Can bus
Controller Area Network
See Also: Serial, I2C, LIN, ExpressCard, Fieldbus, FireWire, RS-232, RS-485, PCI Express, Serial ATA, Serial Peripheral Interface, SMBus
-
Product
3-Ch 200 MHz A/D with DDC & 2-Ch 800 MHz D/A with DUC, Virtex-7 FPGA - XMC
Model 71721
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- Three 200 MHz 16-bit A/Ds- Three multiband DDCs (digital downconverters)- Two 800 MHz 16-bit D/As- One DUC (digital upconverter)- Multiboard programmable beamformer- 4 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multimodule synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x8- VITA 42.0 XMC compatible with switched fabric interfaces- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
MIL-STD-1553 Test & Simulation Interface for VME
VME-1553
-
Avionics Interface Technologies
Dual redundant, single, dual, or quad stream configurationsTransformer & Direct Bus Coupling - Concurrent Bus Controller, 31 Remote Terminals, & Bus Monitor operation - Full error injection and detection - Multi-level trigger for capture and filtering - IRIG-B time code encoder/decoder - Ten high voltage (up to 30V) programmable DIO lines - Real-Time recording and physical bus replay - ANSI Application interface supporting C, C++, C#, and .NET development - Device driver support: Windows, Linux, & VxWorks (others on request) - Designed for extended temperature operations - 64-bit VME Interface (VME master & slave capability) - Front Panel and Rear I/O (P2) Available
-
Product
Message Based Intelligent Interface Card
IIB-3910-VXI
-
The IIB-3910-VXI is message based intelligent interface card for dual redundant 3910 and 3838 applications. It gives full 3910 and 3838 test, simulation and bus analysis capability on the VXI bus, providing 3910, 3838 1553A, and 1553B variants in a single card. Each channel supports concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with passive Bus Monitor, and an independent Chronological Bus Monitor (CBM). Full error injection capability is provided in BC and RT modes, with full error detection in BC, RT, BM and CBM modes. The unit provides dual redundant prEN3715 compatible 3910 interface, with variable amplitude dual redundant 3838 interfaces. External trigger-in and trigger-out are provided, with both Primary and secondary bus coupling for direct and stub bus, with access to internal 1553 bus, on the front panel.
-
Product
VXI Register Interface Board
VXI-5524A
-
*VXI Register Interface mates with user's PCB to form a B or C-size module.* 48 Digital IO Lines - Three 16-bit registers set as latched outputs or gated inputs.* 16 line bi-directional expansion bus for driving external logic.* Digital IO and VXIbus lines are 3.3V logic levels and are 5 V tolerant for compatibility with 3.3V logic and 5V VXIbus signals.* User selectable 3.3 and 5 Vdc puliup voltage on the digital IO lines for sensing switches etc.* The VXI-5524A board is a complete VXI-1 Rev 1.4 and VXI-2 compliant register-based interface.* User configurable model number, manufacturer ID, version and serial numbers.* Two companion component boards available for prototyping IC or RF assemblies.* Companion hardware kits available for building 1, 2 or 3-slot wide modules.
-
Product
GPIB to Quad Serial Interface
Model 4896
-
* Provides four RS-232/RS-422/RS-485 Serial Channels.* High speed, 115.2 K baud channels include 60 K byte buffers.* > 600 K byte/sec. GPIB data transfer rate.* SCPI commands set serial configuration and GPIB address.* LCD display shows Bus activity, buffer status, serial interface signals and channel settings.* 1 U high rack mount kit mounts one or two 4896s * Includes US 115 VAC Power Adapter, Manual and Support CD.
-
Product
Printed Circuit Board
RISER-PCM-1
Printed Circuit Board
WINSYSTEMS’ RISER-PCM-1 boards are designed to provide extra space in a PC/104 stack. They are printed circuit boards (PCBs) with PC/104 mounting holes and bus connectors. They allow a board with either tall components or heat sinks to be placed in a stack of boards in a location other than only at the top. The additional separation is 0.60 inches using standard PC/104-type spacers.
-
Product
Hard Metric Eurocard Plugbord
8017
-
VECTOR Electronics and Technology, Inc.
3U x 160mm Eurocard size for 2mm Hard Metric connector. Pad-Per-Hole both sides.Pad and bus surfaces solder coated. Accepts cPCI 2mm J1 (25 row) & J2 (22 row) connectors on edge.
-
Product
VXI Chassis
Chassis
The first VXIbus specification was introduced to the test and measurement community in 1987 and was initially developed to provide a card-based instrumentation platform for applications that required high density and high performance. The platform continues to thrive today by leveraging off the original specifications which define the necessary physical (real estate/cooling) and electrical standards for demanding applications and has established itself as the ‘time-tested bus you can trust’ for requirements that must be supported in excess of ten-fifteen years.
