Showing results: 1456 - 1470 of 1529 items found.
-
1131 IN -
Standard Electric Works Co., Ltd
● Hight quality Taut Band movement.● Three insulation test voltages (DC) : 250V, 500V, 1000V.● Two ranges for continuity test : 2Ω & 20Ω.● Compact and lightweight.● AC voltmeter with linear scale up to 600Vac.● 200mA continuity short-circuit current.● 1mA test current on insulation test at nominal voltage.● Automatic discharge of capacitive and inductive circuit with charge stored in the circuit under test.● Live warning and display of external voltage presence.● Fuse, air gap, crowbar and overload protected.● On line battery monitoring shows if battery is ok.● Manual zero ohm adjustment.● Low battery consumption.● Mirror scale.● Push and turn locking switch for continuous and hand free testing.● BS 16 edition.
-
Dewesoft d.o.o.
Aerospace Testing SolutionsDewesoft offers a variety of solutions for aerospace testing. From standard data recording, structural dynamics, rotating machinery analysis, acoustic testing, to more specific applications like ground station telemetry solutions with full support for ARINC-429 and MIL-STD-1553 buses, PCM telemetry, IRIG 106 - Chapter 10, Ethernet packets, and iNet telemetry.We can provide flexible and robust data acquisition hardware and software that will match your requirement for testing airplanes, helicopters, rockets, satellites in the air, space, or on the ground - proving ground, wind tunnel, vibration shaker or acoustic chamber. Our solutions are being used and trusted by leading aerospace companies on the most demanding projects like NASA, ESA, Space X, Airbus, Boeing, Lockheed Martin, Bombardier, Honeywell to name just a few.
-
DVS Resolution -
Surface Measurement Systems
DVS Resolution’s key feature is the combined ability to precisely control and measure temperature and relative humidity while recording the highest resolution changes in mass. DVS Resolution uses a dry carrier gas typically nitrogen or compressed air for its operation. Digital mass flow controllers regulate flows of dry and saturated gases. Relative humidity is generated by precisely mixing dry and saturated gas flows in desired flow ratios which produce expected relative humidity. In a typical experiment a known concentration of water vapor is delivered over a sample placed inside the sample pan connected to the Surface Measurement Systems Ultrabalance™ measuring realtime mass changes caused by sorption or desorption of water molecules. Prior to sorption measurements, the sample can be in-situ preheated/dried at temperatures of up to 300oC.
-
Educated Design & Development, Inc.
1 or 3 actuating device(s) for rocker switches and push- button switches with 2 single-acting pneumatic cylinders each, with air throttle valves to adjust the actuating speed, height-adjustable mounted to holders, with multiple adjustable specimen holders, with safety sockets to connect the specimens to external test voltages and loads1 housing, made of steel, with protective hood1 plug-in unit with front panel for operating the devices.1 Control device for the entire unit:main switch with EMERGENCY OFF function, safety switch for the protective hood, mains cord and fuses1 control device for each actuating device:programmable control unit with exchangeable program modules (containing the "test rhythm") and for adjusting and indicating the test parameters "number of strokes" and "stroke time", start and stop push-buttons, push-buttons for moving manually the cylinder pistons and as actuation indicator for the cylinder
-
ACE Technology
1.The outer skin is make of steel plate coating with Zinc on double sides, processed with digital control, and painting process on surface for protection. 2.The inner material is stainless steel SUS304. 3.The chamber is divided into 3 parts: high temperature zone, low temperature zone and testing zone. Special heat isolating structure and preserve cold and heat treatment. 4.Lead high or low temperature into chamber by switching over cold or heat air valve. 5.Can set low, high, or thermal shock model independently, two cases or three cases option at thermal shock model, meanwhile, high and low temperature testing function is available. 6.Switching over time for wind direction valve is less than 10 seconds.
-
Teledyne Defense Electronics
Teledyne Advanced Electronic Solutions assembles and tests a variety of complex circuit card assemblies (CCAs) using leading edge, advanced technology assembly automation. We specialize in low-volume, high-mix assembly of highly complex CCAs.- RF, analog, high-speed and digital circuits on rigid-flex and Cu core substrates- Typical lot sizes from 3 to 300 pieces- 4 high speed, flexible SMT lines- Production processes for components from 0201 chips to large grid-array components and connectors- 100% solder paste, automated optical, and x-ray inspection- Forced air convection reflow with inert atmosphere option- Special processes for RF assemblies (filters, shields, etc)- BGA underfill, conformal coating, etc.- Selective and wave solder pin-thru-hole processes- CCA and component bonding processes
-
PCE Instruments
Explore PCE Instruments' absolute moisture meter offerings. Our absolute moisture meter products can measure relative air humidity, while our combination devices can also measure temperature. Each absolute moisture meter measures different ranges of humidity, depending on the model. Relative humidity is an important factor in everything from gardening to transport and industry.Our absolute moisture meter products are versatile, as they can take measurements, store the data to memory and transfer the data to a computer for detailed analysis. Different moisture probes that correspond to the materials to be measured can be connected to each absolute moisture meter. For most of the materials, you will find calibration curves within the internal memory of our absolute moisture meter products. You then only need to select the appropriate calibration curve for the material you wish to measure.
-
Model T703 -
Teledyne Advanced Pollution Instrumentation
The Model T703 is a microprocessor controlled ozone calibrator for precision gas analyzers. The Model T703 can deliver concentrations from 50 ppb to 5 ppm at flows from 1 LPM to 5 LPM.The Model T703 has two major components; the ozone generating device and the photometer. The ozone generator produces ozone by passing zero air over a UV lamp. Flow rate and lamp intensity are adjusted to deliver a specified ozone concentration by volume. The temperate and pressure compensated photometer, identical to that of the Model T400 ozone analyzer, provides feedback control of the UV lamp intensity, assuring stable ozone output. A nearly unlimited number of calibration sequences may be programmed into the non-volatile memory of the T703, covering time periods up to a year.
