-
product
Space Simulators
A6H Series
Bemco offers up-to-date space simulators incorporating all of the preferred features needed for reliable combined temperature and high vacuum testing. The A6H series includes a fully integrated and appropriately sized PCL-III Portable Liquid Chiller utilizing liquid nitrogen for cooling. The PCL-III is mounted within the A6H system structure and permanently attached to the chamber thermal shroud. Mechanical cooling is available as an option.
-
product
Space & Science Imaging
Teledyne e2v has been trusted to design and deliver CCD and CMOS imaging sensors and sub-systems for over 150 space missions by the world's largest space agencies, including NASA, ESA, JAXA, CNSA and most recently for the Russian-led World Space Observatory.We offer space imaging solutions, including space qualified imaging sensors, arrays and sub-systems for space science, ground astronomy and Earth observation; helping solve the mysteries of the Universe and understand climate change on Earth.
-
-
product
Space Flight Gimbals & Controllers
Precision gimbals for pointing and tracking, stabilized platforms, and pedestals have been a specialty of CAES for more than 60 years. We have deep and broad experience in both terrestrial and space applications.
-
product
Space
Honeywell Aerospace Technologies
Honeywell’s space portfolio is made up of highly innovative products that span human space missions, launch vehicles, microelectronics and satellite payload and bus technology.
-
product
High Speed Free Space Optical Detectors
High speed optical detectors use special photodiodes with high speed electronic circuits to convert fast optical pulses to electrical signals for measurement. Unlike our optical receivers, these detectors do not include a transimpedance amplifier.
-
product
Space Charge Measuring Equipment
PEA
The increasing request for energy quality and, thus, insulation system reliability, associated with significant steps in the manufacturing of new insulating materials, are pushing strongly the research on new techniques for the diagnosis of insulation ageing.
-
product
Space Power Solutions
Teledyne e2v HiRel Electronics (HiRel) offers leading edge power solutions dedicated for high-reliability applications. The introduction of Galium Nitride (GaN) technology solutions enable high power density designs with four times less space requirements than traditional MOSFETs. The Teledyne HiRel Point-of-Load (POL) products combine multiple load capabilities, outstanding radiation performance with high levels of integration and easy to use features.
-
product
Frequency and Timing System for ESAs Deep Space Antennas DSA1&2
TimeTech Frequency and Timing System for ESAs Deep Space Antennas DSA1&2
-
product
Gratings for Space-Flight
HORIBA Scientific (with its Jobin Yvon Grating Technology) has 50 years of experience in space-flight gratings. The first space flight ruled gratings were produced for the CNES mission D2A in early 70’s. Since that date, HORIBA Scientific has continuously produced some of the most technically-challenging gratings ranging from off-plane X-ray replica gratings to aspherical 5800gr/mm VLS gratings for the FUV and Transmission Grisms or very low groove density VNIR-SWIR ruled blazed gratings. HORIBA Scientific gratings (master and replica) have been space qualified and are TRL9.
-
product
Charge Coupled Device (CCD) Image Sensors for Space and Ground-Based Astronomy
(CCDs) for Space science, Ground-based Astronomy, and Earth observation applications with an impressive record of successful deliveries to a wide range of customers over 40 years.All Teledyne e2v devices can be supplied partially or fully customised to fit the application and achieve the best possible system performance. CCD image sensor design, manufacture, test and characterisation are carried out in-house enabling control from start to finish. Multi-polysilicon, multi-metal and back-illumination options are available for high resolution, high sensitivity and very low noise.
-
product
Vertical Space Transformers
ST
The Space Transformer (ST) is an integral part of the probe card, utilized between the probe head and the PCB. Nidec SV Probe provides a wide variety of space transformation options including: • WST™ (Wired Space Transformer) • MST™ (Modular Space Transformer) • MLC (Multi-Layer Ceramic) • MLO/Mini-PCB (Multi-Layered Organic) • Multi-Site MLO Reflow of Package Substrate • MLC with MLTF to 50µm PitchOne of the main priorities for Nidec SV Probe is the internal development and manufacture of our own probe card components. We now offer in-house manufactured space transformer technologies with shorter lead time and competitive pricing. Contact your sales representative to learn more about our internally manufactured STs or any of our other ST technologies.
