Signal Sources
Instrument that provides a stimulus signal (waveform). (www.tek.com)
See Also: Signal, Signal Processing, Signal Integrity, Signal Proccessing, Signal Analyzers, Signaling, Signal Conditioning, Signal Generators, Signal Meters, Signal Conditioners
-
Product
Isolated Voltage Source
SIM928
-
Stanford Research Systems, Inc.
The SIM928 Isolated Voltage Source is ideal for applications where ultra-clean DC voltage is required. Voltage can be set between ±20 VDC with millivolt resolution, and the source can drive up to ±10 mA
-
Product
Power Meter & Light Source
-
Used to test fiber optic cables for signal strength and attenuation loss.
-
Product
12DO(Source Type) Modbus RS-485 Remote I/O
ADAM-4056SO
Remote Interface Unit
12ch source type digital outputProtocols:Modbus RTU,ASCIIWatchdog timer to recover the system5000VDC isolation protection
-
Product
"Signal Transporter"
LTX-5510
-
The LTX-5510 enables precise conveyance of analogue plus four channels of digital information over fibre optic links ranging from meters to more than 10 kilometers. Incoming analogue data is digitised to 12-bit precision at 50 mega-samples per second and transmitted over optical fibre at a 1 Gb/s data rate.?
-
Product
Calibration Light Sources
-
Calibration light sources have well-known, well-defined spectral outputs (e.g. with a sharp, known peak at a specified wavelength) and are used to calibrate light measurement systems, such as spectrometers.
-
Product
PCB S.I/P.I (Signal Integrity/ Power Integrity)
-
Why need for PCB Simulators?Higher data speed (>GHz) Higher density Larger system size EMI concern Cost cut down Reduce of project term
-
Product
Frequency Converter Characterization With Wideband Modulated Signal
N5245BQ
Network Analyzer
The N5245BQ provides the N5245B 50 GHz PNA-X network analyzer, application software and accessories for frequency converter measurements with modulated signal such as EVM, NPR and ACPR in addition to gain, gain compression, IMD and other measurements
-
Product
Charge Amplifiers & Signal Conditioning
-
The use of charge amplifiers alongside piezoelectric charge output sensors is still widespread in many industries. This is due to the rugged and high temperature capabilities of the sensors. There are many challenges in using these sensors and it needs a good understanding of the technology to get a quality, noise free signal for accurate data.
-
Product
RTM Analog & Discrete Signal Conditioning Board
-
CPCI Rear IO Analog and Discrete Signal Conditioning Board is a signal conditioning and interface board for CPCI based Advance Compute & IO Module (MS3663i). This board primarily focusing on signal conditioning of TTL/CMOS DIO levels to required type of discrete input and output interface. Digital IO from ACIO board to discrete IO at Rear IO interface. Board takes 144 DIO from ACIO and does Open/Ground, 28V/Open, 28V/Ground configuration. In addition it shall generate additional 32 discrete input / output signals with signal conditioning and all IO interfaces are brought to two 96 Pin Euro Connector. And Board takes 16 Analog outputs and 64 Analog inputs from ACIO and does signal conditioning. In addition it shall generate additional 40 Analog input and 32 Analog output signals with signal conditioning and all IO interfaces are brought to two 96 Pin Euro Connector
-
Product
LVDS (Low Voltage Differential Signaling) Drivers and Receivers
-
LVDS (Low Voltage Differential Signaling) Drivers and Receivers from Analog Devices offers designers robust, high speed signaling for single-ended to differential solutions for point-to-point applications. Our selection of products conform to the TIA/EIA-644 LVDS standard and contain the first LVDS transceivers to meet 8 kV IEC ESD performance standards - important for robust, interboard applications where the connectors can be exposed to more harsh electrostatic environments. Companion differential line receivers and differential line drivers support up to 600Mbps. LVDS greatly improves noise immunity and minimizes emissions for high speed point-to-point data transmission and is a low power alternative to emitter-coupled logic (ECL) or positive emitter-coupled logic (PECL) signaling.