-
1132 IN -
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Three insulation test voltages(DC) : 250V, 500V, 1000V.● Two continuity test on low ohms : 3Ω & 500Ω.● Compact and lightweight.● AC voltmeter with linear scale up to 600 Vac.● 200mA continuity short circuit current.● 1mA test current on insulation test at nominal voltage.● Automatic discharge of capacitive and inductive circuit with charge stored in the circuit under test.● Live warning and display or external voltage presence.● Fuse, air gap, crowbar and overload protected.● On line battery monitoring shows if battery is ok.● Manual zero ohm adjustment.● Low battery consumption.● Mirror scale.● Push and turn locking switch for continuous and hand free testing.● BS 16 edition.
-
8052 IN -
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Three insulation test voltages(DC) : 250V, 500V, 1000V.● Two continuity test on “low ohms” : 3Ω & 500Ω.● AC voltmeter with linear scale up to 600 Vac.● 200mA short circuit current for continuity.● 1mA test current on insulation test at nominal voltage.● Automatic discharge of capacitive and inductive circuit with charge stored in the circuit under test.● Live warning and display of external voltage presence.● Fuse, air gap, crowbar and overload protected.● On line battery monitoring shows if battery is ok.● Manual zero ohm adjustment.● Low battery consumption.● Mirror scale.● Push and turn locking switch for continuous and hand free testing.● Supplied with high quality test leads.
-
1652 IN -
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Three insulation test voltages(DC) : 250V, 500V, 1000V.● Two continuity test on “low ohms” : 3Ω & 500Ω.● AC voltmeter with linear scale up to 600 Vac.● 200mA short circuit current for continuity.● 1mA test current on insulation test at nominal voltage.● Automatic discharge of capacitive and inductive circuit with charge stored in the circuit under test.● Live warning and display of external voltage presence.● Fuse, air gap, crowbar and overload protected.● On line battery monitoring shows if battery is ok.● Manual zero ohm adjustment.● Low battery consumption.● Mirror scale.● Push and turn locking switch for continuous and hand free testing.● Supplied with high quality test leads.● BS 16 edition.
-
8031 IN -
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Three insulation test voltages(DC) : 250V, 500V, 1000V.● Two continuity test on “low ohms” : 2Ω & 20Ω.● AC voltmeter with linear scale up to 600 Vac.● 200mA short circuit current for continuity.● 1mA test current on insulation test at nominal voltage.● Automatic discharge of capacitive and inductive circuit with charge stored in the circuit under test.● Live warning and display of external voltage presence.● Fuse, air gap, crowbar and overload protected.● On line battery monitoring shows if battery is ok.● Manual zero ohm adjustment.● Low battery consumption.● Mirror scale.● Push and turn locking switch for continuous and hand free testing.● Supplied with high quality test leads.● BS 16 edition.
-
NIU3E -
North Atlantic Industries
The NIU3E is a small, rugged, low-power, self-contained multifunction I/O processing system preconfigured with 24-CH programmable Discrete I/O, 8-CH ARINC 429/575, 4-CH CANBus and 2-CH MIL-STD-1553 functions and incorporates an Ethernet switch module that offers four (4) 10GBase-SR multimode fiber optic ports and sixteen (16) 10/100/1000Base-T Ethernet ports. The NIU3E can also be configured with one smart Configurable Open Systems Architecture™ (COSA®) function module. The NIU3E boasts a Dual or Quad Core ARM A53 processor for customer application and I/O and communications management. The NIU3E is configured with two 10/100/1000Base-T (GbE) Ethernet ports and an RS-232 port for maintenance / diagnostic or configuration interface. Ideally suited for rugged Mil-Aero applications, the NIU3E delivers off-the-shelf solutions that accelerate deployment of SWaP-optimized systems in air, land and sea applications.
-
NOVOTEST TP-1 -
NovoTest
Portable Coating Thickness Gauge NOVOTEST TP-1 – device for operative non-destructive testing of coating thickness in compliance with ISO 2808 with high measurement accuracy.Coating thickness gauge is designed to test:thickness of various thick protective coatings on various metals and alloys;thickness of paint and other dielectrics – radioabsorbing, mastic, teflon, plastic, electroplating coatings on steel;thickness of electroplating and paint coatings on non-ferromagnetic alloys and non-ferrous metals;thickness of bitumen and other thick coatings on various metals and alloys;as well as relative humidity, air temperature, surface temperature, dew point temperature and difference between surface and dew point temperatures, estimate the depth of grooves and the surface roughnessElectronic thickness gauge – device which widely used in shipbuilding and automotive industries for measuring of the thickness of paint, in order to test the quality of products, also it used for determining technical condition of the tested objects.
-
National Technical Systems
Gravelometer testing is designed to evaluate the resistance of vehicle surface coatings (paint, clear coats, metallic plating, etc.) to chipping caused by the impacts of gravel and other flying objects in accordance with SAE and ASTM standards. The primary usage of this test is to simulate the effects of the impact of gravel or other debris on automotive parts. Test samples are typically mounted in the back of the Gravelometer, and air pressure is used to project 1 pint (approximately 300 pieces) of gravel at the sample. The test sample is then removed and gently wiped off with a clean cloth. Tape is then applied to the entire tested surface. Removal of the tape then pulls off any loose fragments of the coating. The appearance of the tested sample is then compared to standard transparencies supplied by SAE to determine the chipping ratings. Visual examination can also be used to describe where in the coating/substrate system that the failure has been induced.
