Bit Error Rate Testers
Bit Error Rate Testers measure data integrity and express the ratio of received bits that are in error relative to the amount of bits received. Also known as: BERT
See Also: BER Testers, BERT
-
Product
LED Tester Software
Lumeresoft
-
Evolusys Technologies Sdn. Bhd.
At the heart of the software design philosophy is the ease to create test recipe amidst the dynamic range of LED packages design & test requirements. Whether it is a single die LED, multiple die LEDs, Chip-On-Board (COB) substrate, etc. the same software can be used off-the-shelf without any special customization.
-
Product
Dynamic Wettability Tester
6200TN
-
This is a dynamic wettability tester that uses a high-performance electronic balance to evaluate temporal changes in buoyancy and wetting (contact angle) that are successively received when various solid pieces and powder samples are immersed in liquid. Information such as dynamic and static contact angles, surface tension, and density can be obtained, and it supports various sample forms such as flat plates, fibers, and powders
-
Product
Clamping Voltage Tester
MIG0603CLV1
-
The MIG0603CLV1 is a generator for testing varistors. It has circuits with three different source impedances and up to 11 different measurement ranges. The instrument is used to perform varistor clamping voltage tests on up to 1000 V varistor types. The test impulse is a 8/20µs current waveform up to 200A which is maintained over the entire load range.
-
Product
Login Digital Epstein Tester Model
Model EP400
-
Digital Epstein Tester EP-400 is designed to measure AC magnetic properties of flat rolled magnetic materials at high frequency by using Watt-meter, Ammeter, Voltmeter and Source. Epstein bridge test method is a fundamental method for evaluating the magnetic performance of flat-rolled magnetic materials in either sheared or stress relief annealed condition. This test method is suitable for design, specification acceptance, service evaluation, and research and development.
-
Product
Roughness Testers
-
Roughness is an important parameter when trying to find out whether a surface is suitable for a certain purpose. Rough surfaces often wear out more quickly than smoother surfaces. Rougher surfaces are normally more vulnerable to corrosion and cracks, but they can also aid in adhesion. A roughness tester is used to quickly and accurately determine the surface texture or surface roughness of a material. A roughness tester shows the measured roughness depth (Rz) as well as the mean roughness value (Ra) in micrometers or microns (µm). Measuring the roughness of a surface involves applying a roughness filter. Different international standards and surface texture or surface finish specifications recommend the use of different roughness filters. For example, a Gaussian filter often is recommended in ISO standards.
-
Product
PE-, Insulation Resistance, HV- and Function Tester
GLP1-g
-
GLP1-g testers are ideally suited for use in production, laboratory, test field, quality management, automation and many more applications. Thanks to the individual combination of functions you are able to reach your aims quickly, reliably and cost-effectively.
-
Product
Ethernet/LXI generatorNETBOX 16 Bit Arbitrary Waveform Generator - up to 40 MS/s on 24 Channels
DN6.653-24
Arbitrary Waveform Generator
The generatorNETBOX DN6.65x arbitrary waveform generators (AWG) is a general purpose multi-channel AWG with outstanding dynamic performance. The series includes LXI units with either up to 48 synchronous channels. The large onboard memory can be segmented to replay different waveform sequences.
-
Product
Compression Testers
-
Dedicated compression testers offer low footprint test systems. Lever operated systems allows for quick and repeatable compression testing. The wheel operated system allows for more precision with hand wheel operation. The motorized compression tester allows for the most control and the highest degree of repeatability with the ability to set a constant test speed.
-
Product
Insulation and Continuity Tester
MIT2500
-
The MIT2500 insulation and continuity tester has been designed for motor and cable testing, specialist applications and electrical testing applications, where operation voltages exceed 1000 V and higher insulation test voltages are needed. The MIT2500 offers both fixed range voltages of 50 V, 100V, 250 V, 500 V, 1000 V and 2500 V, as well as a variable range that allows any voltage between 50 V and 2500 V to be "dialled in". This is supported by the new test voltage feedback control, which maintains the output test voltage to within 2% of the selected range, even when under test.
-
Product
Installation Safety Tester
Eurotest EASI
-
EurotestEASI is the first member of a new line of Metrel's installation safety testers. Lightweight design and small dimensions make it ideal for prolonged use over a working day.
-
Product
PCIe 16 Bit Arbitrary Waveform Generator - up to 40 MS/s on 1 Channel
M2P.6530-X4
Arbitrary Waveform Generator
The M2p.65xx series offers different versions of arbitrary waveform generators for PCI Express with a maximum output rate of 125 MS/s. These boards allow to generate freely definable waveforms on several channels synchronously. With one of the synchronization options the setup of synchronous multi channel systems is possible as well as the combination of arbitrary waveform generator with digitizers of the M2p product family. The 512 MSample on-board memory can be used as arbitrary waveform storage or as a FIFO buffer continuously stream data via the PCIe interface. Importantly, the high-resolution 16-bit DACs deliver four times the resolution than AWGs using older 14-bit technology.
-
Product
LED View Angle Tester
-
360°rotate perspective die scanning.0.36° as the smallest test step unit.Conjunction with LED tester for electrical and optical parts test.Test data collection and perspective diagram drawing.Support 4 sets of probe socket (standard equipment with 2 sets of probe sockets)Clip structure. Easy for die positioning.
-
Product
Buchholz Hardness Tester
3095
-
Measuring a coating’s hardness using the indentation method, the Elcometer 3095 Buchholz Hardness Tester consists of a bevelled disc indenting tool that is fitted into a stainless steel block exerting a constant test load of 500g (17.6oz).
