Product

SHV Connectors

-

Pasternack Enterprises, Inc.

Pasternack Enterprises, Inc.

Pasternack SHV connectors category has several part numbers, most are RoHS and REACH compliant. SHV connector series in this category will terminate to coax or terminal. These SHV connectors are built to precise microwave and RF industry specifications. SHV connector items are built in jack or plug gender with 50 Ohm impedance. Connectors in SHV series are available in bulkhead, 4 hole panel or mountless options. These SHV connector designs include clamp/solder, crimp/solder or solder attachment methods. As with other over 40,000 RF, microwave and millimeter wave Pasternack products, this SHV connector series is in-stock. Not just are they in stock, but these radio frequency connectors will ship the same day as they are purchased.

Product

2", 4", 6", 8" or 11" Large-Digit Displays

Grand Series

-

Laurel Electronics, Inc

Grand Series - Laurel Electronics, Inc

Available with 57 mm (2.2"), 102 mm (4.0"), 144 mm (5.7"), 200 mm (7.9"), or 280 mm (11.0") digit height for clock, timer, totalizer, frequency and rate inputs. RS-422 and dual-relay output options.

Product

Near Field Microprobe E-field 7 MHz to 3 GHz

ICR E150

-

Langer EMV-Technik GmbH

ICR E150 - Langer EMV-Technik GmbH

The near field microprobe is used to measure electric fields at extremely high resolution and sensitivity. The optimal distance to the object being measured is < 1 mm. Due to its small probe head dimension, the probe has to be moved by a manual or automatic positioning system, e.g. Langer-Scanner.

Product

Flatness, Bow, Warp, Curvature, Glass Thickness

Standard Warp Measuring System

-

Optik Elektronik Gerätetechnik GmbH

Standard Warp Measuring System - Optik Elektronik Gerätetechnik GmbH

Optical, non contact measurement of warp and bow of specimen with size up to (1600 x 1200) mm. The system is designed for the contactless, optical measurement of the curvature (Warp) horizontal, coated float glass substrates. For that measurement the heights on different measuring points is evaluated.

Product

IEC60335-2-9 Clause 3 Figure 104 Vessel For Testing Induction Hotplates

CX-104

-

Shenzhen Chuangxin Instruments Co., Ltd.

CX-104 - Shenzhen Chuangxin Instruments Co., Ltd.

IEC60335-2-9 clause 3 figure 104 Vessel for testing induction hotplates Parameter : Pot and lid material is mainly Q235, carbon mass fraction <0.08%; 2. The thickness of the wall material is 2 mm;3. The bottom of the pot body can not be outward convex, can not exceed 0.05mm; 4. Pot body and lid surface to be clean 5, size: 110, 145, 180, 220, 300mm each one

Product

2.92 mm to 2.92 mm Test Cable

C50292MM

-

Copper Mountain Technologies

C50292MM - Copper Mountain Technologies

Our 2.92 mm test cable is made to ideally suit our larger line of vector network analyzers. The C50292MM test cable operates at a frequency of 40000 MHz and is compatible with our PC-driven vector network analyzers.

Product

Terminations

-

Pasternack Enterprises, Inc.

Pasternack Enterprises, Inc.

Our RF termination loads (also know as terminators) are available in 1.85mm, 2.4mm, 2.92mm, 4.1/9.5, 4.3-10, 7/16 DIN, BMA, BNC, Type C, Mini SMP, MMCX, Type N, QMA, SMA, SMB, SMC, SMP, SSMC and TNC connector types. RF termination loads from Pasternack are organized into two categories, feed-thru terminations and RF terminations. Pasternack Enterprises RF load terminations include precision and standard versions and many are RoHS and REACH compliant. 0.25 Watts, 0.5 Watts, 1 Watts, 2 Watts, 5 Watts, 10 Watts, 25 Watts, 50 Watts and 100 Watts models. Pasternack RF terminations are offered with impedances of 50 Ohm, 75 Ohm or 93 Ohm. The frequency ratings for these RF coaxial load termination range from DC to 50 GHz. RF loads are available in female, jack, male, male to female and plug genders. Our RF termination loads varieties are RoHS and REACH compliant. As with our other over 40,000 RF, microwave and millimeter wave components from Pasternack, this RF terminator series is in-stock. Not just in stock, but also these RF terminations will ship the same day as they are purchased from Pasternack.

Product

Integrating Sphere Light Sources

-

Gigahertz-Optik GmbH

Gigahertz-Optik GmbH

Integrating sphere light sources with LED based or continuous broadband emission spectrum for use as luminance standards for camera calibration, for the determination of veiling glare, for the adjustment of night vision devices and much more. Diameters in the range from 50 mm to 500 mm with options like monitor detector, signal output control by manual and remote apertures and much more.

Product

Inductive Sensors

-

4B Components Ltd.

4B Components Ltd.

Inductive sensor designed to detect shaft speed, shaft position, gate position, or object presenceTotally sealed constructionMulti-voltage 24 - 240 VAC/VDCDetects ferrous targets up to 5/16" (8 mm)IP 65 Protection

Product

Benchtop/Portable Cable/Harness Wiring Test System

CKT1175-10

-

CK Technologies, Inc.

CKT1175-10 - CK Technologies, Inc.

Designed for wiring testing requirements requiring up to 2,000 test points, the CKT1175-10 is ideal as a benchtop or portable test system. The system is packaged in an enclosure specifically designed to be used in rugged environments. The basic 500 test point system is 20.5 in. (521 mm) wide X 12.0 in. (305 mm) high X 16.05 in. (408 mm) deep; the 500 test point expansion units are 20.5 in. (521 mm) wide X 6.00 in. (153 mm) high X 16.05 in. (408 mm) deep.

Product

Adapter, 1.0 mm (m) to 2.4 mm (m), DC to 50 GHz

11922A

-

Keysight Technologies

11922A - Keysight Technologies

The Keysight 11922A precision 2.4 millimeter coax in adapter offers a simple way of measuring coaxial devices at higher frequencies. It is designed for the measurement of components with 50 ohms impedance and a frequency range from dc to 50 GHz.

Product

pH Electrode Holder

PF12

-

optek

PF12 - optek

Extension of optek sensor bodies for inline pH measurement in industrial installations of various applications. Commonly available Ø 12mm & 120 mm length pH probes can be used and are positioned at an optimum angle into the process stream.

Product

SINE (Sinusoidal) Targets & Arrays

-

Applied Image, Inc.

Applied Image, Inc.

Sinusoidal Target Arrays have been recognized as a superior test method for a variety of applications, from moiré contouring to reliable MTF Evaluation of materials, lenses, cameras, and electro-optical systems (Follow the hyperlink to learn about using Sinusoids for MTF eval). Sinusoidal Pattern Arrays are manufactured on two different materials for both reflective and transmissive applications. Because of the inherent limitations of reflective materials, the maximum spatial frequency of the reflective pattern arrays is limited to 20 cycles per mm, while the transmission film arrays are offered in various sizes up to 256 cycles per mm. In addition, the sinusoidal arrays are available in a Single Frequency Grating or with Multi-Frequency Gratings. If instead of continuous sinusoidal frequency, you are looking for a square wave frequency design, then look to the Ronchi Gratings page. Should you need to alter the size of the pattern or the substrate, fill out our Custom Test Targets and Charts form and start the conversation.