Distortion
See Also: Total Harmonic Distortion, Intermodulation Distortion, Noise, Distortion Analyzers, Distortion Meters, SINAD
-
Product
HandyScope HS5: 500 MS/s 250MHz BW, 2 Channel, USB Digital Storage Oscilloscope, 40MHz AWG, Spectrum Analyzer, Voltmeter, Transient Recorder
HS5-540XM-W5
-
The Handyscope HS5 is the first USB oscilloscope (USB powered) sampling at 500 MHz, with a 14 bits resolution and a 250 MHz bandwidth. This makes it possible to analyze very fast signals with very small amplitudes. The smallest distortions can be revealed due to the high resolution and bandwidth. Because of the deep memory (up to 64 MSamples on one channel), long record measurements are available for intermittent phenomena and Fast Fourier Transform calculations with over 32 million spectral lines can be performed. Using very fast FFT algorithms, an FFT with 1 million spectral lines can be performed within a second.
-
Product
Modulation Analyzers
-
Provides precision modulation and audio analysis in a single, easy-to-operate package. Measures AM, FM, PM, carrier and audio frequencies, SINAD, distortion and carrier level.
-
Product
Programmable AC Power Source
LSP-500VAC
-
• Applied with the AC-DC-AC inverter technology and digital waveform synthesis & waveform feedback technology, low distortion power; • Applied with entire cycle high-precision measurement technology and high-speed sampling technologies, panel of instrument will directly and accurately displays the power output of the voltage, frequency, current, active power and power factor to achieve the integration of the source table; • Applied with SCM control and measurement technology, high intelligence; • Applied with zero output impedance technology, the output equivalent impedance is almost zero and further improve the stability of power supply; • Applied with isolated floating output technology, the power output and input have good isolation, floating output, conducive to make sure power itself safety and operator’s safety; • Perfect voltage, current anomalies and overheating protection, improve the reliability of power supply; • Applied with power limiting technology to avoid strong interference on the power grid and other electrical equipment, while facilitating reliable operation of the power supply itself; • The input voltage can be option via a toggle switch of panel mains 110V/220V; • The initial phase and end phase of the output voltage waveform can be set {0°-359° (±1°)}; • Measurement process can be programmed to control (1 to 50 memory groups, 1 to 9 steps for each memory group);
-
Product
Flexible Rope-Type Current Probe
RCT1A and RCT5A
-
These probes have great bandwidth ensuring accurate measurement even with harmonically distorted wave shapes. For all RCT1A/RCT models, a NIST, NAVLAP, NPL (UKAS) factory traceable calibration certificate and certificate of conformance is supplied. UL/CSA approved materials are used throughout. Three phase and single phase flexible AC current sensors (rope sensors) are available for fast installation in confined spaces, eliminating the need for Electrical Supply Shutdown. Available outputs are 1A @ 2.5VA and 5A @ 0.5VA, this means long cable lengths from current sensor to signal conditioner allow these low VA ratings to be used, even when feeder cable to energy meter distances are large (up to 98 feet / 30 meters)
-
Product
Digital Power Meter (High Accuracy Model)
LS2050
-
LS2050 digital power meter is a new generation intelligent product which adopts digital sampling technology to analysis of the waveform. It has the following features: • Three windows digital display which reduces reading error, intuitive and convenient • Adopts high speed MCU and high precision A/D to control and measurement • All measured data as virtual value, also suit to signal waveform distortion • Fast test • Equipped with RS232 communicate function, can use upper computer software to carry on remote operation, control and read corresponding data, the test data and waveform could be displayed in the PC, Chinese and English operation interface, high intelligent instrument • This instrument provides two kinds of method to calculate total harmonic distortion (THD), IEC and CSA.
