Visual Fault Finders
Apply light to optical fibers, enabling visual inspection to determine integrity.
-
Product
Fault Injection Module
WF 3154 C-Series
-
The WF 3154 from WireFlow is a 4-channel Fault Injection Module for Compact RIO. Each channel provide three solid state relays that can be used to create electrical fault conditions like: Open circuit, Short circuit to battery, Short circuit to ground.
-
Product
PXI 16-Channel 4-Bus 2A Fault Insertion Switch
40-197A-002
Fault Insertion Unit
This 16-channel fault insertion switch is primarily intended for routing simulated fault conditions in automotive and aerospace applications involving the reliability testing of safety critical controllers.
-
Product
Cable Fault Locator
TX2001
-
Lowest Cost Full Specification Professional Graphical TDR Rugged Palm Top Design 350g (12oz) 5 Measurement Ranges up to 3000m (10,000ft) 50, 75 & 100 ohm Selectable Impedance Built in Tone Generator for Pair Tracing & Identification Suitable for testing all Communications Cables Water & Dust Proof to IP54 Complete with tool-belt holster & test leads
-
Product
Cable Fault Locator ECFL 30
ECFL 30
-
Compact precision active/passive, AC/DC bridge with dual channelTDR for fault location on balanced loaded and unloaded cables.
-
Product
Space-Magnetic Field Visualization System
EPS-02EMF System
-
The system detects position of the magnetic field sensor on thebasis of the image on the camera first of all and then, recognizes strength of the signal that is measured by the sensor upon frequency analysis of the signal almost simultaneously. Finally, visualization of the strength dispersion in composition with the real image of the measured object can be realized on screen of PC.
-
Product
PXI Fault Insertion Switch, 7-Channel, One Fault Bus, 20 A, Hardware Interlock
40-194A-001-HI
Fault Insertion Unit
The 40-194A-001 is a 7-Channel PXI Fault Insertion switch with hardware interlock and one fault bus, designed for the simulation of fault conditions in automotive systems. As well as high current handling of 20A, very low currents can also be switched.
-
Product
Ground Detection and Earth Fault Location Equipment for Ungrounded or Floating DC Systems
ZX3
-
The ZX3 is a ground fault locator that finds grounds (current leakage) on a battery system positive rail, the negative rail, on both rails simultaneously, in a field device, battery bank or solar array/string, regardless if they are high resistance or low resistance or in a capacitive environment. It also can provide more information about the DC ground than any other equipment available, providing maximum analyzing capabilities.
-
Product
Cable Fault, Test And Diagnostics
-
Allows an operator to test twisted pair cables for faults without physically disconnecting the cables from the switch.
-
Product
Test Executive for Visual Development, Database Storage, and Run-Time Execution of Test Strategies
TestBase
-
TYX TestBase is a test executive that supports the visual development, database storage and run-time execution of test strategies (also known as test plans or test sequences).TestBase integrates third-party applications such as: test programming languages, document viewers, report generators, database engines, Configuration Management systems and diagnostic tools.Its modular and open architecture enables system integrators and end-users to customize and extend the product and to integrate additional third-party applications.
-
Product
Terrestrial Signal Finder
Satlink WS-6905
-
Jointron(Quanzhou)Industry Co.,Limited
1.Satellite TV Equipments Including satellite receivers, satellite signal level meter, satellite finder(meter), HD DVB-S2 Receivers, DVB-S2 Meter with Spectrum Analzyer(in real time) 2.Terrestrial TV Equipments Inlcuding DVB-T receivers, DVB-T Meter, HD MPEG-4 DVB-T Meter, HD MPEG-4 DVB-T Receiver, SD MPEG-4 DVB-T Receiver 3.Combo Equipment: Including SD MPEG-2 Satellite&Terrestrial Combo Meter, HD MPEG-4 satellite&Terrestrial Combo Meter
-
Product
In IIoT And Industry 4.0, Customers Need Data Visualization For Process Management. The FPM-710SW Is A Sleek, Industrial-Grade Touchscreen Monitor.