-
Product
PCIe-8510, 2- or 4-Port, PCIe Vehicle Multi-Protocol Interface Device
785325-01
Interface
2- or 4-Port, PCIe Vehicle Multi-Protocol Interface Device—The PCIe‑8510 is a hardware-selectable controller area network (CAN) and/or local interconnect network (LIN) interface for developing applications with the NI‑XNET driver. The PCIe‑8510 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
Product
CAN/FlexRay/Differential Bus PCI Fault Insertion Switch - 8 Channel
50-200-008
Fault Insertion Unit
This PCI Fault Insertion card is designed to simulate common faults on two wire communication interfaces such as CAN Bus. This card supports 4 or 8-channels of two wire serial interfaces. Each channel can simulate an open fault in either or both wires, a short between both wires or a short to one of eight externally applied fault connections, such as a battery connection or ground, via four fault buses.
-
Product
CAN Logger
-
Reach Technologies' CAN Logger is a high performance, high channel count, DSP enabled, automotive bus data logger. The CAN Logger is ideal for capturing all or specific bus traffic for vehicles under test. The CAN Logger is also perfect for real-time monitoring of specific signals.
-
Product
Osprey /SX Co Processor
9775
-
Successor to Osprey 18B, EISA/ISA bus compatible, it occupies one PC slot. Writable control store FPGA implementation of PDP-11 architecture with 4 MBytes of tightly coupled, zero wait-state memory. Performance equivalent to DCJ11. Rapidly processed "virtual" I/O instructions makes this card ideal for Osprey/PC applications where all applicable I/O devices are emulated on the PC by Osprey software. Includes MS-DOS compatible support software. Windows/NT environment support available.
-
Product
Local Bus Master & Target Bridges
PCI 9052
-
The PCI 9052 PCI I/O Accelerator provides low cost connectivity for PCI slave designs. It is specifically targeted at easing the transition of existing ISA designs to the more feature rich and performance oriented PCI bus.
-
Product
GPIB-RS485/RS422 GPIB Instrument Control Device
779733-02
GPIB Controller
Serial, RS485/RS422 GPIB Instrument Control Device - The GPIB‑RS485 is an IEEE 488 controller device for PCs with RS485 or RS422 ports. You can use this device to integrate an instrument into your system using GPIB. This device transforms a computer with an RS485 or RS422 serial port into a talker, listener, or controller on the GPIB bus. It can also interface RS485 and RS422 instruments and peripherals to the GPIB bus. It can implement the physical and electrical specifications of the IEEE 488, RS485, and RS422 standards, as well as interpret and execute high-level commands from the serial port, including serial‑to‑GPIB, and GPIB‑to‑serial protocol conversions. This device is IEEE 488.2 compatible. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
Product
USB-8452, 3.3 MHz I2C, 50 MHz SPI I2C/SPI Interface Device
781964-02
Interface Module
The NI USB‑8452 is a master interface for connecting to and communicating with inter-integrated circuit (I2C) and serial peripheral interface (SPI) devices. With plug‑and‑play USB connectivity, the USB‑8452 is a bus-powered, portable solution to communicate with consumer electronics and integrated circuits. It also includes eight general-purpose digital I/O lines for a variety of applications, such as configuring the address of I2C devices, toggling LEDs, or strobing convert and data ready lines common to analog converter chips. You can physically place the USB‑8452 more closely than PCI interfaces to I2C/SPI devices, which reduces I2C bus length and minimizes noise problems. Additionally, the interface provides +5 V and GND to power circuits with no external power supply.
-
Product
Single 24x4 1-Pole High-Density PXI Matrix Module
40-520-402
Matrix Switch Module
The 40-520 family of high-density PXI matrices is available in 22 different configurations with up to 256 crosspoints. The choice of six bus widths (x16, x12, x8, x6, x4 and x2) enables competitively priced solutions using Pickering Electronics instrumentation quality reed relays. These relays offer very long life with good low-level switching performance and excellent contact resistance stability. Typical applications include signal routing in ATE and data acquisition systems.
-
Product
3U VME J1 Classic 10-slot With 70A M4 Power Bolts
50510-210-0000
-
3U VME Bus J1 Classic Backplane 10-slot, VITA, termination passive inboard, daisy chain automatic active, power connection 70A power bolts, I/O pins 13mm gold-plated, shroud (1P1) without latches
-
Product
MIL-STD-1553 Modules
-
> MIL-STD-1553B is the military specification defining a digital time division command/response multiplexed databus. The 1553 databus is a dual-redundant, bi-directional, Manchester II encoded databus with a high bit error reliability. All bus communications are controlled and initiated by a main bus controller. Remote terminal devices attached to the bus respond to controller commands. MIL-STD-1553B defines specifications for terminal device operation and coupling, word structure and format, messaging protocol and electrical characteristics.