-
Product
Automated Test Interface
ATI-100
-
Matrix Test Equipment Incorporated
Now, with our ?New? Model ATI-100 you can turn your existing Matrix Signal Generator and Switchable Filter Bank into a full-blown DTS (Distortion Test System). Plug and play is the word, just plug in your Multiple Frequency Signal Generator, Switchable Filter Bank, Spectrum Analyzer, Oscilloscope, Power Meter, Frequency Counter, etc. to allow the following automatic testing with a single insertion of DUT (device under test
-
Product
Dynamic Calibration for ROSS Streak Cameras
DynaCal
-
The DynaCal Optical Calibration Module (OCM) is designed exclusively for the Sydor ROSS Streak Camera to ensure accuracy, both over time and in situ, so you can be confident that the data from your shot is certified to be correlated to the calibration of your camera. The beauty of in situ calibration is that the cost of removing and resetting the camera is avoided—and so is the risk of the replacement of the camera and shifting or disturbing the sensitive nature of streak camera results. Only in situ calibration will reveal the real world effects of EMR, gravity, electronic noise and more when they distort your camera results.
-
Product
3-Phase Relay Testing System
TRES
-
With high power outputs packaged in an extremely compact and rugged system, the TRES has a tremendous power-to-weight ratio. The design incorporates the latest in modern digital microprocessor technology to achieve unbeatable output characteristics in terms of power, accuracy, low distortion, and dynamic capability. This hi-tech solution enables the testing of many different functions required in relay testing without the need of additional accessories.
-
Product
Time Code Distributor/Reshaper
SR-112
-
Like it’s big brother the SR-112 Distripalyzer, the SR-28 can drive time code over long cables, making it ideal for synchronization during live shows and remote recording. The SR-28 time code distributor, with two inputs and eight outputs, reshapes time code while distributing it, eliminating amplitude distortions and level fluctuations. The level of each output is individually adjustable via front panel pots. The input is selected via a front panel switch. Also included are 2 power inputs and an automatic switch over in case of failure.
-
Product
PXIe-5654, 10 GHz or 20 GHz RF Signal Generator
783126-01
RF Signal Generator
The PXIe‑5654 features an ideal combination of exceptional phase noise and frequency tuning time. These features address applications such as blocker test/receiver desensitization, high-performance intermodulation distortion measurements, and various electronic warfare applications. The PXIe‑5654 is designed to meet the challenging requirements of RFIC characterization, satellite test, and radar applications.
-
Product
Operational Amplifiers
-
Operational amplifiers from ams are ideally suited to audio applications. These CMOS devices are available as single, quad or differential amps. They feature good common-mode rejection, have low input bias currents, good gain bandwidth, low total harmonic distortion and an excellent rail-to-rail output-drive capability of 200mA peak.
-
Product
Test Solutions Services
-
Spinnaker Contract Manufacturing, Inc.
As standard practice, all of our SMT assemblies are washed and tested through our Automated Optical Inspection and pass through our stringent internal QA/QC policies. In Cables and Wire Harnesses, pretests, such as pull tests and crimp type tests, are performed on all builds before being tested for continuity, hi-pot, shorts and mis-wires, to name a few. Our electromechanical assemblies are capable of receiving full functional testing through custom test fixtures and RF test. Some RF tests include Gain/Loss, Frequency Response, VSWR (Voltage Standing Wave Ratio), Inter-Modulation Distortion and Output Power.
-
Product
500 / 1000 / 1500MHz Synthesized Signal Generator
Model 2100 Series
-
- Combine with DDS and PLL Techniques- 1500MHz Maximum Frequency- 1 ppm High Accuracy, Less Distortion- Dual Independent Outputs- AM, FM, FSK, PSK Modulation
-
Product
47~1050MHz FTTH Top Ultra Low Light Receiver
H9122TG
-
Hangzhou Huatai Optic Tech. Co., Ltd.
H9122TG, operating bandwidth of 47 ~ 1050MHz, is a top-level type, ultra low optical CATV receiver, regardless of the aircraft for analog television or digital television, have high reception sensitivity and excellent intermodulation distortion index. Built-in light AGC, a high optical power when receiving, play limiter output, so H9122TG at + 2 ~-24dBm large dynamic range of received optical power, and have excellent characteristics.
