Print Circuit Board
-
Product
PCIe Gen3 Full HD, High Speed, Compact Camera for Testing
CB019CG-LX-X8G3
-
Full HD, High speed, compact, fast camera for: Vehicle Impact, Airbag Deployment and Safety Restraints Testing, Digital Image Correlation (DIC), Projectile, Explosives, Ballistics, Combustion and Missile Launch Tracking, Fluid and Flow Visualization, Sports Broadcasting, Commercial Film, Television and Studio Production, Fluidics and Particle Image Velocimetry (PIV), Flat panel inspection (FPD), printed circuit board (PCB) examination and more.
-
Product
MECHANICAL TEST FIXTURE KITS
TX-MT-100 SERES
-
Test-X MT-100 Series mechanical kits are an inexpensive solution for testing smaller printed circuit boards and other devices.The MT-100 Series features a 1/2" thick FR4 probe plate and a 3/8" thick Lexan top plate. Precision alignment is assured through tooling holes in both the probe and top plates. Units are available with a 2-1/2" pan or an upper head assembly
-
Product
Test Fixture Kits
-
Our test fixture kits provide cost effective solutions to printed circuit board testing and other devices under test. Our modular kits are available in multiple sizes and configurations. They can easily be customized if our standard doesn’t meet your requirements. Removable side panels for ease of fabrication for I/O connections, switches or other hardware.
-
Product
Double Sided PCB
-
Double Sided PCBs (also known as Double-Sided Plated Thru or DSPT) circuits are the gateway to higher technology applications. They allow for closer (and perhaps more) routing traces by alternating between a top and bottom layer using vias. Today, double sided printed circuit board technology is perhaps the most popular type of PCB in the industry.
-
Product
Miniature 8-channel photon counter
id150 SERIES
-
Intended for large-volume OEM applications, the id150-1x8 is the only multichannel solid-state single photon detector on the market. It consists of a CMOS silicon chip packaged in a standard TO8-16pin header with a transparent window cap. The chip combines 8 in-line single photon avalanche diodes that can be accessed simultaneously for parallel processing. square in center-to-center A fast active quenching circuit is integrated within each pixel in order to operate each diode in photon counting regime. The chip is mounted on a printed circuit board on top of a single-stage thermoelectric cooler (TEC). A thermistor can be used to measure the temperature of the chip. Only two low power supplies of +5V and -25V are needed for operation in photon counting mode. The fast active quenching circuit leads to a dead time of less than 50ns per channel. An outstanding timing resolution of less than 60ps allows high accuracy measurements.
-
Product
FlexRIO Adapter Module Development Kit for Modular I/O
780711-01
Module
FlexRIO Adapter Module Development Kit for FlexRIO—The FlexRIO Adapter Module Development Kit (MDK) for Modular I/O enables you to choose the specific converters, buffers, connectors, and other components so that you can build the exact analog and digital I/O you need into a custom adapter module for FlexRIO. NI recommends that you have custom printed circuit board (PCB) design and hardware description language (HDL) code development experience to use the FlexRIO Adapter MDK for Modular I/O.
-
Product
Functional & ICT Tester
igentic® 621t
-
Growing demand for light emitting diode (LED) products and increasing testing complexity continue to challenge electronic printed circuit board (PCB) manufacturers. The igentic® 621t is a flexible PCB tester that ensures quality while increasing production. The tester can handle multiple PCB products and test for light measurements, resistance and push button or post detection, as required.
-
Product
Panel Mount With Fan Out For Connecting To A Printed Circuit Board
-
Panel Mount With Fan Out For Connecting To A Printed Circuit Board
-
Product
CAT-5 Video Drivers
-
Analog Devices provides designers with a robust portfolio of high speed triple, differential, and single-ended input to differential output CAT-5 video drivers. We designed the technology for the highest resolution component video signals, but it can be used for any type of analog signals or high speed data transmission over either Category 5 UTP cable or differential printed circuit board (PCB) transmission lines. Manufactured with our second generation XFCB bipolar process, the drivers have large signal bandwidths of 700 MHz, fast slew rate, and output amplitude and phase matching balanced to –60 dB at 50 MHz.
-
Product
Immunity Development System
-
Used for EMI suppression in printed circuit boards during the development phase. The developer can use the E1 set to quickly identify the causes of burst and ESD interference. This allows the developer to design suitable measures to solve the causes of the interference. It can also be used to test the effectiveness of the measures taken.
