-
Product
EFT/Burst Simulators
-
Suzhou 3ctest Electronic Co.,Ltd.
High-end test instrument of EFT/Burst for new energy, which fully comply with CE and CCC certification. With a built-in three-phase five-wire automatic coupling /decoupling network EFTN 69100T, it can meet the requirements of new energy test system and high power load test. It is featured with good reliability, stable performance and easy use.
-
Product
Simulators
-
In-Phase Technologies simulators are designed to simulate our customer’s operating product, allowing them to perform testing and “what if” scenarios
-
Product
NIBP Simulator
vPad-BP
-
vPad-BP, part of the vPad-A1 family, is a NIBP (non invasive blood pressure) simulator designed to test the accuracy and repeatability of the NIBP function on Patient Monitors. User programmable settings allow for easy on site configuration to accommodate new models of NIBP devices.
-
Product
Reach-In Solar Panel Test Chamber
-
For testing various size solar panels WIEBER designs and manufactures Solar Panel Test Chamber. The test are to be performed according to various standards of ASTM, IEC, UC etc. Solar panels need to pass environmental tests as per IEC and other standards requirements to prove their long term performance and resistance to temperature and humidity extremes. Solor Chamber also known as Solar Photovoltaic Testing Chamber and PV Module Test Chamber.
-
Product
Multi-channel Battery Simulator
FT8340
-
Shenzhen FaithTech Technology Co., Ltd.
The FT8340 series is a high precision, multi-channel, dual quadrant programmable battery simulator.The current of the simulator can be charged and discharged，and supports various fault simulations, which can not only meet the requirements of BMS testing, but also meet the ATE testing of consumer electronics products.There are at most 12 channels in a device, and each channel is electrically isolated, which is convenient for users to use in series. The built-in upper computer software is easy to operate, flexible and easy to use. It supports single channel programming operations, multi-channel editing operations, and multi process programming operations.
-
Product
Single-Output Software-Defined GNSS Simulator
BroadSim Solo
-
Designed to address the permanent challenges that engineers face with laboratory capacity and availability, BroadSim Solo was developed to bring advanced GNSS scenario creation to your desk and propel development cycles.
-
Product
Simulation
-
Synopsys' high-performance simulation products help engineers find design bugs faster and achieve timely coverage convergence to create high-quality designs. The Synopsys suite of simulation solutions are tightly integrated, best-in-class technologies that allow designers to find bugs quickly and easily, significantly improving the quality of the most complex designs and enabling first-pass silicon success.
-
Product
Offline Programming, Advanced Simulation & Digital Twin
Silma
-
Improve your 3D measurement experience with a winning combination: Silma, for advanced simulation and digital twin of your 3D measurement process, and Metrolog for on-machine execution and analysis.
-
Product
Simulation Tools for Analog and Power Electronics
SIMetrix/SIMPLIS
-
Fast and accurate simulator for switching power circuits, fully utilising the SIMetrix development environment.
-
Product
Solar Radiation Sensors
-
The solar radiation sensors that Campbell Scientific offers come in a variety of designs: pyranometers, net radiometers, quantum sensors, and pyrheliometers. These sensors measure various aspects of the energy imparted by the sun on the Earth’s surface. A leveling fixture fitted with a bubble level may be required to accurately install solar radiation sensors.
-
Product
4, 8, 16 And 32 Channels ARINC429 Test & Simulation Module CompactPCI-Express/PXI-Express (3U)
ACE429-3U-x
Simulator
4, 8, 16 and 32 channels ARINC429 Test & Simulation module for CompactPCI-Express/PXI-Express (3U).
-
Product
Lithium battery 128kWh Lifepo4 Battery pack 280Ah with BMS for Solar Energy Storage System
SPVLI-128kWh
-
Zhejiang Sandi Electric Co., Ltd
ESS lithium battery system is composed of lithium battery modules, BMS system, PV charge controller, AC/DC Charger, central control unit CCU, temperature detector, integrated structure and other parts; the solar panels in the system are battery storage and power for output; BMS module completes the detection and control of voltage, current, temperature, SOC, SOH and charging and discharging related parameters of power battery pack; PV controller and inverter realize bidirectional AC/DC function to meet the charging and discharging conversion demand of power battery pack; each detector is used to monitor the ambient temperature in real time to ensure the safety of the system.
-
Product
Capacitance Simulation Card
SET-1220
-
The SET-1220 device is a designed capacitive fuel sensor emulation for NI-SLSC. This card provides eight isolated channels that can emulate capacitance values between 10pF and 800pF. It was designed to emulate capacitive sensors that are typically connected between an excitation voltage on one end and a virtual ground on the other end.
-
Product
2 Port T1/E1/PRI ISDN Simulator PCI
SIM-2PRI-PCI
-
The most inexpensive ISDN PRI simulator on the market. Designed in standard PCI card form factor it has two PRI(T1 or E1) ports allowing ISDN PRI equipment to be connected together just as if they were connected through the ISDN network. Simulator card does not require any OS drivers, completely software independent and it take only power from the host computer.
-
Product
Solar Connectors & Adapters
-
Our SOLARLOK photovoltaic connectors are designed for easy, quick and reliable DC connections for solar technology. With a precision-engineered design, these help achieve the lowest contact resistance to reduce power losses. Our DC Plug and splice connectors provide reliable connection, reducing up to 80% installation time with Insulation Displacement Contact (IDC) technology. Our grounding connectors enable installers to ground the photovoltaic system and create flexibility at the installation.
-
Product
3U VPX RL Thermal Load Simulation Module
-
The 3U power test module is an ideal solution for evaluating heat dissipation in a rugged conduction cooled VPX cage or chassis. This card is a thermal load in the chassis to evaluate the heat dissipation. The chassis can be monitored with temp sensing probes and or FLIR imaging. Different wattages are selected by setting dip switches. The +5 and 3.3V loads are on the top of the module. The +12V and -12V loads are on the bottom side of the module.