-
Product
Distortion Analyzer
SINAD
-
SINAD utilizes the latest in Digital Signal Processing (DSP) technology to accurately measure several key performance characteristics of radio receivers by analyzing the spectral content of a received audio signal.
-
-
Product
Intermodulation Distortion Measurements
S96087B
-
Easily set up and calibrate swept intermodulation distortion measurements (IMD) measurements using the S96087B software application with the ENA
-
Product
Satellite TV External Modulation Optical Transmitter
HES-26S ( 950~2600MHz )
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai 1550nm satellite TV external modulated optical transmitter HES-26S, adopts external modulated technology, no laser chirp, very low dispersion distortion, high extinction ratio. It applies to long distance, high quality network application. It can transmit 950~2600MHz satellite SAT-IF signal through one fiber.
-
Product
Air Core Line & Load Reactors
-
Line and load reactors are generally serial-connected to the input and/or output terminals of three phase equipment such as motor speed controllers, inverters and UPS systems. These equipment make use of semiconductor switches such as IGBTs, thyristors, and diodes and therefore create harmonic distortion and high switching over-voltages (dv/dt). Use of such equipment has been becoming more widespread as the technology advances. However, the negative effects of these equipment should not be overlooked.
-
Product
AC / DC Digital Power Analyzer
4016（800Vp,20Arms/200Ap）
-
To analyze AC/DC power source, it requires a lot of parameters. Such as voltage(V), current(A), power factor(PF), Total Harmonic Distortion(THD), Crest Factor(CF), Inrush current, etc. To meet power saving regulation, the standby power measurement must be done. In this video I will show you how to operate this Prodigit Power Analyzer 4016. Furthermore, I explain what the parameter's meaning.
-
Product
Diversity Receiver
R400a
-
The R400a is a high performance, triple-conversion, frequency synthesized, UHF receiver fully compatible with all Lectrosonics 400 series transmitters, and a number of analog models. The proprietary audio processing includes a DSP (digital signal processor) for very low distortion and a superior signal to noise ratio. The DSP eliminates a compandor and its artifacts to provide exceptional audio quality when operating in its native hybrid mode. Special DSP algorithms also provide compatibility modes for use with Lectrosonics 100 and 200 Series analog transmitters.
-
Product
PROBE MICROPHONE ICP
377B26
-
Open Circuit Sensitivity (at 250 Hz)Frequency Range (+2.2/-4.9 dB)2 to 20000 HzLower Limiting Frequency (-3 dB)Inherent Noise<45 dB(A) re 20 Pa Dynamic Range(3% Distortion Limit)EnvironmentalTemperature Range (Operating)-40 to +158 F-40 to +70 C[5]
-
Product
Class 2 Sound Level Calibrator
SPC70
-
The SPC70 is a Class 2 sound level calibrator suitable for periodic testing of sound level meters and verifying their accuracy before and after readings, in accordance with international standards. The SPC70 is simple to use and provides a 1kHz reference at 94dB and 114dB. The output is accurate to 0.5dB with low levels of harmonic distortion. The SPC70 is compatible with the Martindale SP79 Class 2 Sound Level Meter and other meters with microphones up to 25mm.
-
Product
47~862MHz AGC FTTH Digital TV Two Output Low AGC Optical Receiver
H9222LG
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai H9222LG, operating bandwidth of 47~862MHz, is a suitable digital television FTTH applications, ultra-low optical receiver, Whether the machine is used analog television or digital television, have high reception sensitivity and excellent intermodulation distortion index.. Due to the built-in optical AGC, at high optical power receiver, played limiting output, so H9222LG in the received optical power over a large dynamic range of +2 dBm ~-21dBm, and have excellent properties.