FPM-710SW
-
USB Type-C connection touch monitor 1920 x 120010.1" WUXGA TFT LED LCD with true-flat touchscreen16:10 wide screen aspect ratio, increases viewing area by 40%Supports multi-touch control via USB interface in Windows 7/8/10 OSSlim design enables easy installation with Build-in panel mount kitSupports various mount options: panel, desktop, and VESA armTouchscreen with reliable glass surface and P-CAP touch controlRobust system with Die-casting aluminum chassis and IP66-rated aluminum alloy front bezelFirst single cable industrial touch monitor
-
Product
Visible Fault Locator
FiberLink 6656
-
Fiberlink 6656 Visible Fault Locator is a light-weight, hand-held tool used to quickly troubleshoot faults in the continuity of both single-mode and multimode fibers, especially at fiber launch points or in OTDR dead zones.
-
Product
Instrumented Runway Visual Range Transmissometer System
AGIVIS 2000
-
Aeronautical & General Instruments Ltd.
AGIVIS 2000 is a transmissometer-based Runway Visual Range (RVR) system that provides the highest possible levels of accuracy. The first generation of AGI RVR systems were developed in co-operation with the UK Met Office and CAA, and AGI has been supplying RVR systems for more than 25 years. AGIVIS 2000 systems are currently operational at major international airports certified for instrument landings up to and including CAT IIIB. AGIVIS 2000 is fully compliant with ICAO, WMO and CAA requirements. The system consists of transmissometer field sites, background luminance meters, runway lighting interfaces, data processing equipment and archive storage and backup. It can drive multiple full-colour dedicated RVR displays. Systems can be supplied fully installed with comprehensive engineering and operator training, and post-installation support is available worldwide.
-
Product
PXI/PXIe 1000Base-T1 Dual Multiplexer With Fault Insertion, Dual Channel
40-204-002
Multiplexer Module
The 40-204-002 (PXI) and 42-204-002 (PXIe) are dual channel differential multiplexers designed to simulate common faults on high-speed two wire communication interfaces such as 1000Base-T1. They are available with support for 1 or 2-channels of two wire serial interfaces. Each channel pair can be looped out to external equipment or the switches can be used simulate a channel open fault. Using the fault bus, switches can simulate a short between both wires or a short to one of two externally applied fault conditions – such as battery supply or ground - via two fault buses.
-
Product
RS-485/RS-422 Fault Protected
-
Renesas' fault protected RS-485/RS-422 transceivers, also known as overvoltage protected transceivers (OVP), offer robust fault tolerance and high performance.
-
Product
Cable Fault Locator
TW3304N
-
Techwin(China) Industry Co., Ltd
The Perfect Handhold Tester Series Cable Fault Locator TW3304N is the most portable test instrument in the industry. It adopts the OTDR technical principles and integrates the powerful analysis software, which enables the TW3304N fiber ranger detect fiber faults location more accurate and easy.
-
Product
CAN/FlexRay/Differential Bus PXI Fault Insertion Switch - 8 Channel
40-200-008
CAN Interface
This PXI Fault Insertion module is designed to simulate common faults on two wire communication interfaces such as CAN Bus. This module supports 4 or 8-channels of two wire serial interfaces. Each channel can simulate an open fault in either or both wires, a short between both wires or a short to one of eight externally applied fault connections, such as a battery connection or ground, via four fault buses. Each channel can support up to 0.3A and is rated to handle up to 100V between the wire pairs. The wire pairs have controlled transmission line impedance suited to most differential pair signalling systems, including fast CAN Bus interfaces and RS232. Each fault bus is capable of carrying 2A allowing multiple channels to be connected to the same fault condition. Additionally, each fault bus features a changeover relay to allow the user to connect alternative fault conditions to the fault buses.
-
Product
Magnetic Field Visualization
magview
-
The magview is a mobile hand-held device equipped with a magneto-optical (MO) sensor for the rapid visualization of magnetic structures and stray fields with the eye.
-
Product
Visual Evaluation and Lab Tools
-
Tools for visually evaluating color and excelling color development.
-
Product
MPO Visual Cable Verifier Kit
KI-TK824
-
Kingfisher's unique and innovate MPO Visual Cable Verifier Kit is a quick, versatile and inexpensive way to visually check MPO cable installations and patch leads for polarity and continuity, and overall end face condition. Just connect the source, and view the far end with the microscope to observe the repeating color pattern at the far end. Fiber 1 is easily identified with a winking light.
