Protocol
A standard way of controlling hardware and/or software that enables connection, communication and data transfer.
See Also: NTCIP, Communication Protocol
-
Product
Infiniium V-Series Oscilloscope: 8 GHz, 4 Analog Channels
DSOV084A
Oscilloscope
8 GHz analog bandwidth (upgradable)4 analog channels Capture a longer signal trace with up to 80 GSa/s sample rate and 2 Gpts of acquisition memory Get the best signal integrity with low noise floor (1.04 mVrms at 50 mV/div) and lowest jitter measurement floor (100 fs)See better measurement accuracy with ENOB values in excess of 5.5 and a SFDR exceeding 50 dBC Improve your testing with the broadest range of jitter, trigger, analysis and protocol tools (featuring Precision Probe)
-
Product
Vehicle Presence and Data Collection Sensor
TrafiCam x-stream
-
TrafiCam x-stream combines a CMOS camera and video detector in one unit. TrafiCam x-stream sensors detect and monitor moving and stationary vehicles at signalized intersections and collect traffic data at intersections or interurban roads. Via detection outputs or via IP protocol, vehicle presence information is transmitted to the traffic controller so that signal timing can be adjusted dynamically. TrafiCam x-stream offers streaming video at full frame rate, to be used for traffic monitoring in a control room.
-
Product
Beagle USB 480 Protocol Analyzer
TP320510
-
The Beagle™ USB 480 Protocol Analyzer is a low cost, non-intrusive High-speed USB 2.0 bus monitor that includes real-time USB class-level decoding.
-
Product
Bus Analyzer / Exerciser
VME850P0
-
The VME850P0 analyzer is an optional plug on module for the VME850 analyzer that adds analyzer and exerciser functions to the VME850 analyzer for the P0 connector. This module allows the user to monitor and stimulate the A, B, C, D and E rows of the 95 pin P0 connector. Although the VME850P0 analyzer is in a PMC form factor it is not compatible with the PMC protocols and signaling. The signaling levels on the P0 connector must be less then 5V in order to prevent damage of the analyzer.
-
Product
GPIB-RS485/RS422 GPIB Instrument Control Device
779733-02
GPIB Controller
Serial, RS485/RS422 GPIB Instrument Control Device - The GPIB‑RS485 is an IEEE 488 controller device for PCs with RS485 or RS422 ports. You can use this device to integrate an instrument into your system using GPIB. This device transforms a computer with an RS485 or RS422 serial port into a talker, listener, or controller on the GPIB bus. It can also interface RS485 and RS422 instruments and peripherals to the GPIB bus. It can implement the physical and electrical specifications of the IEEE 488, RS485, and RS422 standards, as well as interpret and execute high-level commands from the serial port, including serial‑to‑GPIB, and GPIB‑to‑serial protocol conversions. This device is IEEE 488.2 compatible. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
Product
Digital I/O Adapter Module For FlexRIO
Digital I/O Adapter
Digital I/O Adapter Modules for FlexRIO offer up to 54 channels of configurable digital I/O that can interface with single‐ended, differential, and serial signals at a variety of voltage levels. When combined with a large, user‐programmable FPGA, you can use these modules to solve a variety of challenges, from high‐speed communication with a device under test to emulating custom protocols in real time.
-
Product
PXIe Digital I/O: 28 LVDS Channels, 8 Trigger Channels
M5302A
Digital I/O Module
M5302A is a single-slot Digital IO PXIe module with 28 programmable LVDS channels and 8 single-ended channels. The LVDS channels can be used to communicate to the device under test or can be used to control other devices by emulating protocols such as Camera Link. The single-ended channels are suitable for event triggers or other general-purpose IO applications.
-
Product
Autonomous RTU
ADU-500
-
Infinite Industrial Informatics Lt
ADU-500 is an ultra low power, wireless RTU with data logging and alarming capabilities. The battery powered RTU incorporates three digital inputs, two analog inputs, one pulse counter input and multiple excitation options for powering measuring transducers. The device supports acquisition of up to 48 measurement channels, based on the popular SDI-12 communication protocol.