-
Product
Dual-Channel Precision Audio Analyzer with Built-In Condenser Measurement Mics
PAA6
-
Essential tools, such as the Phonic PAA6 Professional Audio Assistant generally wind up at the bottom of pro audio wishlists after esoteric preamps, compressors, and EQs. But more often than not, the key to great sound lies in the utilitarian gear, particularly, the Phonic PAA6 audio analyzer. If you want to get the most out of your studio equipment or PA system, the PAA6 should be at the top of your bucket list. A highly accurate measurement tool, the elegant touch screen interface of the PAA6 offers unfettered access to 61-band real-time spectrum analysis; Fast Fourier Transform (FFT); sound pressure (SPL) and dBu/dBV line voltage measurement; EQ setting; phase and polarity check; LEQ (equivalent continuous noise level); audio oscilloscope; and RT-60 functions. The PAA6 also has two built-in condenser measurement mics that can be used in six different positions. If sound is your product or passion, the Phonic PAA6 is perhaps the wisest investment you can make for your studio or sound reproduction system. Whether you're setting up monitors, treating room characteristics, calibrating listening levels, or want to know the harmonic distortion and noise characteristics of your workhorse preamps to ensure clean mixes, the Phonic PAA6 is your key to the best possible quality sound.
-
Product
Programmable AC Source
6500
-
Chroma Systems Solutions, Inc.
1200VA ~ 9KVADirect Digital Synthesis (DDS) waveform generationProgrammable voltage, current limit, frequency, phase, and distortion
-
Product
TDR Structural Health Monitoring
-
Material Sensing & Instrumentation
MSI Time-Domain-Reflectometry (TDR) Structural-Health Monitoring probes the structural health of a composite part by propagating a fast electrical pulse along a distributed linear sensor which has been fabricated directly in the laminate. The sensor is formed from the native graphite fibers already used in composite manufacture, and constitutes zero defect. Fibers are patterned into a microwave waveguide geometry, or transmission line, and interrogated by a rapid pulse as shown below. Structural faults along the line cause distortions in waveguide geometry, producing reflected pulses similar to radar. Cracking, delamination, disbonds, moisture penetration, marcelling, and strain are all detected by propagation delay, for sensor lengths up to several meters.
-
Product
1 / 2 / 3 MHz Multi-Waveform Signal Generator
MSG1M / MSG2M / MSG3M
-
- Wide frequency range- Sine, triangle, square, ramp, pulse, TTL (Sync) & DC outputs- Low distortion high resolution on low frequency output attenuation up to 80dB- Variable DC offset control- Four digit digital display with frequency indication in Hz, KHz, MHz/Amplitude display
-
Product
Programmable AC Power Source
Model 8600 Series
-
- Compact size and light weight, standard 19″ rack construction- Step-less frequency setting from 45 to 450Hz- Very low distortion sine wave output- Output voltage range selectable 135 or 270V AC- Galvanically isolated input/output- Independent on/off switch for input and output- 16×2 vacuum florescent display for parameter display- Complete operation through push switches and a digital rotary encoder- Automatic protection against overload, short circuit and over temp.- Built in PFC to provide 0.99 input power factor and wide input range- Conforms to EN55022, class A, safety standard EN60950
-
Product
Adjustable High Frequency Reference Ballast
HCS-109A
-
HCS-109A Adjustable High Frequency Reference Ballast also called High Frequency Current Source. Comparing to IEC Test Method, HCS-109A is an Equivalent Test Method which is economic solution. HCS-109A equipped with Spectrophotometer & Integrating Sphere Test System. It can also measure the photo, color and electricity parameters for high frequency fluorescent lamp.Specifications: • Input voltage: 200V~240V, 50/60Hz • Input Power: 80 W max • Output Current: 130mA~400mA (Adjustable), accuracy: +/- 1% • Output Frequency: 25kHz< +/-2.0% (Adjustable), accuracy: +/- 0.3kHz • Output current total harmonic wave distortion: THD<2.5% (HF current wave)
