EMMC
-
Product
EMBEDDED MMC (EMMC)
SD 3.0 / eMMC 4.51 IP Family
-
The eMMC Host IP is an RTL design in Verilog that implements an MMC / eMMC host controller in an ASIC or FPGA. The core includes RTL code, test scripts and a test environment for full simulation verifications. The Arasan MMC / eMMC Host IP Core has been widely used in different MMC applications by major semiconductor vendors with proven silicon.
-
-
Product
EMMC
-
Device driver for controlling MultimediaCard using MultimediaCard Interface (MMCIF) built-in the MCU
-
Product
Qseven V2.0 SoM With IMX6 Quad/DualLite 800 MHz (Industrial) SoC, 1GB RAM, 4GB EMMC, GbE LAN, Audio And CAN
Q7M120
-
*Qseven v2.0 (70 x 70 mm)*Ultra low power consumption Cortex™-A9*2 CAN*24-bit TTL signal*LVDS/HDMI 1080P*10/100/1000 Mbps Ethernet*Linux 3.0.35/Android 4.3*Audio
-
Product
Qseven V2.0 SoM Evaluation Kit With Quad/DualLite 800 MHz (Industrial) SoC, 1GB Memory, 4GB EMMC, Gigabit Ethernet, Audio And CAN
Q7M120-120-EVK
-
*Ultra low power consumption Cortex™-A9*High flexibility Qseven v2.0 compliant design*2 CAN 2.0B*18/24-bit TTL LCD*LVDS/HDMI 1080P*10/100/1000 Mbps Ethernet*Linux3.0.35/Android4.3*Audio
-
Product
15.6" Full HD, 512MB, 8GB (EMMC), Seria Lx3, Dual Ethernet
WOP-315K
-
ARM9™ Cortex-A35 800MHz + 8GB for fast, smooth performance500+ protocols – connect any device, cut integration costs16MB non-volatile memory protects data from power lossFree HMINavi Designer – Serial/Ethernet/USB, no license neededUnlimited I/O/macros, up to 7,999 screensNo limitation on the internal I/Os points used for variety applicationReliable firmware setting from HMINavi software for 24/7 operationEasy to switch one application to different LCD sizes in secondsIP65 aluminum – tough and stylish
-
Product
IP Solution
eMMC 5.1
-
Demand for mobile content capacity and bandwidth for video, pictures and music is ever increasing. To address this demand in the next generation of smartphones, tablets, and portable devices, the eMMC 5.1 Specification from JEDEC, improves the current HS400 speeds operating at 3.2Gbps, with "command queuing" making the data transfers highly efficient by offloading the software overhead into the controller. eMMC 5.1 further improves the reliability of operation by utilizing an "enhanced strobe" at the PHY layer. The eMMC5.1 is backward compatible with the existing eMMC 4.51 and eMMC 5.0 Devices.
-
Product
Zynq Ultrascale+ MPSoC (ZU19/17/11EG) 3U-VPX Plug-in Module
iW-RainboW-G35V®
FPGA Module
AMD Xilinx’s ZU19/17/11EG Zynq Ultrascale+ MPSoC64bit, 8GB PS DDR4 RAM with ECC (Upgradable)Dual 64 bit, 8GB PL DDR4 RAM (Upgradable)8GB eMMC Flash (Upgradable)3U VPX Connectors based on ANSI/VITA 46.30 (P0+P1A & P1B+P2A)8 Optical transceivers through MT Ferrule Connector (P2B) based on VITA66.4
-
Product
LAN Router
ICR-2701
-
ICR-2700, EMEA, 2x Ethernet, USB, Metal, Without Accessories. 1.3 GB eMMC storage to host customer SW applications.
-
Product
SD Card
SD Card v.3.0 / eMMC v.4.51 IP Family
-
Designed for embedded applications that require high performance, small form factor, and high storage capacity, eMMC provides the support for embedded mass storage memory on embedded host systems. The eMMC protocol simplifies the access to NAND flash memories (such as MLC) to the host by hiding the functional differences among suppliers. Compliant to the latest JEDEC eMMC specifications, Arasan’s eMMC IP supports power-on-booting without the upper level software driver. The explicit sleep mode allows the host to instruct the controller to directly enter the sleep mode. The interface supports interface voltage of either 1.8V or 3.3V.
