Digital to Analog Converters
Transform digital signals to analog.
-
-
Product
USB Converters and Hubs
-
The C1/D2 USB converters and hubs offer industrial features like high retention USB ports, DIN rail mounting, isolation, and wide temperature ranges.
-
-
Product
Wideband RF Up Converter
150
-
The Wavefront family is built around a wideband quadrature modulator and broadband frequency synthesizer. The quadrature modulator features an extremely wide modulation bandwidth and operates over a very wide carrier frequency range. The on-board synthesizer features low phase noise and software controlled tuning across the full frequency range.
-
Product
PCIe Digital Waveform Acquisition with Programmable Threshold - 250 MBit/s Internal Sampling Rate Timing, 250 MBit/S External State Clock
M4I.7720-X8
Digital Waveform
The M4i.77xx-x8 series digital waveform acquisition (logic-analyzer) cards include versions with 32 synchronous channels, either single-ended with programmable threshold levels or differential. The large onboard memory can be segmented to record different waveform sequences. While the M4i.77xx cards have been designed using the latest technology they are still software compatible with the drivers from earlier Spectrum digital acquisition cards. Therefore existing customers can use the same software they developed for a 10 year old 60 MS/s digital input card also for an M4i.77xx series 720 MS/s logic analyzer.
-
Product
PXI-6521, 16-Channel, ±30 VDC, 8 Sink/Source Inputs, 8 Relay Outputs, Isolated PXI Digital I/O Module
779313-01
Digital I/O
16-Channel, ±30 VDC, 8 Sink/Source Inputs, 8 Relay Outputs, Isolated PXI Digital I/O Module—The PXI‑6521 is an industrial digital I/O module with high channel isolation and industry-standard 24 V logic levels. For added safety, the PXI‑6521 requires a keyed connector. If a computer or application fault occurs, the PXI‑6521 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. It also features programmable power-up states, digital filtering, and change detection for optimal control over your application.
-
-
Product
PXIe 8 Bit High Speed DIgitizer - 1.25 GS/s on 2 Channels, 500 MHz Bandwidth
M4X.2211-X4
Digitizer
The 9 models of the M4x.22xx-x4 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
Product
Digitizer Adapter Module For FlexRIO
Digitizer
Digitizer Adapter Modules for FlexRIO can be used with a PXI FPGA Module for FlexRIO or the Controller for FlexRIO to create a high‐performance instrument with customizable firmware. With sampling rates from 40 MS/s to 3 GS/s and up to 32 channels, these modules cover a wide range of requirements for both time- and frequency‐domain applications. Digitizer adapter modules also provide digital I/O capability for interfacing with external hardware.
-
Product
PCI-7813, 3M Gate Virtex-II FPGA, Digital Reconfigurable I/O Device
779370-01
Digital I/O
The PCI‑7813 is a reconfigurable I/O (RIO) device that features a user-programmable FPGA for onboard processing and flexible I/O operation. With LabVIEW FPGA, you can individually configure the digital lines as inputs, outputs, counter/timers, PWM, encoder inputs, or specialized communication protocols. You can also program custom onboard decision making that executes with hardware-timed speed and reliability. The PCI‑7813 is well-suited for a wide variety of applications, such as high-speed waveform generation, sensor simulation, hardware-in‑the‑loop (HIL) test, custom communications protocols, bit error rate test, and other applications that require precise timing and control.
-
Product
RS-232 to RS-422/RS-485 Converter
ND-6520
-
ADLINK's NuDAM data acquisition modules make up a total acquisition network and control system. Up to 256 NuDAM modules an be romotely controlled on any RS-485 network from a host computer, via a single serial RS-232, allowing communication from as far as 4000 feet from the host. Based on the RS-485 multi-drop network system, each module has a unique address ID, whereby simple ASCII command & response protocols through the standard RS-485 interface can control all the NuDAM modules in the RS-485 network. The NuDAM modules provide direct communications with a wide variety of sensors, perform all signal conditioning, scaling, linearization and conversion, and can acquire measurements of temperature, pressure, flow, voltage, current, and multiple digital signal types.
-
Product
Ethernet Media Converter
MC-E Series
-
The MultiLink MC-E series makes it easy to use the power of optical fiber for extending Ethernet networks to remote locations. The fiber port is available in a variety of connector types and can support extremely long distance connections of up to 40km. With a built-in 2 copper port switch, it's also the fastest way to add multiple Ethernet drops to remote locations.
-
Product
DC/DC converter 5 W
20IMX7-03-8G
-
DC/DC converter 7 W from Bel Power Solutions | input ranges 8.4 - 36 VDC | output 3.3 V | operates in ambient temperature from -40 to +85 °C
-
-
-
Product
Optical Path Converter
LS512A/LS512B
-
There are many LED manufactories using two integrating spheres and one spectrophotometer to do test. The previous testing way is: when you use big sphere to test, the customer need to connect the detector cable and optical fiber from the Spectrophotometer to the big sphere, after the calibrating and then you can do the test. When you use the small sphere, you need to take away the detector cable and optical fiber from the big sphere to the small sphere, then need to calibrate again. It is too troublesome to take out the detector cable and optical fiber between the big sphere and small sphere, and you need to calibrate again for every change. The frequent change will also shorten the life of the detector cable and optical fiber.