-
Product
Precision Multi-Channel DC Source PXI Card
GX1838 Series
PXI Card
The GX1838 is a multi-channel programmable DC Source providing multiple discrete outputs for avionics automotive, industrial testing and other ATE applications.
-
Product
GPIB Controlled Signal Routing Box
GPIB
-
Test Electronics will customize the TE3000 GPIB signal routing box for your test application. Then, you simply rack and stack all the equipment, cable all the switched signals to the back of this GPIB box, add a rack mount computer, plug in the National Instruments GPIB board and software. Then run your customized GPIB based test system.
-
Product
EXG Signal Generators
-
The cost-effective EXG X-Series signal generators address critical speed and uptime needs for manufacturing test. With analog and vector models, the EXG provides the signals you will need for basic parametric testing of components and functional verification of receivers.
-
Product
RTM Analog Signal Conditioning Board
MS 3633I
-
CPCI Rear IO Analog Signal Conditioning Board is a signal conditioning and interface board for CPCI based Advanced Compute & IO Module (MS3639i). This board primarily focusing on all type of Analog input and output interface including signal conditioning from ACIO board to Rear IO interface. Board takes 16 Analog outputs and 64 Analog inputs from ACIO and does signal conditioning. In addition it shall generate additional 40 Analog input and 32 Analog output signals with signal conditioning and all IO interfaces are brought to two 96 Pin Euro Connector.
-
Product
Car-to-X Signal Strength Emulator
-
Qosmotec Software Solutions GmbH
QPER-C2X is a special adaptation of the signal strength emulator QPER, designed for mobile and Vehicular Ad-hoc Networks (MANet and VANet). Every radio devices in such an infrastructure-less network acts as a sender, receiver, and forwarder (router). Therefore, the ports of the QPER-C2X hardware are fully connected with each other by dynamically controllable attenuators. The system is fully designed for frequencies up to 6 GHz, since wireless communication for Intelligent Transport Systems (ITS) is based on the WLAN standard IEE 802.11p from 5.850 MHz to 5.925 MHz. The connected ITS stations can be either on-board units, as they are built into cars, or road side units that are used by road infrastructure (traffic lights, road work area delimiters, velocity signs). For tests in the lab, radio modules of such ITS stations are each kept in a shielding box that prevents any unwanted radiation over the air.
-
Product
Customizable EFP/ENG Signal Transport
BullDog Mini Series
-
An Ideal Solution For Small Remote Broadcast Productions The BullDog Mini is a compact, rugged field fiber transport device designed from the ground up to meet the needs of single camera and booth kit setups. The BullDog Mini can transport bidirectional 3G-SDI, IFB, and two MIC/line audios as well as, two serial data channels – all over a single strand of single-mode fiber. Optical connector options include SMPTE, opticalCon, or standard ST. With options for remote power via SMPTE hybrid fiber cable and battery operation, the BullDog Mini is ready for any location regardless of available power.
-
Product
SNS Series Noise Source 10 MHz to 26.5 GHz (ENR 15 dB)
N4002A
Noise Source
The SNS series N4002A noise source was designed to measure DUT noise figures reliably and accurately up to 30 dB from 10 MHz to 26.5 GHz.
-
Product
Multi-channel GPS Signal Simulator
MP6220
-
*Up to 8 channels support positioning test*Can also be used as a single channel
-
Product
AC Source
AMF
-
The Intepro AMF Series is a complete line of single and three phase, 400Hz AC Frequency Converter products. With Power levels ranging from 6kVA up to 300kVA, the AMF series of frequency converter products are the ideal and cost effective solutions for precise frequency conversion in all avionics and higher frequency electronic applications. Power and frequency conversion is supplied by state-of-the-art IGBT pulse-width-modulated power amplifiers resulting in highly efficient power conversion, compact design and maximized performance with minimum downtime.