-
Product
Detector And FPA Testing
-
The FPA Test Set (FPATS) interface to the detectors under test (DUT’s) is via a custom pedestal plate which provides both a conductive heat path to both the individual DUT’s as well as the field of view limiting aperture plate. This custom pedestal plate protrudes through the customer provided DUT interface printed circuit board (PCB) and makes physical contact with the rear of the DUT packages and the aperture plate when the FPATS is in the closed position. The pedestal plate is mounted to the ambient source plate and its temperature is actively driven by this subsystem.
-
Product
PCI Express
-
PCI Express (PCIe) is a highly successful SerDes interface that is used in computing devices spanning a wide range of applications. Currently in its fourth generation with on-going roadmap development for a fifth generation, the PCIe interface is undergoing major technical advancements that require state-of-the-art development and validation tools. For example, Gen4 PCIe devices operate at 16 Gbps per lane and are expected to deliver very low bit error rate (BER) levels even over constrained and lossy transmission channels (e.g. printed circuit boards).
-
Product
2.5-inch IDE Disk Adapter
4946
-
The HDD is positioned midway such that the PMC component envelope is not violated. Furthermore, steel rails are attached to the printed circuit board, allowing for a secure, robust installation of the hard disk drive. This is a superior mechanical approach, compared with other printed circuit board-based solutions available on the market.
-
Product
Electrical Tester Grid Field
-
TCI can furnish grid spring probes for most Bare Board Electrical Testers in production at most Printed Circuit Board Manufactures. Look for your model of Bare Board Tester in the following list and call TCI for current price quotation.
-
Product
Extender
3690-12
-
VECTOR Electronics and Technology, Inc.
Contact fingers at the other end of extender card are gold plated provides low insertion force and positive contact with printed circuit boards. Receptacles have double row phosphor bronze contacts with high quality, long life mounted on top of the extender.
-
Product
75 Ohm SMB Connectors
-
Pasternack 75 Ohm SMB connector category includes dozens of part numbers, most are RoHS and REACH compliant. 75 Ohm SMB connector series in this category will terminate to coax, PCB (printed circuit board) or terminal. Our SMB 75 Ohm connectors are built to precise microwave and RF industry specifications. Pasternack 75 Ohm SMB connector products are built in jack or plug gender with 75 Ohm impedance. SMB connectors in 75 Ohm impedance are available in straight or right angle versions, as well as, bulkhead or mountless options. These 75 Ohm SMB connector designs include clamp/solder, crimp/solder or solder attachment methods. As with the other over 40,000 RF, microwave and millimeter wave products from Pasternack, this 75 Ohm SMB connector series is in-stock. Not only are these connectors with 75 Ohm SMB in stock, they will ship the same day as they are ordered.
-
Product
PCIe Gen3 4K at 500 Fps High Speed Compact Camera for Testing
CB160CG-LX-X8G3
-
4K at 500 Fps High speed, compact, fast camera for: Vehicle Impact, Airbag Deployment and Safety Restraints Testing, Digital Image Correlation (DIC), Projectile, Explosives, Ballistics, Combustion and Missile Launch Tracking, Fluid and Flow Visualization, Sports Broadcasting, Commercial Film, Television and Studio Production, Fluidics and Particle Image Velocimetry (PIV), Flat panel inspection (FPD), printed circuit board (PCB) examination and more.
-
Product
Chip Scale TVS Arrays
-
ProTek's patented* Flip Chip TVS Arrays are designed for small circuit board applications with limited size and space availability. To reduce installation costs, the Flip Chip can be mounted directly onto the printed circuit board; similar to chip resistors and capacitors. These devices are ideal for use in portable electronics such as Cellular Phones, Cellular Phone Accessories, Personal Digital Assistants (PDAs), Laptops and Pagers.
-
Product
Extender
3690-6
-
VECTOR Electronics and Technology, Inc.
Contact fingers at the other end of extender card are gold plated provides low insertion force and positive contact with printed circuit boards. Receptacles have double row phosphor bronze contacts with high quality, long life mounted on top of the extender.