-
Product
Dual-Band RF Tuner and 4-Ch 400 MHz A/D with Kintex UltraScale FPGA - 6U VPX
Model 58891
-
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Accepts RF signals from 925 MHz to 2175 MHz- Programmable LNA handles L-Band input signal levels from -50 dBm to + 10 dBm- Programmable analog downconverter provides IF or I+Q baseband signals at frequencies up to 123 MHz- Four 400 MHz 12-bit A/Ds digitize IF or I+Q signals synchronously- Four FPGA-based multiband DDCs (digital downconverters)- Two Xilinx® Kintex® UltraScale™ FPGA- 10 GB of DDR4 SDRAM- Sample clock synchronization to an external system reference- PCI Express interface (Gen. 1, 2 & 3) up to x8- Clock/sync bus for multimodule synchronization- Optional LVDS and gigabit serial connections for FPGA for custom I/O- Navigator BSP® for software development- Navigator FDK® for custom IP development- Spark® fully-integrated development system- Free lifetime applications support- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
M-Module Carrier for CompactPCI (3U)
i3002
-
The i3002 provides a high-performance CompactPCI bus gateway to the M-module interface. The i3002 has a 3U form factor. Two M-modules can be mounted on the i3002. The M-module interface of the i3002 complies with the M-module specification. The M-module interface feature A8, A24, D16 and D32 access types.
-
Product
STD Bus, Vectorbord Plugbord
4610-3
-
VECTOR Electronics and Technology, Inc.
56 Gold plated edge contacts (28 each side)on 0.125"(3.175mm) centers.Pad per hole and peripheral buses both sides.Row and column legends provided.
-
Product
STD, S-100 Bus Plugbord
-
VECTOR Electronics and Technology, Inc.
Card edge board for STD and S-100 bus specification card size and edge contacts on tabs. Available with different circuit patterns for prototyping applications.
-
Product
CompactPCI
cPCI4IP
-
The cPCI [CompactPCI] compatible cPCI4IP design adds 4 Industrypack compatible slots to your cPCI host. The cPCI4IP acts as an adapter, converter, carrier, or bridge between the cPCI bus and your IndustryPack hardware. The cPCI4IP is a 6U 4HP cPCI design with 4 IP slots.
-
Product
PXI / PXIe Chassis
-
PXI (PCI eXtensions for Instrumentation) is a PC-based bus platform for measurement and automation systems. PXI uses commercial PC-based PCI bus technology while combining rugged CompactPCI modular packaging, as well as key timing and synchronization features. While derived from cPCI, PXI adds the timing and synchronization features, among other things, that were not present in cPCI.
-
Product
Isolated Digital I/O Card
mPCIe-IDIO-8
-
The mPCIe-IDIO-8 consists of a type F1 PCI Express Mini Card (mPCIe) interface board that connects to a Mobile-ITX-sized, DB-37M Isolation Module via an included 9” cable. That module is designed to be easily panel-mounted in any application environment. It uses the high speed PCI Express bus to transfer digital data to and from the card. The digital I/O is compatible with 8255 PPI chips making it easy to program.
-
Product
USB-8451, 250 kHz I2C, 12 MHz SPI I2C/SPI Interface Device
779553-50
Interface Module
The NI USB‑8451 is a master interface for connecting to and communicating with inter-integrated circuit (I2C), System Management Bus (SMBus), and serial peripheral interface (SPI) devices. With plug‑and‑play USB connectivity, the USB‑8451 is a portable solution to communicate with consumer electronics and integrated circuits. It also includes eight general-purpose digital I/O lines for a variety of applications, such as configuring the address of I2C devices or toggling LEDs. The USB‑8451 can be physically located more closely to I2C/SPI devices than PCI interfaces, reducing I2C bus length and minimizing noise problems. Additionally, the interface provides +5 V and GND to power circuits with no external power supply.
-
Product
Hybrid Power Systems
-
UNIPOWER Hybrid Power Systems are designed to minimize power system life-cycle costs and carbon footprint. Power conversion components deliver leading efficiencies and maximum energy harvest from renewable resources using MPPT algorithms. A Hybrid Bus Architecture delivers available power from renewable resources supplemented by diesel generator or grid supply when necessary.
-
Product
MIL-STD-1553 A / B Test And Simulation VXIbus Module
VXI-1553
-
*1, 2, 4 or 8 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*Multi-level trigger for data acquisition and filtering*10 programmable, discrete I / O*IRIG-B timecode encoder / decoder with free-running mode*Real-time recording and physical bus playback*Supports: C, C ++, C # and .net*VISA based VXI Plug & Play driver*Optional twinax front end
-
Product
1100-Channel GSM Channelizer wih Quad A/D - 3U VPX
Model 52663
-
- Complete GSM channelizer with analog IF interface- Four 180 MHz 16-bit A/Ds- Two banks of 375 DDCs for upper GSM band- Two banks of 175 DDCs for lower GSM band- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- PCI Express Gen. 2 x4- 3U VPX form factor provides a compact, rugged platform- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
L-Band RF Tuner and 2-Channel 500 MHz A/D with Virtex-7 FPGA - 3U VPX
Model 52791
-
- Accepts RF Signals from 925 MHz to 2175 MHz- Programmable LNA handles L-Band input signal levels from -50 dBm to +10 dBm- Programmable analog downconverter provides IF or I+Q baseband signals at frequencies up to 123 MHz- Two 500 MHz 12-bit A/Ds digitize IF or I+Q signals synchronously; optional: 400 MHz 14-bit A/Ds- Two FPGA-based multiband digital downconverters- Xilinx Virtex-7 VX330T or VX690T FPGAs- 4 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- PCI Express (Gen. 1, 2 & 3) interface, up to x4- Clock/sync bus for multimodule synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