-
Product
Qseven® Standard Size Module With Intel® 6th Gen. Atom® X6000 Processors (Formerly Elkhart Lake)
Q7-EL
Computer on Module
The ADLINK Q7-EL is a Qseven module that supports Intel Atom® x6000 (x6425RE, x6414RE, x6413E) processors (formerly Elkhart Lake) with integrated Intel® UHD graphics and high-speed interfaces. With mechanical dimensions of 70mm width, 70mm length, and 2.3mm of overall height, Qseven ranks as one of the smallest COM standards currently available. Q7-EL modules support up 16GB LPDDR4 memory, up to 256GB eMMC storage and are also available with rugged operating temperature range and low power envelope, making them a perfect match for mission critical fanless edge computing applications that require safety and reliability at all times.
-
Product
Robust Din-rail Fanless Embedded System With RISC-based (iMX-287) Processor 4 COM, 2 CAN Bus And DIO
rBOX610
-
The rBOX610 din-rail fanless embedded system utilizes the low power RISC-based module (iMX-287) processor and is designed to withstand temperatures ranging from -40°C to +70°C for using in extreme operating environment and industrial automation applications. The rBOX610 box PC features 4 RS-232/422/485 serial ports, dual LANs, 4 digital input channels,4 digital output channels, 2 CAN bus and 1 eMMC onboard 4 GB & 1 x SDHC socket for storage expansion (easy to access) in a compact, IP40 protected, industrial-strength robust case. Two power paths input minimize the risk of data loss in the event of a single power failure. Its vertical din-rail form factor makes it easy to install the system in a small cabinet. Due to the RISC-based architecture, rBOX610 will not generate a lot of heat while being operated. The ready-to-run rBOX610 is specially designed for remote control/monitoring management applications like unmanned control room, industrial machine, automatic parking lot, traffic cabinet and more.
-
Product
LAN Router
ICR-2701A01-S1
-
ICR-2700-S1, EMEA, 2× ETH, USB, Metal, ACC EU. Security based on IEC 62443-4-2 level 1. 1.3 GB eMMC storage to host customer SW applications.
-
Product
Qseven V1.2 SoM With I.MX287 454 MHz (Industrial) SoC, 128MB Memory, 4GB EMMC, Gigabit Ethernet, Audio And CAN
Q7M100
-
*Ultra low power consumption ARM9*High flexibility Qseven v1.2 compliant design*2 CANBus 2.0B compliant ports*24-bit TTL LCD*Dual 10/100 Base-T Ethernet*Audio
-
Product
QSeven
ROM-7510
-
*TI Sitara AM5728 Dual core cortex-A15 1.5GHz high performance processor*Onboard DDR3 memory 2 GB and eMMC Flash 8 GB*Support 1 LVDS, 1 HDMI, 1 USB2.0 OTG, 4 USB2.0 HOST, 1 USB3.0,2 UART, 1 CAN, 1 SATA, 2 I2C, 1 I2S, 2 PCIE 1 lane,*Operating temperature 0 ~ 60 °C / -40 ~ 85 °C*Supports Linux Yocto
-
Product
19” Rackmount Data Collection System
DCS-211
Data Acquisition System
- Intel Atom® x5-E3930 processor- Up to 8x DI and 6x DO with two 2A relays- 3x M12 GbE, 1x RJ-45 GbE, 2x isolated RS232/422/485, 2x USB and one lockable HDMI port- Up to 3x PCI Express mini slots with one USIM card slot each- Storage: up to 64GB eMMC 5.0, 1x 2.5” SATA drive bay
-
Product
COM Express Type 10 Mini Module With Intel® Atom® X5 And X7 Processor
CEM310
-
The CEM310, a COM Express Type 10 Mini module, supports Intel® Atom® x5 and x7 processors (codename: Apollo Lake) in a board size of 84mm x 55mm. It has 8GB of DDR3L onboard memory and an optional 64GB eMMC memory. The Intel® Atom®-based COM Express Type 10 Mini module comes with a variety of I/O and expansion options including four PCIe x1 lanes, one Gigabit LAN port with Intel® i210IT Ethernet controller, two USB 3.0, eight USB 2.0, two SATA-600, four digital I/O channels, HD Codec audio, one DDI, one LVDS, one LPC, one SPI, two serial TX/RX and one I2C to meet customer requirements. Aside from the rich I/O options, the CEM310 has a wide voltage input range of 4.75V to 20V to meet the varying voltage input requirements for automotive or transportation applications. In addition, it supports an extended operating temperature range from -20ºC to +70ºC or optional -40ºC to +85ºC to ensure stable and reliable operation in harsh environments. The CEM310 supports watchdog timer, hardware monitoring functions, SMBus as well as smart battery (optional).
