Hardware in the Loop Simulation
See Also: HIL, HWIL, HiL Simulators
-
Product
AFDX ® / ARINC 664 Test And Simulation PXI Module
PXI-C664
-
*Supports IEEE 802.3 10/100/1000 Mbit / s full duplex Ethernet connections*Uses SFPs to support both electrical and optical interfaces*Half-size PCI / PCI-X modules*Simulates multiple AFDX® / ARINC 664 end systems*Stard Ethernet processes simultaneous to AFDX® / ARINC 664*Up to 128 output VLs and 512 input VLs*Upper layer protocol handling (ARINC 653, UDP, IP) managed onboard*DMA for high data rate applicationsWindows XP / 7, Linux, and LabVIEW Real Time Drivers & APIs (others on request)*Easy to use tool for configuring AFDX® / ARINC 664 end systems (XML based)
-
Product
Solar Simulator Continuous Light
-
This type of solar simulator uses Xenon high pressure arc lamps as light source. These lamps have a colour temperature near 5800 K, so it is feasible to filter the light output to an excellent AM 1.5 spectrum. If a tuneability of the spectrum is required, these lamps can be combined with tungsten lamps to achieve multi-source solar simulators. These can be used to measure tandem/triple/multijunction solar cells. They also allow detailed analysis of all types of solar cells using a spectral metric (see : Publication List).
-
Product
Data Acquisition Hardware: USB
-
Ease of connection, low cost and good performance are key to our USB product range.
-
Product
Secure Hardware Platforms
-
With our STSECURE portfolio, STMicroelectronics offers secure microcontrollers that answer the market needs for advanced security. We deliver hardware-certified solutions based on advanced flash technology, with our latest generation implementing an ARM® SecurCore® processor.
-
Product
Antenna, Active Loop
EM-6876 | 9 KHz – 30 MHz
-
The Electro-Metrics EM-6876 Active Loop Antenna is used with EMI Receivers and Spectrum Analyzers with 50 ohm input and covers the frequency range of 9 kHz to 30 MHz.
-
Product
MIMIC SNMP Simulator
-
MIMIC SNMP Simulator creates a network of up to 100,000 SNMP manageable devices on one server. You can simulate any SNMP based device with any number of public or private MIBs to run a large variety of device configurations with your SNMP management application. It lets you generate thousands of traps to simulate disaster scenarios.
-
Product
8 Port BRI-S/T ISDN Simulator
BRI-8ST
-
The unit has 8 S/T ports allowing ISDN basic rate terminal equipment to be connected together just as if they were connected through the ISDN network.
-
Product
Windows Server Simulation Software For BACnet Systems
BACSim
-
BACsim is the industry's first easy-to-use BACnet device simulator for Windows. BACsim runs under Windows 7/8/10 and Server 2012, and provides a robust set of basic simulator features tailored to the needs of BACnet designers and testers.
-
Product
PXI Dual 8 Channel Switch Simulator
40-485-121
-
Designed to simulate the operation of automotive switches where dirty contacts or leaking current can be expected from switch contamination. It allows automotive I/O devices to be tested for correct operation under adverse conditions.
-
Product
UE Simulator
-
With Simnovus, you get superior value as our software runs on COTS and SDR enabling you to deploy multiple test beds. You do not have to spend millions on expensive Capex.
-
Product
ELECTRIC BRAKE FORCE METER WITH DYNAMIC LOAD SIMULATION AND CIRCUIT TESTING
MDTT9107
-
*Tests truck-side brake controller output and all towing-lighting functions without a trailer*Displays real-time brake controller output gain and timing*Quickly troubleshoots electrical circuits and ground condition*For use with aftermarket and integrated brake controllers*Microprocessor controlled; simulates trailer brake loads*25' cable allows one-man, in-cab testing of brake controller and all truck-side tow circuits*Use to verify that the vehicle’s adaptive (speed/load sensitive) brake-controller output is functioning properly
-
Product
PXI Fault Insertion Switch, 7-Channel, Two Fault Buses, 20 A, Hardware Interlock
40-194A-002-HI
-
The 40-194A-002 is a 7-Channel Fault Insertion switch with hardware interlock and two fault buses, designed for the simulation of fault conditions in automotive systems. As well as high current handling of 20A, very low currents can also be switched.
-
Product
HiL Simulators
NovaCarts Battery
-
Exact cell simulation for validating battery management systems (BMS). "NovaCarts Battery" represents one of the most powerful and precise cell simulation systems on the market. This is leveraged by the modular and scalable HiL system to create optimum conditions for developing new battery management functions such as state-of-charge (SoC) and state-of-health (SoH) controls, active cell balancing and electrochemical impedance spectroscopy.
-
Product
Large Area Solar Simulators
-
The LASI Beam Turner assembly allows the output of the LASI to be projected horizontally. It attaches to to the standard LASI downward facing stand that is included in the base LASI system.
-
Product
Quad Digital Receiver Hardware
DP-VME-5841
-
DP-VME-5841 is a VME-based quad digital receiver hardware module, which measures the pulse parameters of RADAR in the real time. This module is particularly suited for radar systems, where the signals must be sampled at a high rate and very high purity programmable signal generation.
-
Product
2 PRI + 32 BRI-S/T ISDN Simulator
CH-32BRI-ST-MOD-2PRI
-
This unit has two PRI ports and 32 BRI ports allowing ISDN equipment to be connected together just as if they were connected through the ISDN network
-
Product
PXI/PXIe Battery Simulator Module, 6-Channel, 1 KV Isolation
41-752A-101
-
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 6-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture. The 750 V or 1 kV isolation barrier (version dependent) allows the module to be used as a lower power version of a battery stack, representative of those used for vehicle propulsion.
