-
Product
PCI Resistor Card 2-Channel 1.5 Ohm To 4.09k Ohm With SPDT
50-293-123
Programmable Resistor Module
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Pressure/Vacuum Calibrators
-
Compact, completely self-contained unit designed for calibrating and testing pressure gauges, transducers, pressure switches, and other pressure-sensitive instruments up to 2,000 psi with an accuracy of ±0.25% of full scale.
-
Product
Melting Point Testers
-
These melting point testers are designed to accurately test the melting point of medium used in thermometers, for educational purposes, for quality control, automated process and more.
-
Product
Pitot Static Tester
ADSE 550
-
The ADSE 550 pitot static tester, housed in a plastic carrying case, is a portable, self contained field tester designed to test aircraft pilot ans static systems for leaks as well as the operation and calibration of airspeed, altimeter, engine pressure ratio, manifold pressure indicators, and other vacuum or low pressure units. The tester consists of a hand-operated vacuum pump, a hand-operated pressure pump vacuum and pressure gauges, 5 control valves, an altimeter and an airspeed indicator. The package accessories include two 25-foot hoses.
-
Product
PCI Programmable Resistor Card 4-Channel 2 Ohm To 255 Ohm - SPST
50-294-113
Programmable Resistor Module
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
High Performance Strip Handler
Rasco Jaguar
-
Jaguar is designed for high-volume production testing of ICs on a strip format or in device carrier. It is fully automotive qualified for tri-temperature test and the ideal solution for high parallel testing of small packages at short test times, but also for Power and Sensor devices. Due to the integrated vision alignment and high precision linear motors, Jaguar provides high yield and excellent OEE.
-
Product
Digital/Analog Audit Kit
-
Botron's Digital/Analog Audit Kit insulation and continuity tester is designed for electrical testing. The wide range of test voltages makes the Audit Kit ideal for users involved with ESD testing. The kit gives greater functionality with simplified operation and an ergonomically designed case.
-
Product
35b profile VDSL2 Tester
TM600P
-
*TM-600 VDSL tester specially designed for xDSL line test (xDSL include: ADSL, ADSL2, ADSL2+, READSL, VDSL2 etc) and maintenance It provides xDSL test, PPPoE dial test, DMM test, Modem emulation, line voltage indication and so on.
-
Product
Test Solutions For MROs
-
Through our 50+ years of experience, we’ve designed equipment that test components on nearly all aircraft platforms. Because of our experience and our attention to industry trends, we can anticipate what components you’ll be testing tomorrow. We design our test stands to exceed your current test requirements for simple upgradability to ensure that you’re ready for the future.
-
Product
PXI Programmable Resistor Card 2-Channel 2.5 Ohm to 4.09k Ohm - SPST
40-294-123
Programmable Resistor Module
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
30A, 100MHz High Sensitivity Current Probe
CP031A
-
Teledyne LeCroy current probes are available in a variety of models for a wide range of applications. The full range of Teledyne LeCroy current probes includes models with bandwidths up to 100 MHz, peak currents up to 700 A and sensitivities to 1 mA/div. Teledyne LeCroy current probes are often used in applications such as the design and test of switching power supplies, motor drives, electric vehicles, and uninterruptible power supplies.
-
Product
USB-6255, 80 AI (16-Bit, 1.25 MS/s), 2 AO (2.86 MS/s), 24 DIO USB Multifunction I/O Device
779959-04
Multifunction I/O
80 AI (16-Bit, 1.25 MS/s), 2 AO (2.86 MS/s), 24 DIO USB Multifunction I/O Device - The USB‑6255 offers analog I/O, digital I/O, two 32-bit counters/timers, and analog and digital triggering. The device delivers low-cost, reliable DAQ capabilities in a wide range of applications from simple applications in laboratory automation, research, design verification/test, and manufacturing test. You can add sensor and high-voltage measurement capability to your device with SCC or SCXI signal conditioning modules. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
PXI-6225, 80 AI (16-Bit, 250 kS/s), 2 AO, 24 DIO, PXI Hybrid, Multifunction I/O Module
779296-01
Multifunction I/O
80 AI (16-Bit, 250 kS/s), 2 AO, 24 DIO, PXI Multifunction I/O Module - The PXI‑6225 offers analog I/O, correlated digital I/O, two 32‑bit counter/timers, and digital triggering. The device delivers low-cost, reliable DAQ capabilities in a wide range of applications from simple applications in laboratory automation, research, design verification/test, and manufacturing test. You can add sensor and high-voltage measurement capability to your device with SCC or SCXI signal conditioning modules. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
PXI Programmable Resistor Card 2-Channel 3 Ohm to 32.7k Ohm - SPST
40-294-132
Programmable Resistor Module
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Gyro Test Panel
TA-256
-
Designed to test the KI256 / KI258 panel mounted Flight Director gyros. The panel contains a power supply, the special manufacturers recommended rate board required by SA-103 to properly verify outputs As well as all other electronics required to support by the book testing.