-
Product
Robust RISC-based DIN-rail Fanless Embedded System With I.MX 6UL Processor, DIO (2-in/2-out), 4 AI Channels (16-bit, 250 KS/s, 0 - 20mA, ±20mA) And 2 PCIe Mini Card Slots
IRU152-I
-
*RISC-based (i.MX 6UltraLite) processor 528 MHz*512MB DDR3 SDRAM onboard*8GB eMMC flash onboard*2 PCI Express Mini Card slots (Wi-Fi, 3G/4G or LoRa)*4 isolated analog input channels (16-bit, 250 kS/s, 0 - *20mA, ±20mA)*1 isolated COM port*1 isolated DIO (2-in/2-out)*Embedded Linux operating system (Yocto)*Wide operating temperature range from -40°C to +70°C*Supports LabVIEW versions later than 2016*Supports OPC UA
-
Product
Automated Programmer Superpro Sb05
-
※ Four Pick & Place nozzles, Eight socket pressing actuators and 2 tape feeders※ High throughput up to 2400UPH※ Embeded with eight ultra-high speed programmers SuperPro / 7500, each with up to 4 sockets, totally 32 sockets. Throughput 60 times higher than SuperPro / SB01 for eMMC devices※ Supports over 80,000 devices from over 300 IC manufacturers※ Supports tray, tape and tube input and output. Supports laser and ink marking※ Short change-over time※ Intelligent s/w cuts learning curve and setup time, makes task management an easy job※ Compact sizeHigh throughput：4 nozzles, 8 independent socket pressing actuators and 2 tape feeders. Up to 2400 UPH for devices with programming time less than 50 sec. Throughput 0.6 to 60 times higher than SuperPro/SB01, especially higher for large capacity devices like eMMC, NAND /NOR FLASH,SPI FLASH. Suitable for both small and large capacity devices. Prog. Time (S) 50 60 120 180 240 300 UPH (unit per hours) 1600 1600 840 560 420 336 Accurate positioning：Equipped with high performance servo system, precise CCD cameras and vision algorithm for device alignment and sockets / pick & place spots positioning.High performance programmers： 8 ultra-high speed universal gang programmers SuperPro/7500 resident. Each with up to 4 sockets, totally up to 32 sockets in the system. Supports up to 100,000 devices from over 300 IC manufacturers and growing.Varied I/O devices：Supports tray, tape and tube input and output. Supports laser and ink marking. Supports packing conversion and can work as a packing conversion machine alone.Short change-over time：I/O devices and socket adaptor are easy to be changed when programming task need to be changed. Socket positioning can be performed automatically. Projects can be loaded automatically with barcode scanning.Powerful and intelligent software：Setup data saved for next operation, log file and statistic reports for quality and yield traceability, flexible sockets prohibition strategy promises high yield rate for unattended operation, graphical user interface cuts learning curve, prevents chip over-lapping by socket checking before chip placing.Remote Control：Remote project loading, quality monitoring, volume control, file security.
-
Product
4G Router
ICR-2734A02
Router
ICR-2700, EMEA, 2× ETH, USB, Metal, UK Power supply LTE Cat.4 with 3G/2G fallback. 1.3 GB eMMC storage to host customer SW applications 2× SIM with cover, eSIM ready.
-
Product
Fanless Edge AI System With NVIDIA® JETSON™ TX2 Series SoM, 1 HDMI, 2 GbE LAN, 2 USB, 2 COM Or 2 CAN And 12 Or 24 VDC
AIE500-901-FL
-
The AIE500-901-FL is an advanced Artificial Intelligence embedded system for edge AI computing and deep learning applications. The high-performance embedded system employs an NVIDIA Jetson™ TX2 module which has a powerful 64-bit ARM® A57 processor; NVIDIA® Pascal™ GPU with 256 CUDA cores; and 8GB of 128-bit LPDDR4 memory. To withstand the rigors of day-to-day operation, the AIE500-901-FL has an extended operating temperature range of -30°C to +60°C and vibration of up to 3 Grms with its strong construction. This fanless Artificial Intelligence edge system is dedicated to achieving operational excellence, efficiency, reliability in smart manufacturing and intelligent edge applications. The edge computing device provides solutions as Edge AI embedded system, specifically designed for video analysis, object classification, computer vision, quality control and more. Under the ultra-compact enclosure design, the AIE500-901-FL comes with 32GB eMMC onboard and is equipped with one M.2 Key M 2280 SSD slot with PCIe and SATA signal and one Micro SD slot for massive data processing and AI applications. Besides, this reliable embedded system has one full-size PCI Express Mini Card slot and one SIM slot for 3G/4G, GPS, Wi-Fi and Bluetooth connections.