-
Product
FreeScale I.MX 6 DualLite Industrial Protocol Gateway
WISE-710
-
Freescale i.MX 6 Dual Lite A9 1GHzSupport MQTT, LWM2M client for cloud communicationEmbedded with Microsoft Azure certified security chipSupport Micro SD card & on-line firmware updateSupport DI wet contact & dry contact by switchSupport Node ID by softwareSupport data logger on Micro SD cardOperation System: Yocto 2.1/ Ubuntu 16.04Operation Temperature: -20~55°C
-
Product
Memory Products
-
The electronic systems we use today require some form of memory for data and software storage. As a leading supplier of high-quality memory products, we offer a broad portfolio of serial EEPROM, serial EERAM, parallel EEPROM, OTP EPROM, serial Flash, parallel Flash, serial SRAM, NVSRAM, and CryptoMemory® security ICs to meet your memory needs. We also offer the industry’s first commercially available serial memory controller for use in high-performance data center computing applications. Our extensive testing protocols have ensured industry-leading robustness and endurance along with best-in-class quality to provide you with reliable products, dependable technical support and a consistent supply of devices throughout your product’s lifecycle.
-
Product
USB Controlled Multi-Function DAQ For ATE Education And ATEasy Training
GT98901 Series
-
The GT98901 Demo board is a USB controlled, cost-effective, multi-function PCB assembly. The module is completely self-contained and includes an LCD display, measurement and stimulus resources, digital I/O, relays, and switches – all of which can be accessed and monitored via the USB port using a SCPI command set via a USBTMC interface which supports the USB488 protocol. Power for the board is provided via the USB interface, providing a totally self-contained assembly which can provide users with a simple yet complete vehicle that replicates many of the stimulus and measurement functions associated with ATE systems. When combined with Marvin Test Solutions' ATEasy® Test Executive and Test Development environment, the GT98901 is the ideal product for creating and supporting ATE training and education applications.
-
Product
Four And Two-Port Multi-Protocol RS-232/422/485 PCI Express Mini Cards
mPCIe-COM-4SM Family
-
The mPCIe-COM-4SM family of cards feature high performance 16C950-class UARTs. Available in 4-port and 2-port versions, each port is capable of communication speeds up to 921.6kbps in RS-232 (differential modes support speeds as high as 3Mbps) and has 128-byte deep transmit and receive FIFOs. Large FIFOs protect against data loss in multitasking operating systems, reduce CPU utilization, and improve data throughput, while reducing or eliminating inter-character or inter-packet pauses. The advanced integrated circuit with pre-scalar supports a wide variety of custom baud rates, and any rates not otherwise achievable can be supported via a custom factory-installed crystal oscillator (up to 10Mbps!).
-
Product
GPS NTP Time Server - SYNTIME
-
Signals & Systems India Private Limited
Your product description goes hGPS NTP Time Server (SYNTIME) for Network Time Synchronization is a highly accurate time server. It generates time protocols to synchronize NTP/SNTP clients (Simple Network Time Protocol)/PTP clients (Precision time protocol IEEE 1588) over the network and operates at a speed of 10/100/1000Mbps. The NTP server accepts the time and frequency signals from sources like GPS or GLONASS. It achieves nanosecond accuracy and the system clock operates at stratum 1 when synchronized with time sources. It is a sleek, rack-mountable unit that synchronizes and maintains equipment/device time and avoiding any time drifts due to local RTCs. NTP output from time server supports unicast, broadcast, and multicast methods based on selection and behaves like a reference clock for the network. Apart from time synchronization protocols, it supports MD5 (Security key), SNMP, SSH, HTTP (Configuration), TELNET, FTP, and SYSLOG. IP address of the LAN ports can be field configurable.
-
Product
PCI CONET Controller
A2818
-
The Mod. A2818 is a 32-bit 33 MHz PCI card, which allows the control, through a standard PC, of up to 8 CAEN Optical Slave Cards (CAEN VME Bridge or Digitizers). The communication protocols used are the CONET1 or the new CONET2 (A dedicated firmware for the desired protocol must be installed on the board).