-
Product
ICT Tester
-
Adapter design, assembly and validation for Agilent, Keysight, HP, Checksum, Spea. Preparing and debugging ICT scripts. ISP Programming Integration. Integration of edge scan testing, Jest testing, digital testing, semi-functional testing, IC programming, FINN probes, and more
-
Product
Multifunction Installation Tester
COMBI519
-
COMBI519 carries out tests on electric systems in compliance with IEC/EN 61557-1 and therefore measurements of continuity of the protection cable, insulation resistance (with calculation of PI and DAR), overall earth resistance, RCDs type B, A and AC tripping time and current, line / fault impedance with calculation of prospective short circuit / fault current, phase sequence and conformity.
-
Product
Gold Purity Tester
PRO‑ALLOY
-
The Easy Way To Test Gold & Platinum Jewelry. Measure the purity of rings, chains, watches and more… Instant gold karat reading • Fast and accurate • Non-destructive.
-
Product
High-Low Circuit Tester
29500
-
The low-side checks AC and DC current up to 28 volts with power on. The high-side checks spark plug wires without piercing. Complete with insulated clip.
-
Product
Withstand Voltage Tester
2672AM
-
Shenzhen Chuangxin Instruments Co., Ltd.
Withstand Voltage Tester is used to measure the dielectric (withstand voltage) strength, which can be intuitive, accurate and fast tested the electrical safety performance indicators of the object, such as the breakdown voltage, leakage current etc. And Withstand Voltage Tester can be used as a high voltage source to test performance of the components and whole machine.
-
Product
Automated Filter Tester
8127
-
The Automated Filter Tester 8127 is designed to comply with commercial respirator standards around the globe and has a proven track record of durability, reliability, and minimal maintenance, meeting the demanding requirements of manufacturing and quality control environments. Whether you are looking for a stand-alone tester to check a few filters per day or need to integrate your tester in an automated, high volume production line, CERTITEST AFT’s are up to the challenge
-
Product
Rotary Switch Life Tester
CX-1
-
Shenzhen Chuangxin Instruments Co., Ltd.
1: The CX-1 Rotary Switch Life Tester is strictly designed according to IEC60669-1, IEC61058-1, GB15092-1-2003 and GB15092.1 Standard. It's mainly used to test the service life of household and similar switch equipment products. 2: This rotary switch life tester connected to the power load cabinet and conduct electrical life test, normal operation and breaking capacity test of the rotary switch. 3: The rotary switch life tester is mainly used to test the all kinds switch
-
Product
Water Vapor Absorption Tester
DRK854A
-
Shandong Drick Instruments Co., Ltd.
Used to test the water vapor absorption performance of the sample.
-
Product
Smart SMD Testers
-
Precision Mastech Enterprises Co.
Compact, battery-operated, tweezer-like electronic tools designed for quickly measuring, identifying, and testing Surface Mount Device (SMD) components such as resistors, capacitors, and diodes.
-
Product
Lead Acid Intelligent Battery Tester
612
-
This digital battery tester is designed for testing 6V and 12V standby SLA, cyclic GEL and car FLOODED batteries. Simple in operation, the ACT 612 simulates a full 20 hour (C20) discharge test in seconds and displays the DC Voltage results and Ah capacity available.
-
Product
PXI Potentiometer Module 9x8 Bit, 0 Ohm to 256 Ohm
40-296-121-9/8
Programmable Resistor Module
The 40-295 is a Programmable Resistor module with up to 18 channels of 8-bit resolution resistor chains in a single 3U PXI module. The flexible architecture allows these modules to also be supplied as 12, 16 or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count.
-
Product
Penetration-Resistant Insert Flexing Tester
UI-FT05
-
Penetration-Resistant Insert Flexing Tester, also named as Steel Midsole Flexing Tester, is used to test penetration resistant inserts flexing resistance. As described in EN 12568, ISO 20344, the inserts shall exhibit no visible signs of cracking, disintegration or delamination after having been subjected to 1 *106 (one million) flexion cycles.
-
Product
Energized Tester
ALL-SAFE PRO
-
Conduct safe, easy and accurate ESA testing in only 60 seconds with the ALL-SAFE PRO® motor connection box. The ALL-SAFE PRO® is a permanently installed connection accessory for the ATPOL III™ energized testing instrument. With this electric motor connection box, the ATPOL III™ can perform tests easily with a quick disconnect.
-
Product
Heart Rate and Pulse Logger Sensor
NUL-208
-
This sensor can be used to monitor and compare pulse rates under various exercise and rest conditions. Additionally, it can show changes of blood volume/flow in the finger or ear lobe with time.The sensor has two modes of operation: measuring the BPM (Beats per Minute) of the heart rate or displaying the analog arbitrary value of the measured signal.
-
Product
AC /DC Withstand Voltage Tester 5KV/100mA
2672C
-
Shenzhen Chuangxin Instruments Co., Ltd.
*High voltage, large current, high accuracy.*Leakage current, testing time, continuous arbitrarily, well-adapted.*Synchronized display measuring value( time, voltage and current).*Can choose manual or remote control test*High voltage breakdown protection, sound and light alarm, safe and reliable *Easy operation, suitable for use in production line*DC output can test small capacitance, high-voltage silicon stack, reverse voltage of transistors
-
Product
Micromotor Tester
-
Shanghai Aoboor Electric Co., Ltd.
Applicable to no-load test of DC micromotors.
-
Product
110-460V AC/DC 4-way Circuit Tester
1962
-
Peaceful Thriving Enterprise Co Ltd
*With UL and cUL Approval.*Bright neon AC/DC indicator.*Unique features with convenient pocket up.*Check voltage on 110V, 220V, 277V and 460V AC/DC.*Individual indicator for each voltage range assures reliability.*Reinforced casing and twin flexible test leads store in housing.