-
product
Space Flight Components
A tec, Inc. specializes in the design, manufacture, and integration of complex test systems and quality critical components. Our production engineering expertise separates us from other manufacturing companies when both reliability and cost are important. Atec has the best in 5 to 9 Axis CNC machining, coordinate measuring machines (CMMs), 3D additive metal and plastic printers, 9-Axis capable waterjet, cryogenic liquid flow test benches and environmental test chambers. We can deliver to the tightest tolerances and most exacting requirements. We can advise our customers on electron beam welding, friction joining, electronic test, environmental test, acoustics, vibration and many other technologies that can reduce manufacturing and operating costs. We are currently manufacturing liquid rocket engine fuel and oxidizer valves for multiple launch vehicles and have participated in 158 consecutive launch successes. Atec manufactured and tested advanced lithium-ion battery adapter plates that manage power for the International Space Station. Atec is designing, manufacturing, and testing power flow modules that work to prevent system failure on the human crew capsule (CCTS) that will transport astronauts to/from the ISS. Atec was awarded NASA Agency-Level Small Business Subcontractor of the Year , SBA Region VI Subcontractor of the Year for our support to NASA and Boeing and we were named a DCMA Top 500 Supplier.
-
product
Space-Qualified Products
Teledyne RF & Microwave has a rich history with more than 40 years of space heritage without any in-flight failures. We serve the commercial, scientific, military, and government communities with best-of-breed space solutions. As one of the first companies receiving MIL-PRF-38534 Class K certification, Teledyne earned the space community's trust by commercializing and supporting the industry's most comprehensive line of space-qualified products, from components to solid-state power amplifiers to integrated microwave assemblies.Teledyne's quality certifications include MIL-PRF-38534, Classes H & K (TRB Option). Our space-qualified RF and microwave portfolio covers frequencies from 5 MHz to Ka-band. Explore more below for an overview of our product offerings and capabilities.
-
product
Space Qualified Oscillators
Our range of space qualified precise low noise rubidium oscillators. These highly accurate space qualified frequency references are used in Satellite Navigation Systems, Intelligence Reconnaissance Satellites, Military Communication Satellites, Deep-Space Survey and Space Stations
-
product
Rack Mount Kit For N8900 Autoranging System DC Power Supplies
N8958A
The N8958A is a rack mount kit that provides all the necessary hardware to rack mount one N8900 Autoranging System DC Power Supply (any of the 28 models) in only 3U of rack space when installing in a Keysight rack.
-
product
Low Noise Amplifier
LNA
Teledyne Defence & Space (TDS) Low Noise Amplfiers (LNA) are designed to amplify very low power signals without degrading the signal-to-noise ratio.An amplifiers is designed to increase the power of both the signal and the noise however the Low Noise Amplifier is specifically designed to minimise the additional noise so important information should not be lost.
-
product
Electromagnetic Force Fatigue And Endurance Testing System
EMT Series
High-speed repeated load tests can be carried out with a maximum velocity of 2 m/s, and maximum stroke of ±50 mm, using clean and quiet electromagnetic force as the driving power, without the use of oil. The test space is large so environmental tests can also be carried out using the constant temperature tank (option).
-
product
ATCA CO6 DC 6 Slot 7U
The AdvancedTCA® CO6, 6-slot chassis, DC version with front-to-rear cooling is dedicated for NEBS environment where the space is limited.
-
product
Low Profile Compression Only Load Button Load Cell with Mounting Holes
LBC SERIES
The LBC Series (Load Button) load cells are offered for compression only applications where space is limited. The matching surface must be flat and at least the diameter of (D1). The loading diameter (D2) is slightly convex for accurate load distribution. Counter bored mounting holes are provided for fastening down from the top. These sensors are manufactured from heat treated 17-4ph stainless steel and sealed for use in most industrial environments.
-
product
Solid State Relays
As well as being slim and thus saving panel space, The relays are very strong, have a large contact area and non-bendable pins. Connection to a PLC is easy and achieved faultlessly in a few seconds via click connectors. In addition, power switching in G3RV relays with DC outputs is managed by a MOSFET in the output, which has ideal heat dissipation characteristics.
-
product
Single Beam Interferometer
10705A
The Keysight 10705A Single Beam Interferometer, the smallest linear interferometer, is designed for making low mass or limited space single axis measurements. It is ideal for use in disk drive and other confined space applications. The single beam interferometer is called that because the outgoing and returning beams are superimposed on each other, giving the appearance of only one beam traveling between the interferometer and the retroreflector.
