Synchronous Ethernet
ITU-T standard governing timing node to node through the physcial layer interface.
-
Product
Automotive Ethernet Tools
-
Automotive Ethernet (AE) represents the latest challenge to the status quo in automotive networking. Many OEMs are now moving forward with this exciting new technology, which promises high performance at low cost, especially for infotainment applications. Capturing Automotive Ethernet Frames. Automotive Ethernet traffic cannot be monitored using the same techniques employed for buses like CAN. Ethernet networks use star topology, so there is no single point to monitor an entire network. The sophisticated technology employed also means bit values cannot be interpreted directly from voltage levels. Finally, Ethernet hardware silently discards erroneous frames, making diagnosing problem conditions difficult. Intrepid’s tools are designed to address all of these issues conveniently and efficiently.
-
Product
Network Synchronization Device
VCH-003
-
The Network Synchronization Device (NCD) VCH-003 is intended for use on the Unified Telecommunication Network of the Russian Federation. Depending on the configuration of the NSS, VCH-003 can be used to generate and multiply synchronization signals of 2048 kHz and 2048 kbps as part of the PEG, as an OIG to restore synchronization signals received from the line at the transit node.
-
Product
Industrial Ethernet Network
CC Link IE Field
-
CC-Link IE Field network is the first gigabit industrial Ethernet network extended down to the field device level. It combines the best of existing technologies and applies them in a highly reliable architecture that provides exceptional data bandwidth and transaction rates. The new network uses commercially available Cat5E cable and RJ45 connectors.
-
Product
Industrial Ethernet Switch
-
C1D2 industrial Ethernet switches are energy-efficient, durable, and robust. Our switches are suitable for use in mission-critical environments.
-
Product
20-port Ethernet Switch
VPX3-652
-
Curtiss-Wright Defense Solutions
The VPX3-652 is a fully featured Layer-2 managed Ethernet switch designed to support advanced network architectures for the defense industry.
-
Product
Ethernet Digital Interfaces
Model 8063
-
All of ICS's Ethernet Digital Interfaces are user configurable and let you transfer data as bits, bytes, as strings of bytes or transparently. All data lines are high power TTL outputs or floating inputs with pullup resistors for sensing CMOS signals or switch contacts. All interfaces conform to the IEEE-488.2 Standard, are VXI-11 compatible and/or support TCPIP Raw Socket protocol.
-
Product
Ethernet Switches
-
Choose Omega's industrial-grade Ethernet switches to facilitate reliable data transmission speeds. These switches can withstand extreme conditions.
-
Product
10G Ethernet Emulator
VirtualNetTM XG
-
VirtualNet-10G is a high-performance Network Emulator that replicates real world Ethernet network effects such as latency and errors on user traffic in a controlled environment. The VirtualNet-10G emulator uses customized ICs to support full line rate performance at all frame sizes and impairment settings. The emulator can be transparently installed in-line as shown in the diagram below. VirtualNet-10G emulator has an intuitive and easy to use GUI interface and a very powerful TCL based CLI to aid in configuration and testing.
-
Product
IMS - Modular Synchronization
-
Meinberg Funkuhren GmbH & Co. KG
The IMS series (Intelligent Modular Synchronization) from Meinberg offers redundancy for synchronization sources and power supply in combination with a highly modular slot-based housing, which also supports hot swapping and scaling options in the field.
-
Product
Ethernet
-
The M4K-ETH is an intelligent Gigabit Ethernet interface module for the multiprotocol Excalibur 4000 family of carrier boards (only 64 bit versions). The module supports 10Mhz, 100Mhz and 1Ghz Full Duplex UDP/IP Ethernet.The receive channels allow for the storage of all packets to all MAC and IP addresses with status and Time Tag information appended to each packet. The receivers allow for filtering based on MAC address, IP address and UDP port. The transmit channels enable the user to define a Bus list which controls timing and order of packets without host intervention or immediate mode which enables the host to transmit packets at will.