-
Product
Analog Simulator
MPLAB® Mindi™
-
MPLAB® Mindi™ Analog Simulator reduces circuit design time and design risk by simulating analog circuits prior to hardware prototyping. The simulation tool uses a SIMetrix/SIMPLIS simulation environment, with options to use SPICE or piecewise linear modeling, that can cover a very wide set of possible simulation needs.
-
Product
BCD to Binary Converter
BCD250
-
Computer Conversions Corporation
The BCD Series of BCD to Binary Converters will convert 4 digits of scaled BCD angle data with a full scale of 359.9degrees into 12 Bits of binary angle data (MSB=180degrees). These units are entirely digital, require no timing or control signals and do this conversion in less than 500 nano-seconds. Logic levels are TTL/DTL compatable and +5V DC power is required. They are packaged in a 2.6 x 3.1 x .82" H PC board mounting module.
-
Product
Mini Optical To RF Converter
MX-O2RF
-
The Maxcom MX-O2RF series optical receivers are versatile, low-cost and compact optical receivers are versatile, low-cost and compact optical receivers for use as a tool for test and measurement
-
Product
DC/DC Converter 150 W
CQB150W-110S15
-
DC/DC converter with 150 W from Cincon | input ranges 43 - 160 VDC | output 15 V | operates in temperature from -40 to +105 °C | according to EN45545-2 fire and smoke
-
Product
Analog Oscilloscope
PS-500
-
*50MHz Vert. Band width*Sweep Time 23 Steps*Dual & Trace, ALT Trigger*Hold-off, X-Y operation*High Vert, Sensitivity : 1mv/DIV*High Sweep Resolution : 10ns/DIV
-
Product
Ethernet/LXI digitizerNETBOX 16 Bit Multi-purpose Digitizer - 20 MS/s on 4 Channels, 4 Single-Ended Inputs
DN2.592-04
Digitizer
The digitizerNETBOX DN2.59x series allows recording of one, two, four, eight or 16 synchronous channels with sampling rates of 20 MS/s up to 125 MS/s. These products offer outstanding A/D features both in resolution and speed as a remote instrument. The powerful A/D amplifier section offers 6 different input ranges, programmable offset and a software switching from single-ended (full number of input channels) to true differential (half number of input channels).
-
Product
Analog Test Solutions
ATX series
-
The ATX series of instruments are designed for applications that require an analog performance that is not achievable with industry standard platforms like PXI(e).
-
Product
6.5 Digit DMM / Digitizer PXI Card
GX2065
Digitizer
The GX2065 offers a unique combination of features, resolution, accuracy and speed in a compact, single slot 3U PXI format. Featuring 6- digit resolution, 0.005% basic DCV reading accuracy and up to 3,500 reading per second (rps) assures you of measurements that are accurate, fast and repeatable. All measurement functions including digitizing functions are isolated from the PXI bus - providing the ability to make true differential, floating measurements. An on-board controller performs all necessary DMM and digitizer calculations, minimizing PXI control bus overhead.
-
Product
Energy Saving Static Converter
-
The ENERGY SAVING static converter serves to generate a controlled squarewave single-phase alternate voltage (low frequency: 25 ÷ 125Hz) for industrial applications requiring high load power supplied by an external matching transformer. The power supply, sectioned by remote control switch and external fuses, is fed by a three-phase electric line via uncontrolled diode bridge and filtered by inductor and capacitor battery. The DC voltage thus obtained is converted into single-phase alternating voltage via “H”-shape bridge of semiconductors in order to control impressed frequency single-phase transformers.
-
-
Product
Catalytic Converter Measurement
OMCAT
-
OMCAT catalytic converter measuring systems provide a fast and efficient means of carrying out complex geometrical measurements on exhaust catalytic converters and of determining the gap bulk density (GBD). OMCAT measuring systems feature innovative measurement functions combined with reliable technology. High measurement speed and accuracy and high availability due to their rugged construction are the major strengths of these systems which come to the fore in the harsh conditions which prevail in production environments.
-
Product
PC/104 Analog Output Board
104-AO12-4
-
The following functions are available in many configurations giving the user the ability to specify exactly what’s needed. Interrupts are individually or globally enabled or disabled via software. A status register is provided to determine the interrupt source.
-
Product
Analog Voltmeters
-
*Dual stick MARK series measure voltage and perform phasing operations from 0V to 75kV*No batteries or calibration required*Determines in-phase or out-of-phase*Determines underground cable faults*Discharges underground cables and other equipment that hold capacitive charges*Versatile for overhead and underground applications
-
Product
- Single Mode to Multimode Converter
Model 279
-
FEATURES: DC to 2.5 MBPS; Full duplex; 850nm to 1300nm; In line mounting; Small size; Data LED's; Line Loss switch; Single-mode distance to 20 Kilometers. The Model 279 provides transparent conversion between fiber optic devices utilizing multi-mode fiber and those with single-mode fiber.
