Hardware in the Loop Simulation
See Also: HIL, HWIL, HiL Simulators
-
product
Loop Calibrator
Model KM CAL-904-MK1
Kusam Electrical Industries Limited
• 4-20mA (1kΩ Load, 24V Loop Output).• 0-20mA and 0-24mA output ranges.• 0.025% Basic Accuracy.• Auto Ramp and Step functions.• 0-100% output with percentage step option.• 0-24V DC voltage source.• Open loop and overload buzzer alarm.• Low battery indication.• Simple Operation Interface• Warning beeper when output is open• Pollution Degree 2.• Ambient temperature 0~40℃.• Power Consumption 150mA at 24V 1kΩ load
-
product
4, 8, 16 Or 32 Channel ARINC429 Test And Simulation Modules For VME (6U)
AVC429-x
Integrated modular solution by using the AMCX429-x PMC cards installed on AIM’s AVC-2 Generic VME64x (6U) carrier card.
-
product
Battery Simulator
G5.BAS
The G5.BAS series is bidirectional regenerative. It was developed specifically for the simulation of energy storage devices and batteries and is suitable for use in laboratories and on test benches. The modular and finely graded G5.BAS series is characterized by highly dynamic response times and a wide current-voltage range with an auto-ranging factor 3.
-
product
ARINC-708/453 2-Channel Test & Simulation Module for the Weather Radar Display Databus
M8K708
The M8K708 module is an ARINC-708 / 453 2-channel test and simulation module for the Weather Radar Display Databus. The M8K708 supports two ARINC-708 / 453 channels, each selectable as transmit or receive. Each channel implements an 64K×16 FIFO and supports polling and/or interrupt driven operation.The M8K708 comes complete with Windows software, a C-driver software library including source code and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application. In addition, Excalibur produces adapter cables that convert the carrier board I/O Molex™ connector to two twinax CJ70-49 connectors. The cable may be purchased at an additional cost.
-
product
IntelliPoint RF - Loop Powered Level Switch
The IntelliPoint Loop Powered Two Wire provides a capacitance probe level switch with current output and “On-Board” self-diagnostics to ensure reliability and level sensing elements for a wide variety of temperatures, pressures, and materials.
-
product
DDS Phase Locked Loop Synthesizer
DDS Series
*Connectorized Package *Programmable Frequencies to 1 GHz
-
product
Short Circuit Loop Impedance Meter
AMZC-305
Loop impedance measurement with resolution 0,01Ω ; Loop impedance measurement without tripping the circuit breaker > 30mA with resolution 0,01Ω (100...440V) ; Measurements possible in installations 110/190V, 115/200V, 127/220V, 220/380V, 230/400V, 240/415V, 290/500V and 400/690V (range 100...750V)
-
product
BOSS Simulator
Softdel’s BOSS Simulator is a sophisticated BACnet monitoring, debugging and simulation program that runs on any Windows® computer. It has a simple interface that is easy to use for BACnet professionals as well as novices. BOSS Simulator extends the functionality of Softdel’s BOSS Explorer by adding complex simulation and troubleshooting features, including support for A-side and B-side services, device discovery across routers and auto command generation across the entire network.
-
product
LED DC Electronic Load Simulator
3340G Series（150W~300W）
Each 3340G Series module has its own control and display panel, LED/CC/CR/CV/CP/ Dynamic modes, plug in 3300F with 150 sets Store/Recall memory which provides load set-up more efficiently，also can be controlled intranet via RS232、Ethernet、USB and GPIB interface.
-
product
Loop Antennas
A.H. Systems' designs, manufactures and delivers high performance Loop Antennas for a wide range of magnetic field testing. Whether used in a set to measure shielding effectiveness per MIL-STD 285 and NSA 65-6 or individually to satisfy specific requirements,
-
product
Inflight Entertainment System Hardware
Innovative IFEC solutions that enable connectivity, entertainment, and control.