-
Product
Laser Source
TW3104
-
Techwin(China) Industry Co., Ltd
Laser Source TW3104 is an essential instrument for optical network installation, trouble shooting and maintenance which can be used with an optical power meter for measuring optical loss in single-mode or multi-mode fiber cables. TW3104 is the earliest light source model in Techwin. It features compact size, high output power, stable output power and excellent wavelength stability .
-
Product
Power Source
SP560
-
Clary's SP 560 is a 400W/560VA power source built for electronics equipment in IT, traffic and security applications, delivering constant, conditioned, regenerated AC power. It protects equipment from being disrupted, degraded or damaged due to harmful power events. Clary power conditioning completely isolates the cabinet from utility power enabling error-free operation during surges, sags, spikes, and other power anomalies. With an optional battery pack, the SP560 system operates as an On-Line, Double-Conversion UPS, extending the reliability of the cabinet's electronics during utility power failures (black-outs).
-
Product
Controllable, Programmable Linear DC Source
LAB / S
-
*Linear laboratory power supply*High quality DC sources with the lowest residual ripple*CV / CC mode with LED display*Protection against short circuit, overload and overtemperature*Optional IEEE 488, RS232, analog interfaces*3-phase input optional
-
Product
VCSEL Light Source
-
ams supplies LiDAR systems with specific light sources, called VCSEL (Vertical Cavity Surface Emitting Laser). These VCSELs offer specific advantages over other types of light sources as for instance Edge Emitter Lasers:
-
Product
Long Life Seismic Energy Source
1500LL
-
Excellent low frequency content. Using heavy-duty cluster spreader bars cluster elements in excess of 1,000 cubic inches possible without sacrificing peak output
-
Product
Controllable, Programmable Linear DC Source With Load
LAB / SLR
-
*Linear laboratory power supply*Integrated electronic load*Automatic range selection*Linear regulated DC source with automatic range selection*Built-in electronic load*Short-term peak load operation 240 or 480 watts*Protection against short circuit, overload and overtemperature*Double current / double voltage through "autoranging"*Fast control times approx. 250µ
-
Product
RF Signal Testers
-
RF Signal Generators, Record & Playback Systems, Players, Productivity Tools and More
-
Product
FaithTech Programmable DC Source FTP1000 Series
FTP1000 Series
-
Shenzhen FaithTech Technology Co., Ltd.
The FTP1000 series is a small volume, high performance and high power density programmable DC source.The 1U/19 "full width \ half width design makes the single device more lightweight and the cabinet integration more convenient.The maximum output power 1800W,it can be applied in different fields such as laboratory testing, system integration, and large-scale production line testing.
-
Product
SD-SDI Test Signal Generator
7750TG
-
The 7750TG Test Signal Generator provides a cost effective method of generating SDTV 270Mb/s test signals. The 7750TG is ideal for checking signal path integrity, monitor alignment or to determine system performance over varying cable lengths. The 7750TG generates test signals in 525 line and 625 line SMPTE 259M-C video formats and offers four 270Mb/s outputs.
-
Product
Programmable AC Power Source
LMX Series
-
The LMX Series encompasses an all new collection of High Performance 1 phase and 3 phase Linear AC Power Sources. All standard models operate from 15 to 5,000 Hz, range in power from 500VA to 30kVA, and provide nominal output voltage ranges up to 600Vrms L-N.
-
Product
Pulsed Source Measure Unit
-
The SpikeSafe SMU is a precision pulsed source measure unit that precisely sources pulsed current and simultaneously digitizes voltage. Optimized for precise and repeatable high-power LED and laser testing, SpikeSafe™ SMU (Source Measure Unit) current sources deliver precise pulsing with low microsecond rise times, low-jitter triggering and integrated digitizer for more accurate and repeatable high-power LED and laser testing.