-
Product
Bit Synchronizer Daughterboard Rates up to 25 Mbps
LS-40-DB
-
The Lumistar LS-40-DB Bit Synchronizer Daughterboard provides optimal reconstruction of a serial PCM data stream that has been corrupted by noise, phase jitter, amplitude modulation, or base line variations. The all-digital design assures a high performance, consistent product, with excellent reliability and long-term stability.
-
Product
SDH Ethernet Testers
-
Wuhan Sunma Technology Co., Ltd.
The SunmaFiber SDH & Ethernet is easy to use, cost effective Ethernet testing solution for basic physical layer cable testing, layer 2 and layer 3 traffic generation, and full RFC 2544 testing. The rugged, battery operated, application specific test tool enables field technicians to turn-up Ethernet and IP services by running an RFC 2544 test or following a set of methods and procedures. The product has been designed for front-line technicians who do not have experience dealing with emerging Metro Ethernet technologies and need a simple to use solution for Ethernet and IP testing.
-
Product
Multi-Channel Synchronization Module for M8195A
M8197A
-
Synchronization Module for up to 4x M8195A Arbitrary Waveform Generator units.
-
Product
8FE+2FE SC Single-Mode Managed Ethernet Switch, -40~75℃
EKI-7559SI
-
2 x SC-type fiber ports, plus 8 Fast Ethernet portsRedundancy: X-Ring (high-speed recovery time<10ms), RSTP/STP (802.1w/1D)Management: Web, Telnet, Serial Console, SNMPControl: VLAN/GVRP, QoS, IGMP Snooping/Query, LACP, Rate LimitSecurity: IP/MAC and port binding, DHCP Server, IP access list, 802.1X, SNMPv3Diagnostic: Port Statistic, Port Mirroring, RMON, Trap, Email Alert, SyslogDual 12 ~ 48 VDC power input and 1 Relay OutputRobust mechanism and special heat spreader designSupports wide operating temperature -40 ~ 75° C
-
Product
Ethernet Communications
-
Campbell Scientific offers complete Ethernet connectivity solutions for our data acquisition needs. Data loggers are available with integrated Ethernet, as well as stand-alone Ethernet modules.
-
Product
Ethernet Media Converter
-
A physical layer equipment which interconnects the Ethernet, Fast Ethernet, or Gigabit Ethernet on copper UTP and the related fiber optics network. Ethernet media converter meets corresponding IEEE 802.3 standards.
-
Product
Point on Wave Synchronous Test Sequencer
-
The Portable Point on Wave Synchronous Test Sequencer is India’s only system that helps in time synchronizing the control signals during short circuit tests performed on medium and high voltage switchgear and control gear.
-
Product
Ethernet Interfaces
-
All of ICS's Ethernet Interfaces conform to the IEEE-488.2 Standard and are fully VXI-11 compatible. Use with any Etherrnet based test system. Complies with LXI VXI Discovery method.
-
Product
EN50155 Managed PoE Ethernet Switch
EKI-9512E-4GMPW
-
8 x M12 D-Coded 10/100 Mbps PoE ports + 4 x M12 X-Coded 10/100/1000 Mbps Byapss ports, Complies with EN50155 & EN50121-3-2. Operating temperature: -40 ~ 75°C, Operating power input range: 16.8~137.5VDC, Supports X-Ring Pro for rapid and predictable convergence.
-
Product
Interface Board for Gigabit Ethernet
40-965-910
-
The 40-965-910 is a converter card for the 40-201 Ethernet/AFDX Fault Insertion Switch. Adapts the 78-Pin D-type connector on the front of the module to 4 RJ45 sockets and one 9-way D-type connector for fault signals. Allows the fault insertion testing of Gigabit Ethernet signals.
-
Product
Ethernet I/O Products
-
Our products are designed to cover the most common industry applications. Our full selection of analog, digital, and serial I/O products with Ethernet connectivity allows for easy, simple to use data acquisition and control. Configure an IP-address and quickly acquire and output data over your network.