-
Product
Electrostatic Discharge Simulator
ESD61000-2
-
ESD simulator (Electrostatic Discharge Generator or Electrostatic Gun) is in full compliance with IEC 61000-4-2, EN61000-4-2, ISO10605, GB/T17626.2, GB/T17215.301 and GB/T17215.322. The ESD generator is designed for the assessment of electrical and electronic equipment to withstand ESD performance. ESD61000-2/ESD61000-2A has LCD display in both English and Chinese, they equipped with an infrared remote control which can allow you do the test in some special place.
-
Product
Date & Time Simulation Software
TimeShiftX
-
TimeShiftX is a date and time simulation software that lets you time travel software into the future or past for temporal testing all date and time sensitive functionality and code such as end of year/month, daylight savings, leap year, billing, rates, policies, etc. Perform time travel testing instantly, without any code changes, manual work, or server isolation
-
Product
ARINC825 (CAN Bus) Test & Simulation Module for PCIe
ACPe825-x
-
ARINC825 (CAN bus) Test & Simulation module for PCIe with 2 or 4 electrically isolated CAN bus nodes operating concurrently at CAN bus high speed bit rate of up to 1Mbit/s. The ACP825 PCIe card can work either with full functionality as an active CAN node for testing and simulating or in Listening Only mode for monitoring and recording purposes.
-
Product
Hardware Enabled SaaS Solution Quantifying Methane Emissions
MethaneTrack™
-
NevadaNano’s MethaneTrack™ is a low cost network of rugged monitoring points to measure methane emissions and report leak location and size to the operator. Utilizing an Industrial IoT (IIoT) network to detect methane in the air, MethaneTrack™ detects fugitive and operational emissions from a site and immediately alerts the operator of the location and volume of the emissions, facilitating rapid response and repair. Autonomous, continuous monitoring enables up to 99% reduction in emissions while reducing operational costs and boosting profits.
-
Product
Tailor-Made to Simulate Low-Temperature Plasma Sources and Systems
Plasma Module
-
The Plasma Module is tailor-made to model and simulate low-temperature plasma sources and systems. Engineers and scientists use it to gain insight into the physics of discharges and gauge the performance of existing or potential designs. The module can perform analysis in all space dimensions 1D, 2D, and 3D. Plasma systems are, by their very nature, complicated systems with a high degree of nonlinearity. Small changes to the electrical input or plasma chemistry can result in significant changes in the discharge characteristics.
-
Product
PMC Module With 2 Or 4 CAN Bus Nodes ARINC825 Compliant For Testing & Simulation Of Avionic CAN Bus Systems
AMC825-x
-
ARINC825 (CAN bus) Test & Simulation module for PMC with 2 or 4 electrically isolated CAN bus nodes operating concurrently at CAN bus high speed bit rate of up to 1Mbit/s. The AMC825-x PCI Mezzanine Card (PMC) can work either with full functionality as an active CAN node for testing and simulating or in Listening Only mode for monitoring and recording purposes.
-
Product
2 PRI + 16 BRI-U ISDN Simulator
CH-16BRI-U-MOD-2PRI
-
This unit has two PRI ports and 16 BRI ports allowing ISDN equipment to be connected together just as if they were connected through the ISDN network
-
Product
PXI/PXIe Battery Simulator Module, 6-Channel, V/I Readback, Simplified Current Sink, 750 V Isolation
41-752A-911
-
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 6-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
Simulation Software and Test Solutions
Simcenter Software
-
Siemens Digital Industries Software
The Simcenter portfolio uniquely combines 1D simulation, 3D CAE and test to help you predict performance across all critical attributes earlier and throughout the entire product lifecycle. By combining physics-based simulations with insights gained from data analytics, Simcenter helps you optimize design and deliver innovations faster and with greater confidence.
-
Product
MIL-STD-1553 Test & Simulation Instrument for VXI
VXI-1553
-
Avionics Interface Technologies
Dual redundant, multi stream configurations availableSoftware selectable Transformer, Direct, and Bus Stub Coupling Modes - Concurrent Bus Controller, 31 Remote Terminals, & Bus Monitor operation - Full error injection and detection - Multi-level trigger for capture and filtering - IRIG-B time code encoder/decoder - Real-Time recording and physical bus replayANSI Application interface supporting C, C++, C#, and .NET development - VISA based VXI “Plug & Play’ Device driver provided
-
Product
PXI Battery Simulator Modules
-
These PXI battery simulators are designed to simulate the power supplies of portable battery powered equipment and the single cell (model 41-753) is particularly suitable for cell phone testing. These modules can source current to simulate a battery supply or sink current to simulate a battery under charge.
-
Product
16CH Battery Cell Simulator
Chroma 87001
-
Chroma Systems Solutions, Inc.
Chroma 87001 Battery Cell Simulator is a high precision, programmable, and bidirectional DC power source with both voltage source and current source functions. In addition, the model can be used as a multi-channel DC power supply or an electronic load as well. A single simulator has 16 channels and each of them can set voltage and current respectively via Chroma software.
-
Product
Satellite Simulators
-
Tampa Microwave''s satellite simulators provide a compact easy to use training and evaluation tool for satellite earth terminals. We provide a variety of models with different combinations of frequency bands, transmit/receive strength, atmospheric effects and form factors. Contact us with your requirements and we will recommend a cost effective solution.