-
Product
Cable Tester, Coax Cable Mapper 8 ID Finder with Toner
TCT-128
-
A handheld testing device designed for CATV and security installers to test multi-run coaxial cable systems terminated with "F" or BNC connectors. Uses eight color coded ID finders to locate and identify cables.
-
Product
Cable Fault Location System
BAUR Syscompact 2000 Portable
-
Cable fault location system Syscompact 2000 portable. The cable fault location system Syscompact 2000 portable is used for precise location of high-resistance and intermittent faults in low and medium voltage cables.* Fast and reliable* Precise, dependable cable fault location* High performance high voltage unit* Integrated proven cable fault pre-location methods
-
Product
Automated Visual Control System for Canned Food in Glass Containers
-
The system is designed for visual quality control of food packaging products. The level of filling the jar with the product, as well as its closure, is monitored. During the development of the system, smart cameras from Sick were used, but a special illumination of our design was used to improve the image quality.
-
Product
Vector Finders with InternalAttenuators
VF-145 LA AND VF-145 LMA
-
The VF-145 LA and LMA models are functionally the same as the VF-145 L and LM on both electrical performance and mechanical specifications. However, the LA and LMA models include an internal PIN diode attenuator that provides up to 12 dB of attenuation (measured at 150 MHz, attenuation decrease slightly as operating frequency increases) to the incoming radio signal. This attenuation occurs after the signal is received by the unit and phase shifted for processing, but before it is placed on the coax feedline to the receiver. In addition, the PIN diode utilized will absorb short burst of RF should transceivers be keyed accidentally by the user. This feature aids in very strong signal DF operations but will not totally guarantee against system overload under very strong RF emissions.
-
Product
NI-9852, 2-Port, Low-Speed/Fault Tolerant C Series CAN Interface Module
779707-01
CAN Interface
2-Port, Low-Speed/Fault Tolerant C Series CAN Interface Module—The NI-9852 is a fault‑tolerant Controller Area Network (CAN) interface for developing FPGA-based applications with the NI‑RIO driver on CompactRIO. The NI‑9852 is ideal for low-level FPGA‑based control and triggering applications that are programmed using the LabVIEW FPGA Module. The NI‑9852 is ideal for byte-level manipulation of CAN frames using the LabVIEW FPGA Module. The NI‑9852 is only compatible with CompactRIO systems.
-
Product
Computer Vision and Visualization
-
Fraunhofer Institute for Telecommunications
The Computer Vision and Visualization Department consists of three research and development groups working on innovative technologies in the field of monocular, stereoscopic and multichannel video processing. It covers the entire processing chain from original capture to rendering, with a focus on advanced 2D and 3D analysis, post-production synthesis, computer vision, image understanding, human-machine interaction, and immersive media , The department also has expertise in processing complex systems consisting of multiple cameras, sensors, displays, projectors or screens.
-
Product
IoT Dashboard for Data Streaming and Visualization
Initial State Software
-
Stream data from your devices and services to beautiful interactive cloud-based data visualizations. Designed for monitoring, test, and data streaming applications, Initial State provides a scalable IoT streaming backbone with world-class anywhere-accessible data visualizations. Create real-time IoT dashboards using streaming data from any connected IoT device, PC, or via codeless integrations with instrumentation like the Keithley Datalogger/DAQ 6510.
-
Product
PXI Fault Insertion Insertion Switch Modules
-
Our PXI Fault Insertion Insertion Switch Modules feature a breakout arrangement that allows faults to be attached to the sensor lines, this includes the breaking of a connection or the adding of defect – all of which can simulate connectivity problems in the system.
-
-
Product
Pole Mounted Detector of PtG and PtP faults in 6-69V Line
LineTroll 111K
-
The unit mounts 3-5m below the conductors and monitors all three phases. The indicator is powered by replaceable long-life lithium batteries which have a lifeexpectancy of 10-15 years. It provides a 360 degree visibility for indication both for transient faults and permanent faults.