-
Product
Airborne Receivers & Bit Synchronizers
-
The Lumistar LS-28-DRSM Series Multi-Mode Multi-Band Receiver/Combiner/TM Processing Unit is designed using ruggedized packaging to survive severe airborne conditions. The LS-28-DRSM is available in several configurations: 1) Airborne receiver only (RF to bits), 2) Airborne bit synchronizer only, 3) RF to TM Processing and Display (RF to bits to UDP decom to LAN Client Displays). Models with receivers are available in any band form 200 MHz to 7 GHz with S, lower L and C bands as standards. Other RF bands are available, please consult the factory for details. This unit can be mated with other Lumistar products to provide a complete air-to-ground re-transmission system.
-
Product
Ethernet Parallel Interface
Model 8113
-
* Provides 12 8CMOSL I/O lines for 3.3 and 5 volt logic.* 10/100 MHz Ethernet Interface with Auto-MDIX capability* Robust hardwired TCP/IP (Raw Socket) communication port prevents flooding, spoofing and injection attacks.* Included RS-232 serial control port for older systems.* Optional I2C port for connection to touchscreen panel or other I2C devices.* Standard board has a horizontal Ethernet connector and 150-pin Digital IO connector on the component side.
-
Product
Managed Ethernet Switches
-
CommFront offers a range of rugged, industrial-grade, managed and unmanaged Ethernet Switches. These Industrial Ethernet Switches have been designed for harsh industrial environments and withstand a wide temperature of -40°F to 185°F (-40°C to 85°C), and they come with the options of 10/100/1000M for both Fast and Gigabit Ethernet networks. In addition, our advanced, rugged, industrial-grade, Fast and Gigabit Ethernet Switches support both point-to-point and multi-drop (daisy-chain or self-healing redundant ring) fiber optic networks, which are designed to cover large areas. These industrial Ethernet Switches support up to 255 fiber nodes, and each fiber node can extend the Fast and Gigabit Ethernet data up to 100 miles or 160 km. When configured as a ring network, the built-in self-healing feature allows the Ethernet data to be transmitted clockwise or counterclockwise; therefore, failure of any individual converter will not affect other devices located on the same ring, making the entire Ethernet network more robust and reliable.
-
Product
EN50155 Ethernet Switches
EKI-9508 series
-
EKI-9508 series switches, built for railway applications, feature rugged IP67 design, M12 connectors, PoE options, and comply with EN50155 & IEC61373.
-
Product
Unmanaged Ethernet Switch
EKI-2712X-SPE
-
Provides 2 x 10G, 2 x 2.5G, 2 x SFP+, and 6 x SPE ports, SFP+ socket for easy flexible fiber expansion, Offers DIN Rail and wall mounting options. Supports wide-range 9–36VDC power input, Compliant with IEEE 1588 E2E TC standard, Supports gPTP IEEE 802.1AS-2020 Time-aware bridging.
-
Product
Encoders For Synchronous Motors
-
Precise optical scanning - for optimum signal and control quality in your application. Compact designs from 36 mm enable space-saving installation. Open real-time digital protocol.
-
Product
Ethernet Switch
SWI-22-10
-
Curtiss-Wright Defense Solutions
The Parvus SWI-22-10 is a rugged Commercial Off the Shelf (COTS) Gigabit Ethernet switch card optimized for size, weight and power (SWaP) sensitive embedded military and civilian computer network systems applications.
-
Product
Ethernet MACsec PHY
-
Macom Technology Solutions Holdings Inc.
IEEE 802.1AE Media Access Control Security (MACsec) is an industry standard security technology that provides secure communication for Ethernet traffic. MACOM’s wire-speed Ethernet MACsec PHY products offer highly scalable and cost-effective encryption solutions to address the data security issues in wireless, carrier, data center and cloud networks. Combining MACOM’s strength in high speed, high performance mixed-signal I/O and industry leading CMOS silicon technology, MACOM’s MACsec PHY products provide line-rate encryption and authentication at a very low power-footprint that enables encryption at wire-speed on every port. They are ideal for adoption on switch/router line cards, data center interconnect (DCI) transponder and wireless xHaul aggregation systems to provide security function in addition to the connectivity to optical and copper modules.
-
Product
Ethernet Connector Modules
-
With an extensive line of high-quality ethernet connector modules in our product lineup, Pulse Electronics Networking BU can easily supply the parts you need to develop your next ethernet product.