-
Product
Mini SMP Connectors
-
Mini SMP connector series, also known as SMPM connectors, are ultra-miniature, high frequency connections commonly used in applications up to 65 GHz. Mini-SMP connector category will terminate to coax or PCB (printed circuit board) and many mini-SMP connectors are hermetically sealed. Pasternack mini SMP connectors are built to precise microwave and RF industry specifications and many are RoHS and REACH compliant. SMP mini connector products are built in male or female gender with 50 Ohm impedance. Mini-SMP connectors are available in straight or right angle versions, as well as, mountless options. These Mini-SMP connector designs include solder attachment methods. As with the other over 40,000 RF, microwave and millimeter wave components from Pasternack are in-stock. Not only in stock, but these SMP mini connectors will ship the same day as they are purchased.
-
Product
PRODUCTION PCBS PRINTED CIRCUIT BOARDS
-
Printed circuit boards are mass produced for a variety of reasons; it is often the final step after a successful printed circuit board prototype run. Typically, engineers first make and create a design on a computer to test its functionality. Then they prepare a board layout and test with prototypes.
-
Product
Control Board For Testing PCBs
TCC 1800
-
The TCC1800 Test Controller Card is a generic control board for production testing of printed circuit boards (PCBs). The board is controlled by a command language on a PC to which it is connected via a galvanically separated USB interface. The TCC1800 is designed to work with positive voltages up to 24V. All inputs and outputs are protected against higher voltages however. The card provides basic IO: Analog and digital interfacing, counters, PWM outputs, bidirectional I/O, Serial (UART) and I2C interfacing.
-
Product
Filters / Splitters / Detectors
-
DiCon’s 100 GHz WDM is designed to multiplex and demultiplex signals in multi-wavelength systems based on the ITU 100 GHz grid. The component uses a thin film filter mounted between a pair of GRIN lens collimators. The 100 GHz WDM is housed in a compact, environmentally stable package that offers superior resistance to humidity and temperature and is suitable for mounting on a printed circuit board or within a module.
-
Product
1149.1 Boundary Scan Feature, GTE 10.00p
K8212B
-
Boundary scan is a method for testing interconnections on printed circuit boards. Keysight’s Interconnect Plus Boundary Scan feature enables all the tools required to develop and execute this foundational test method on the board under test.
-
Product
Fastest In-Circuit Test Platform
TestStation
Test Platform
Teradyne’s TestStation in-circuit test systems provide electronics manufacturers with reliable high-quality, high-volume testing for the latest printed circuit board assembly (PCBA) technologies that are used in automotive, industrial, computing, consumer, communications, and defense end-products.
-
Product
PWB Interconnect Stress Test
-
PWB Interconnect Solutions Inc.
Services to test the reliability of Printed Circuit Boards. PCBs).Coupon Inspection and Electrical Prescreen. Coupon Testing. Failure Location via I/R Photo Imagery. Failure Analysis.
-
Product
PHOTOMASK INSPECTION MACHINE
NEGATIVE FILM
-
Negative film and photomask inspection originated from the extensive use of printed circuit boards. Negative films and photomasks are used in large quantities. The early detection method is to use the "inspection light table" for inspection, which requires too much manpower and material resources, and manual testing may be due to eye fatigue and negligence.
-
Product
Design, Manufacture & Test of Complex RF/Microwave Printed Circuit Boards (PCBs)
-
Teledyne Labtech specialises in the design, manufacture and test of complex RF/Microwave printed circuit boards (PCBs). - Technology driven – we innovate- Turnkey - one stop for manufacture, assembly & test- Focused – technical design support for RF/microwave and large format PCBs
-
Product
PXI-2535, 544-Crosspoint, 1-Wire PXI Matrix Switch Module
778572-35
Matrix Switch Module
544-Crosspoint, 1-Wire PXI Matrix Switch Module—The PXI‑2535 is a high-density 4x136 PXI matrix switch module that is ideal for routing low-power DC signals in validation test systems of mass produced devices such as semiconductor chips and printed circuit boards (PCBs). Featuring field-effect transistor (FET) relays, the PXI‑2535 offers unlimited mechanical lifetime and switching speeds up to 50,000 crosspoints/s. It also features onboard relay counting for relay monitoring and deterministic operation with hardware triggers to improve test throughput.
-
Product
PCB Design and Assembly
-
Innovative Circuits Engineering, inc
Turnkey services for Printed Circuit Boards: Design, Fabrication, Assembly and Testing