-
product
PXI Strain Gauge Simulator Module 4-Channel, 2k
40-265-304
The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 4-channel, 2kΩ) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions.
-
product
MEMS Sensor Simulation
SimSENSOR
Performance testing of sensor fusion in MEMS inertial and multi-GNSS navigation systems. SimSENSOR extends the capabilities of Spirent’s multi-GNSS simulators by simulating MEMS sensor outputs on a common trajectory with the simulated GNSS RF signals. The simulated MEMSs sensor outputs include user control of representative noise and errors (bias/drift).
-
product
Troposcatter Simulator
HTSS
Hollis Electronics Company LLC
Hollis Electronics HTSS is a quad diversity Troposcatter channel simulator which interfaces with your radio equipment at 70 MHz IF. The complete digital implementation provides high accuracy and exact repeatability. An integrated AWGN noise source coupled with an internal power meter supports accurate setting of SNR and Eb/No.
-
product
Hardware Modules for PXI, PCI, PCI Express, USB, Ethernet, VME, and VXI
MIL-STD-1553
Avionics Interface Technologies
MIL-STD-1553 hardware modules for PXI, PCI, PCI Express, USB, Ethernet, VME, and VXI provide advanced features and functionality to support even the most demanding test and simulation applications.
-
product
Impulse Noise Simulators
INS Series
A simulator to reproduce fast rise-up noises which are generated when switching ON / OFF electric current on the inductive load. It can be used for performance evaluation of electronic equipment upon reproduction of line noises which are intruded to the power supply lines or induced noises onto the telecommunication lines.
-
product
Patient Simulators
Patient Simulators - also known as physiological simulators are essential tools for biomedical personals to accurately test and verify the performance of patient monitoring systems such as cardiac monitors, ECG machines. It simulates physiological parameters such as ECG, arrhythmia waveforms, blood pressure, respiration, temperature.
-
product
PXI Strain Gauge Simulators & Pressure Transducer Simulators
We offer simulation modules for Strain Gauge Simulation – used in mechanical systems to measure the tension or compression of structural components. These modules may also be used to simulate Wheatstone Bridge Pressure Sensors/Transducers. Simulation requires extremely fine setting resolution with high accuracy and temperature stability.
-
product
Simulation and Model-Based Design
Simulink
Simulink is a block diagram environment for multidomain simulation and Model-Based Design. It supports system-level design, simulation, automatic code generation, and continuous test and verification of embedded systems. Simulink provides a graphical editor, customizable block libraries, and solvers for modeling and simulating dynamic systems. It is integrated with MATLAB, enabling you to incorporate MATLAB algorithms into models and export simulation results to MATLAB for further analysis.
-
product
ARINC 429 Test & Simulation Interface for PCI Express
PCIe-C429X
Avionics Interface Technologies
16, 32, or 64 ARINC 429 Channels (up to 32 Tx & 32 Rx) - Programmable Tx channel output amplitude - Programmable High/Low Speed Operation - Eight (8) Discrete I/O (Four (4) inputs, and four (4) outputs) - Concurrent operation of all Tx/Rx Channels at high data rates - Full error injection and detection - Data capture filtering, 100% bus recording, and physical bus replay - Rate-oriented Label Transmission - Label Selective Trigger for Capture/Filtering - IRIG-B time code encoder/decoder with free-wheeling mode - Application Interface supporting C/C++, C# and VB.NET Development - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
product
1, 2, 4 Or 8 Stream MIL-STD-1553Test And Simulation Module For VME (6U)
AVC1553-x
MIL-STD-1553 Test and Simulation module for VME (6U) with 1, 2, 4 or 8 dual redundant channels.Integrated modular solution by using the AMCX1553-x PMC cards installed on AIM’s AVC-2 Generic VME64x (6U) Carrier card.