-
Product
4G Router
ICR-2834GP
Router
ICR-2800, EMEA, 2x Ethernet, 2× RS232/RS485, USB, GPS, Plastic, Without Accessories LTE Cat.4 with 3G/2G fallback. GNSS receiver 1.3 GB eMMC storage to host customer SW applications 2× SIM with cover, eSIM ready.
-
Product
LAN Router
ICR-2701A01
Router
ICR-2700, EMEA, 2× ETH, USB, Metal, EU Power Supply. 1.3 GB eMMC storage to host customer SW applications.
-
Product
Industrial Communication Gateway With TI Cortex A9, 2 LAN, 2 COM & 2 CAN
ECU-1252
-
TI Cortex A9 600MHz CPUDDR3L 2GB RAM16GB eMMC for system storage1 x Micro-SD Slot2 x CAN port2 x RS-232/485 isolated serial ports2 x 1000 Base-T Ethernet ports1 x Mini-PCIe for WIFI/Cellular/4GSupport web service for remotely on-line monitoring
-
Product
Digital Signage Player With Intel® Pentium® Processor N4200 & Celeron® Processor N3350, DisplayPort++, HDMI, 2 GbE LAN And 4 USB
DSP300-318
-
The DSP300-318 is powered by the onboard Intel® Pentium® processor N4200 and Celeron® processor N3350 (code name: Apollo Lake). It can deliver dazzling visual images and video advertising in 4K resolution. Measuring only 20 mm in thickness, the ultra slim DSP300-318 is sleek enough to fit in a small area behind signage displays and its fanless and cable free design enables easy installation without any environment limitation. The super slim DSP300-318 is designed to be fanless and cableless, which ensures solid reliability and easy maintenance. It supports HDMI and Dual-Mode DisplayPort (DP++) outputs with support for dual displays. The system also has one M.2 Key E 2230 for Wi-Fi and Bluetooth modules, one M.2 Key B 3042 for 4G LTE and one SIM card slots for 3.5G radio connectivity. Additionally, one M.2 Key M 2280 and one optional 64GB eMMC 5.0 are available for storage. The Intel® Apollo Lake-based DSP300-318 offers a cost-effective, compact yet powerful computing platform that allows plenty of digital signage solutions for advertising, brand promotion and digital menu board applications.
-
Product
4G Router
ICR-2734W
Router
ICR-2700, EMEA, 2x Ethernet, USB, Wi-Fi, Metal, Without Accessories LTE Cat.4 with 3G/2G fallback. 1.3 GB eMMC storage to host customer SW applications 2× SIM with cover, eSIM ready.
-
Product
4G Router
ICR-2834GA01-S1
Router
ICR-2800-S1, EMEA, 2× Ethernet, 2× RS232/RS485, USB, GPS, Metal, EU ACC LTE Cat.4 with 3G/2G fallback. Security based on IEC 62443-4-2 level 1 GNSS receiver 1.3 GB eMMC storage to host customer SW applications 2× SIM with cover, eSIM ready.
-
Product
4G Router
ICR-2734WA01-S1
Router
ICR-2700-S1, EMEA, 2× ETH, USB, WiFi, Metal, EU Power Supply LTE Cat.4 with 3G/2G fallback. Security based on IEC 62443-4-2 level 1, 1.3 GB eMMC storage to host customer SW applications 2× SIM with cover, eSIM ready.
-
Product
[Yocto/Android] 21.5" Touch Panel Computer With ARM Cortex™-A53 Processor
TPC-121W
-
arm SystemReady IR certifiedNXP® ARM® Cortex™-A53 i.MX 8M Mini quad-core processor16:9 LCD with multi-touch P-CAP and true-flat IP66-rated front panelUp to 4 GB DDR4 RAM and 16 GB eMMC storage onboard1 mb FRAM backup memory for unexpected power interruptions2 x Serial port with 120Ω termination resistor that one supports the CAN 2.0B protocol and offers a programmable bit rate of up to 1 Mb/secEmbedded browser and for rapid Web App developmentSupports Linux Yocto and AndroidCompatible with VESA and panel mounting
-
Product
SD Host Tester / SD / EMMC Analyzer / SD Card Tester
SGDK330B (SD / eMMC analyzer)
-
SGDK330B (SD / eMMC Analyzer) is a product that has the functions of SD Analyzer (SD Analyzer) and eMMC Analyzer (eMMC Analyzer).