-
product
Air Quality Meters
An indoor air quality meter is used in confined spaces to prevent mold, to monitor CO2 levels, or to detect gas leaks. Whether portable or fixed, handheld or wall mounted, air quality monitoring equipment is essential for ensuring health and safety. At PCE Instruments, you will find air quality monitoring devices that meet various industry standards relating to personal safety and that are used to detect, measure and monitor relative humidity, ambient temperature and / or levels of carbon dioxide (CO2), volatile organic compounds (VOCs), formaldehyde (HCHO), freon and other refrigerants (CFC / HFC), phosphine (PH3), hydrogen sulphide (H2S), carbon monoxide (CO), nitrogen dioxide (NO2), oxygen (O2), ozone (O3) and other flammable, hazardous or toxic gases.
-
product
EMF Measurements/EM Measurements/Electromagnetic Radiation
Holland Shielding Systems B.V.
Electromagnetic fields cause interference in electronic devices and may affect the health of people close to where the fields are generated. It is important to recognize this at an early stage in a construction process, for instance at a future construction location or while construction is already underway, so that budgets are not exceeded. By means of field-strength measurements one can chart the existing electromagnetic fields and radiation emitted by GSM, UMTS antennas and transformer spaces, to mention a few examples. These measurements can help determine the best location in the new building for rooms where sensitive measurements are to take place, e.g. in hospitals or nano laboratories. And last but not least, field-strength measurements can detect sources of interference and can be part of a scheduled check of existing screened spaces and Faraday cages.
-
product
LED Color Sensor
Ultra FINN
The Ultra FINN™ is designed to make testing LEDs as simple and reliable as possible. Improved accuracy provides measurements for a wider color range, greater discrimination between hues and increased precision. The Ultra FINN’s small size and streamlined shape allows for testing very closely spaced LEDs and its faster speed decreases test times significantly.
-
product
3D Imaging Sensor
The GS 3D sensors, can be used in applications such as bin picking, robotic manipulation, sorting products, mold clearance checking, and space monitoring and object recognition. In addition, the 3D technology will aid in determining spatial positions and measurements.The GS 3D images larger objects at longer distances and does so in milliseconds without the cycle time and motion required by scanning-based methods.
-
product
Durable, Ultra Small & Flexible Test Assembly
StormFlex® 034
Storm Flex® line of flexible cables, the 034 diameter cable offers the same superior mechanical benefits in a new miniature size.Its ruggedness and durability combined with its ultra-small size, very low weight, and extreme flexibility make Storm Flex® 034 cable assemblies the perfect fit for applications such as:- Test & Measurement ~ where flexibility and robustness minimize mating errors.- Systems ~ with complex installation or deployment that can compromise mechanical & RF stability.- Gimbal ~ with requirements for cables operating to 50 GHz.- Digital Test ~ needing minimized stress at the connector to connector interface.- High Density ~ utilizing multi-cable interconnects with centerline spacing as low as 0.07 inches.Storm Flex® 034 cable is also recommended as a semi-rigid replacement in applications where a sem-rigid cable is impractical to deploy and routing may result in assembly breakage or electrical failure.
-
product
SparkFun GPS Breakout
NEO-M9N, U.FL (Qwiic)
The SparkFun NEO-M9N GPS Breakout is a high quality GPS board with equally impressive configuration options. The NEO-M9N module is a 92-channel u-blox M9 engine GNSS receiver, meaning it can receive signals from the GPS, GLONASS, Galileo, and BeiDou constellations with ~1.5 meter accuracy. This breakout supports concurrent reception of four GNSS. This maximizes position accuracy in challenging conditions, increasing precision and decreases lock time; and thanks to the onboard rechargeable battery, you'll have backup power enabling the GPS to get a hot lock within seconds! Additionally, this u-blox receiver supports I2C (u-blox calls this Display Data Channel) which made it perfect for the Qwiic compatibility so we don't have to use up our precious UART ports. Utilizing our handy Qwiic system, no soldering is required to connect it to the rest of your system. However, we still have broken out 0.1"-spaced pins in case you prefer to use a breadboard.
-
product
PICMG 1.3 Half-size SBC
Axiomtek's PICMG 1.3 half-size CPU cards (185 x 126 mm) offer high performance PCI Express slot as interface to the backplane, and improve I/O bandwidth and graphic performance from the original PICMG 1.0 specification. The PICMG 1.3 half-size SBC is specially designed for space concernd applications.
-
product
Free Space Optical Receivers
These optical receivers have bandwidths in the DC to GHz range for detecting high speed free space optical signals with the lowest noise and cleanest responses possible.