-
Product
CSI & DSI Protocol Generator
Envision X84 CSI&DSI
-
With comprehensive support for MIPI CSI-2v2 and DSI-2 specifications, Teledyne LeCroy’s Envision X84 generator platform provides the industry’s most accurate and reliable generation of MIPI camera and display protocols for fast debug, analysis and problem solving. The Envision X84 exerciser is loaded with innovative features that help uncover elusive protocol errors and is the intelligent choice for any camera and display validation needs. Using the same hardware platform as the Envision X84 C/D-PHY protocol analyzer, the Envision X84 offers the most flexible solution for MIPI Camera and Display validation and debug.
-
Product
SCADA Communication
-
From a technical point of view, communication is the process of exchanging information between a transmitter and a receiver. To achieve this, the transmitter encodes a message and transmits it to the receiver. The receiver can only decode the message if it knows the protocol. The setup of the communication between A. Eberle IED's (Intelligent Electronic Device) and a SCADA system becomes more easy if all partners communicate in such a way that all queries regarding the protocol are clarified before or during the system design process (at latest before commissioning).
-
Product
Four And Two-Port Multi-Protocol RS-232/422/485 M.2 Cards
M.2-COM-4SM Family
-
The M.2-COM-4SM family of cards feature high performance 16C950-class UARTs. Available in 4-port and 2-port versions, each port is capable of communication speeds up to 921.6kbps in RS-232 (differential modes support speeds as high as 3Mbps) and has 128-byte deep transmit and receive FIFOs. Large FIFOs protect against data loss in multitasking operating systems, reduce CPU utilization, and improve data throughput, while reducing or eliminating inter-character or inter-packet pauses. The advanced integrated circuit with pre-scalar supports a wide variety of custom baud rates, and any rates not otherwise achievable can be supported via a custom factory-installed crystal oscillator (up to 10Mbps!).
-
Product
ATE For Data Communications Equipment
-
• Developed for DRS Codem Systems, Inc. to test the CTM-IP product line of the Multi-Interface Protocol Converter.• Manufacturing Test support for the CTM-IP chassis and Interface Modules. Functional test of signaling, protocol and software configurations for various communication interface configurations.• Regression Test support for Engineering Product Development. Configurable test sequencing allows engineer to select specific tests for execution, with the ability to exercise all combinations of data rates and interface configurations.
-
Product
DisplayPort v1.3 Protocol Analysis Probe
FS4500
-
The FuturePlus FS4500 DisplayPort Analysis Probe provides a mechanical, electrical and software interface to the DisplayPort bus, a digital display interface standard supported by the Video Electronics Standards Association (VESA). The FS4500 is used to design and debug computer motherboards, monitors, home theater systems, and silicon chips incorporating DisplayPort technology.
-
Product
Multifunction Field Calibrator & Communicator
MC6-Ex
-
The MC6-Ex is an intrinsically safe field calibrator and communicator. It is ATEX and IECEx certified and can be used in all hazardous zones / divisions. The MC6-Ex includes a field communicator for HART, FOUNDATION Fieldbus and Profibus protocols. Each calibrator is delivered with a traceable, accredited calibration certificate as a standard. t is a documenting, multifunction calibrator and communicator that offers calibration capabilities for pressure, temperature and various electrical signals.
-
Product
Modbus RTU Rs486/232/422
-
It provides client/server communication between devices connected to different types of buses or networks. Modbus-RTU (Remote Terminal Unit) means that the Modbus protocol is used on top of a serial line with an RS-232, RS-485 or similar physical interface.
-
Product
Databus-to-Network Interfaces
OBB2
Interface
The OBB2 is highly configurable and includes built-in standard peripherals (Ethernet, serial, and USB), along with four internal Cores that can be populated with a variety of databus protocols and discrete I/O modules. With the newest advanced set of MIL-STD-1553 and ARINC 429 modules, users can verify wave form compatibilities, test functions of bus shorts and opens, and—when combined with our CoPilot® software—perform lab, production and flight test verification and simulation right out of the box.