-
Product
PXI 8 Trib Daisy Chain Switch 120Ohm Balance
40-795-001
Switch Module
The 40-795/796 Daisy Chain Switching Module is designed for telecom test applications. It allows production or verification testing of SONET/SDH transmission multiplexers switching 2MBit/s or 1.5MBit/s data over 100 or 120 balanced lines.
-
Product
RF/Microwave PCB
-
With unique expertise and decades of experience in complex RF PCB and Microwave Printed Circuit Boards, Teledyne Labtech offers a “one-stop” solution for the design, manufacture and test of the most demanding RF/Microwave PCB designs.
-
Product
ATPG with Embedded Compression
TestKompress
-
TestKompress is an automatic test pattern generation (ATPG) tool that provides the highest quality scan test with the absolute lowest test cost. TestKompress has an industry-proven ATPG engine that applies effective fault models to your entire logic design. Manufacturing test costs are held in check by an award-winning test pattern compression technique called Embedded Deterministic Test (EDT).
-
Product
PCI Resistor Card 4-Channel 1 Ohm To 255 Ohm
50-293-013
Programmable Resistor Module
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Traction Test Rectifiers
-
A traction test system is defined as a rectifier with a DC output voltage above 400 VDC to a maximum of 4,500 VDC. (Kinetics manufactures only air-cooled systems) A Kinetics test system includes the required OSHA designated safety features for testing power supplies as a minimum for operator interface.
-
Product
8Ch Speaker/Receiver Unit Tester
BK9012
-
Based on the BK2120A Audio Analyzer, the BK9012 is designed to quickly test microspeakers or receivers 4~8 at a time at a rate that you’ll find hard to keep up with. It tests various frequency characteristics and also rub & buzz so you know the quality of your product is maintained. And of course, you can track the accuracy and stability of your process using the data you’ve saved on about 4 million microspeakers (based on a 6 second total test + load time) per month.
-
Product
Test Signal Generators
-
MicroImage Video Systems has a broad array of video test signal and color bar?generators designed for many applications from laboratory and testing to embedded systems. MicroImage Video Systems can design a video test signal generator for your applications. In fact, we have designed many more custom test signal generators that we offer as standard products. Small size is important and our video test signal generators start at just 1.5 inches square.
-
Product
Advanced Power System - DC Power Supply, 40 V, 50 A, 2000 W
N6972A
DC Power Supply
The N6972A is designed for automated test equipment (ATE) applications where high performance is critical.
-
Product
TACAN/DME Station Tester
EDST300
-
The R&S®EDST300 TACAN/DME station tester is an analyzer designed for commissioning, testing and servicing pulsed terrestrial navigation systems.
-
Product
Variable Resistor Load Bank
REOLOAD 100
-
A variable resistor load-bank with fixed stages connected in parallel and switched in, as required, with an adjustable stage for fine trimming. Designed for testing equipment under load. 1000V (AC or DC). 250A and 2500
-
Product
AC / DC Electronic Loads – Benchtop Testing to Automated Test Systems
-
Chroma Systems Solutions, Inc.
Chroma is the global leader in Electronic Load manufacturing. Chroma’s AC Electronic Loads are designed for testing uninterruptible power supplies(UPS), Off-Grid Inverters, AC sources, and other power devices such as switches, circuit breakers, fuses and connectors. Chroma’s DC Electronic Loads are used for power testing in all markets including automatic test systems, LED, power supply testing, battery testing, and fuel cell testing. Chroma loads can do it all including full current down to 0.4VDC, CZ mode, user defined waveforms, timing measurements, and 3 current ranges per load. Chroma’s electronic loads come standard with either USB or RS232 ports for control and can be configured for GPIB (IEEE-488) control as well.
-
Product
Manual Testing Services
-
With manual testing services, we will hand-pick a team dedicated solely to your project. Our professionals will work with your developers, business analysts, and managers to go over requirements, build a comprehensive test plan, design thorough test cases, rapidly execute the tests, help remediate defects, and retest until the project is satisfactorily completed. The same individuals will be with you from beginning to end, so they have a complete understanding of the project and how you want it done, and you will always know exactly who you are dealing with. The same QA Engineers that develop the test cases will also execute them, leaving no room for misunderstandings and greatly expediting the process.
-
Product
3U Rackmount Appliance for PCI Express® Gen4
R300-G4
-
Is a robust, versatile test system designed to test and debug solid state drives (SSDs) of all popular storage interfaces and protocols, such as PCIe, SAS, and SATA.
-
Product
In-Circuit Test Fixture Design Services
-
XJTAG offers consultancy services to design and build production test fixtures that integrate JTAG boundary scan with bed-of-nails testing.
-
Product
Compensating Reactor
RCTD
-
This module is properly designed for testing Tan Delta in rotating machines with TD 5000 and allows increasing the test current and getting the maximum test voltage with high capacitive burdens