-
product
Circuit Simulation Software
Proteus Virtual System Modelling (VSM) blends mixed-mode SPICE simulation with world leading fast microcontroller simulation. It enables rapid prototyping of both hardware and firmware designs, in software! Design, Test and Debug your embedded projects in the Proteus electronic circuit simulator before a physical prototype is ordered. Agile development for the embedded systems workflow.
-
product
Simulator / Analyzer / Tester PCI BUS Interface Card
CIC301 - MIL-STD-1553
The CIC301 is a full-featured, high performance, Dual Redundant MIL-STD-1553 A/B serial bus Simulator Analyzer Tester designed as a plug in card for PCI backplane. The CIC301 includes full error injection and can operate in independent or simultaneous mode as a Bus Controller, multiple simulated Remote Terminals and full/selective Monitor. Its data structure can be changed on the fly without interrupting the processor for real time operation. The active monitor stores, time tag and annotates bus traffic with the message type and any detected errors. Stored words are annotated with a break down of the word error.
-
product
Solar Simulator
Sun 3000 Class AAA
The Abet Gen II optical design, patent pending, dramatically increases the percentage of photons reaching the work plane.All electronics are packaged in the lamp house – no clutter of high power cables to deal with. Photofeedback and digital shutter timer are included.Standard maintenance, lamp or filter replacement, does not require any tools. Locking indicator dials on all the system controls provide for a reproducible and stable setup. A built-in beam imaging accessory assists in system alignment.
-
product
PXI/PXIe LVDT/RVDT/High Speed Resolver Simulator Module, 4-Banks
43-670-301-AABBCC
The 41-670-301 (PXI) and 43-670-301 (PXIe) are ideal for the simulation of variable differential transformers (VDT), both linear (LVDT) and rotary (RVDT) types, as well as resolvers with high speed simulation up to 130krpm rotation. They have four banks, each capable of simulating the output of a single 5 or 6-wire VDT or resolver, or dual 4-wire utilizing a shared excitation signal. This allows the module to simulate up to 4 channels of 5 or 6-wire or 8 channels of 4-wire.
-
product
PXI Automotive Switch Simulator Modules
Pickering's Switch Simulator Modules are designed for automotive test applications. These modules simulate the operation of automotive switches where dirty contacts or leaking current can be expected from switch contamination. They allow automotive I/O devices to be tested for correct operation under adverse conditions.
-
product
Damped Oscillatory Wave Simulators
Suzhou 3ctest Electronic Co.,Ltd.
Damped oscillatory wave test system for new energy can produce repeatable transient on HV or medium voltage power cord, control line and signal line. It can meet the requirements of CE and CCC certificate. With internal three-phase five-wire high power CDN DOPN 69100T, it can conduct new energy test and high power load test with good reliability, stable performance and easy operation.
-
product
Single Or Dual Stream MIL-STD-1553A/BTest And Simulation Module For Standard Ethernet
ANET1553-x
The ANET1553-x is a member of AIM’s new line of Ethernet based modules for analysing, simulating, monitoring and testing MIL-STD-1553A/B databuses. For wireless applications, an ANET compatible USB Wifi dongle is optionally available. The capability to execute Python scripts in the ANET is a standard feature. For applications with multiple ANET devices AIM offers the ADock ANET Docking Station to host up to 4 ANET modules.
-
product
Test Hardware
TTPSimulate XMC/PCIe
TTPSimulate is a high-performance test system which enables the simulation of a networked TTP system in real-time. It allows full hardware in the loop verification of a TTP unit. There are two form factors available for this product – PCIe and XMC card format. Both cards can act as four independent TTP nodes and have an IRIG-B interface for time-stamping.
-
product
Power Amplifer AURORA Digital Interface For Simulator Application
PAV DIA01
PAV DIA01 is the optional accessory unit and Aurora digital interface for PONOVO’s power amplifiers which could convert the analog input signal into digital signal, supporting communication between power amplifier and simulators via AURORA protocol.