-
Product
GPIB-RS485/RS422 GPIB Instrument Control Device - Brazil 127-220VAC
779733-12
GPIB Controller
The GPIB‑RS485 is an IEEE 488 controller device for PCs with RS485 or RS422 ports. You can use this device to integrate an instrument into your system using GPIB. This device transforms a computer with an RS485 or RS422 serial port into a talker, listener, or controller on the GPIB bus. It can also interface RS485 and RS422 instruments and peripherals to the GPIB bus. It can implement the physical and electrical specifications of the IEEE 488, RS485, and RS422 standards, as well as interpret and execute high-level commands from the serial port, including serial‑to‑GPIB, and GPIB‑to‑serial protocol conversions. This device is IEEE 488.2 compatible. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
Product
Infiniium S-Series High-Definition Oscilloscope: 6 GHz, 4 Analog Channels
DSOS604A
Oscilloscope
6 GHz bandwidth (upgradable)4 analog channels Capture a longer signal trace with 20 GSa/s max sample rate and 100 Mpts/channel of standard memory Get superior signal integrity with system ENOB of 6.8 bits and 10-bit analog-to-digital converter (ADC)Gain increased usability with the multi-touch supported 15 inch capacitive touch screen and solid state drive for fast boot and reliability Improve your testing with a wide range of protocol, compliance, and analysis software
-
Product
AFDX ® / ARINC 664 Test And Simulation PCI Module
PCI-C664
-
*Supports IEEE 802.3 10/100/1000 Mbit / s full duplex Ethernet connections*Uses SFPs to support both electrical and optical interfaces*Half-size PCI / PCI-X modules*Simulates multiple AFDX® / ARINC 664 end systems*Standard Ethernet processes simultaneous with ARINC 664*Up to 128 output VLs and 512 input VLs*Upper layer protocol handling (ARINC 653, UDP, IP) managed onboard*DMA for high data rate applications*Windows XP / 7, Linux, and LabVIEW Real Time Drivers & APIs (others on request)*Easy to use tool for configuring AFDX® / ARINC 664 end systems (XML based)
-
Product
Remote I/O
-
ADLINK remote IO and serial communication cards are suitable for handling multiple digital signal types for IoT and other industrial applications such as facility monitoring, environmental monitoring, and industrial process control.Remote IO - NuDAM modules provide direct communication with various sensors, including performing signal conditioning, scaling, linearization and conversion to obtain temperature, pressure, flow, voltage, and current measurements. The new ND6100 series modules use Modbus/RTU remote data transmission protocols, providing customers with a comprehensive product portfolio. ADLINK's serial communication cards provide a PCI/PCIe interface and support RS-232 and CAN communication interfaces, allowing customers to choose the most suitable communication card for various automation equipment needs.
-
Product
Infiniium S-Series High-Definition Oscilloscope: 8 GHz, 4 Analog Channels
DSOS804A
Oscilloscope
8 GHz bandwidth4 analog channels Capture a longer signal trace with 20 GSa/s max sample rate and 100 Mpts/channel of standard memory Get superior signal integrity with system ENOB of 6.4 bits and 10-bit analog-to-digital converter (ADC)Gain increased usability with the multi-touch supported 15 inch capacitive touch screen and solid state drive for fast boot and reliability Improve your testing with a wide range of protocol, compliance, and analysis software
-
Product
1 Channel, MIL-STD-1553, Dual Redundant, Direct Coupled, Assisted Mode Capable (AMC)
FTD
-
MIL-STD-1553 is a military standard published by the United States Department of Defense that defines the mechanical, electrical, and functional characteristics of a serial data bus. It was originally designed for use with military avionics, but has also become commonly used in spacecraft On-Board-Data-Handling (OBDH) subsystems, both military and civil. It features a dual, redundant, balanced-line, physical layer; a (differential) network interface; time division multiplexing; half-duplex command/response protocol; and up to 31 remote terminals (devices).
-
Product
Packet Sniffer
EtherDetect
-
EtherDetect Packet Sniffer is an easy for use and award-winning packet sniffer and network protocol analyzer, which provides a connection-oriented view for analyzing packets more effectively. With the handy tool, all you need to do is to set up the filter, start capturing, and view connections, packets as well as data on the fly.
-
Product
Ethernet Protocol Analyzer
Investigator
-
Absolute Analysis Investigator features the most flexible, scalable and versatile instrument for protocol test and verification. The architecture is extensible to support multiple protocols and multiple test applications to meet the expanding requirements of various network topologies. CPRI, Serial RapidIO, Fiber Channel, Ethernet (10, 100, 1000, 10G), Serial FPDP, Custom military or secure protocols.