-
Product
AFDX ® / ARINC 664 Test And Simulation PMC Module
PMC-664
PMC Module
*Supports IEEE 802.3 10/100/1000 Mbit / s full duplex Ethernet connections*Uses SFPs to support both electrical and optical interfaces*Half-size PCI / PCI-X modules*Simulates multiple AFDX® / ARINC 664 end systems*Standard Ethernet processes simultaneous to AFDX® / ARINC 664*Up to 128 output VLs and 512 input VLs*Upper layer protocol handling (ARINC 653, UDP, IP) managed onboard*DMA for high data rate applications*Windows XP / 7, Linux, and LabVIEW Real Time Drivers & APIs (others on request)Easy to use tool for configuring A*FDX® / ARINC 664 end systems (XML based)
-
Product
Radar Simulator
SPx
-
SPx Radar Simulator is a Windows-based application that generates simulated radar video data, along with any combination of tracks, AIS, navigation and secondary radar. The data may be output in network format (including ASTERIX for radar video and tracks), or as radar signals (video, trigger, ACP/ARP) with the HPx-300 radar output card.
-
Product
MIL-STD-1553 Test & Simulation Interface for PCI Express
PCIe-C1553
-
Avionics Interface Technologies
Dual redundant, single, dual or quad stream configurationsSoftware selectable Transformer, Direct, and Bus Stub Coupling Modes - Concurrent Bus Controller, 31 Remote Terminals, & Bus monitor operation - Full error injection and detection - Multi-level triggers for capture and filtering - Ten high voltage (up from 30V) programmable DIO lines - IRIG-B time code encoder/decoder with free-wheeling mode - Real-Time recording and physical bus replay - x1 Lane PCI Express Host Interface (x4 Physical edge connector) - Application interface supporting C, C++, C#, and .NET development - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
MIMIC® Server Simulator
-
How do you test your management application's scalability to support thousands of servers and devices?How do you test whether a load balancer can handle a Web Server farm without reaching the performance limits?
-
Product
Simulation
-
From structural analysis and computational fluid dynamics to injection molding simulation and advanced, cloud-enabled capabilities powered by Abaqus, SOLIDWORKS® and 3DEXPERIENCE® Works Simulation provide integrated analysis tools for every designer, engineer, and analyst.
-
Product
Flux Valve Simulator
FV Sim
-
This flux valve simulator is designed around the synchro format and is employed in our TA-14 DG panel. This simulator is also available now in a portable enclosure for testing the Sperry or Jet Directional gyros.
-
Product
Troubleshooting Track Circuit Simulators
14900 Series
-
The 14900 seriesTrack Simulator features a front panel with standard set up resistors and terminals and electrically conductive model track to simulate a track circuit suitable for instructional and hands-on training purposes. A locked drawer provides additional switches, potentiometers, and controls that allow selective implementation of many faults commonly found in typical track circuits.
-
Product
PXI 32 Channel Switch Simulation Module
40-480-221
Digital I/O
The 40-480 is designed to simulate the operation of automotive switches where dirty contacts or leaking current can be expected from switch contamination. It allows automotive I/O devices to be tested for correct operation under adverse conditions. The design includes protection circuits that ensure module damage cannot be caused by wiring faults or UUT failures. Each module can support up to 32 channels and is suitable for both 12V and 24V automotive applications.
-
Product
Camera Link Simulator
CLS-221
-
The CLS-221 Camera Link Simulator is an affordable, high-performance video test pattern generator that supports all video formats including those introduced in the new version 2.1 specification. Fully programmable video timing enables the CLS-221 to mimic the characteristics of almost any camera. New features include enhanced timing performance, bayer color support, and additional video patterns. Control is via an RS-232 port, USB, or frame grabber COM port. The CLS-221 also incorporates the AIA validation test pattern.
-
Product
Optical Components & Transmission Simulation Software
VPIphotonics Design Suite
-
VPIphotonics Design Suite™ embeds expert knowledge from our component and transmission design tools in one shared, flexible software environment to support requirements in design, analysis and optimization providing you with the most powerful numerical algorithms tailored for your applications.
-
Product
Laser Source Simulator
MT1888 Series
Laser Source
The MT1888 products are state-of-the-art Laser Source/Spot Simulators (LSS) used for the testing of laser guided munitions such as the Hellfire & Hellfire II missiles, Paveway, and the AGM-65E Laser Maverick missile.
-
Product
Multi-GNSS RF Simulation System
GSS6300M
-
The Spirent GSS6300M is the ideal platform for entry-level and low-cost test requirements. Capable of generating signals from multiple GNSS coherently, the GSS6300M is a valuable tool in development and production test environments.
-
Product
Test & Simulation Interface for PCI Express
PCIe-C1760
-
Avionics Interface Technologies
HS1760/MIL-STD-1760E Test & Simulation Interface for PCI Express
-
Product
Three-Dimensional Electromagnetic Simulation Package
QuickWave-3D
-
QuickWave 3D (QW-3D), is a universal user-friendly three-dimensional electromagnetic simulation package (winner of the European Information Technology Prize in 1998) based on the conformal FDTD method and supplemented with a range of unique models for curved boundaries, media interfaces, modal excitation, and parameter extraction. Complete 3D electromagnetic simulation offer a set of various results from wide area of applications. A lot of processing/postprocessings present a complete offer of comprehensive solutions from microwave components (filters, couplers, resonators, etc.) through antennas, TDR applications, optimisation and parameters sweep to simulation of microwave heating process (with Basic Heating Module) with temperature dependent media, static, rotated or moved heated object(s), and heat transfer.
