luminance, thermal analysis, thermal conductivity, water exposure, saltwater exposure, etc.
