ECU Simulation
a virtual Electronic Control Unit (Engine Control Unit) used to validate related dynamic systems.
See Also: ECU, ECU Testing
-
Product
Flux Valve Simulator
FV Sim
-
This flux valve simulator is designed around the synchro format and is employed in our TA-14 DG panel. This simulator is also available now in a portable enclosure for testing the Sperry or Jet Directional gyros.
-
Product
PXI Dual 16 Channel Switch Simulator
40-485-321
Switch Module
Designed to simulate the operation of automotive switches where dirty contacts or leaking current can be expected from switch contamination. It allows automotive I/O devices to be tested for correct operation under adverse conditions.
-
Product
Circuit Breaker & Control Cabinet Simulator
SIM-CB6
-
The SIM-CB6 is the circuit breaker simulator that will make you an expert in breaker testing. The SIM-CB6 enables you to simulate any type of circuit breaker (SF6, Air Blast, Oil, etc.) up to 6 contacts (2 contacts per phase), with or without closing/opening resistor contacts and control cabinets. This simulator will allow you to increase your knowledge on circuit breaker analyzer systems to ensure full efficiency once on the field.
-
Product
Free Imperas RISC-V Instruction Set Simulator
riscvOVPsim
-
*RiscvOVPsim - RISC-V Instruction Set Simulator (ISS) - fast, simple, easy to use, cross software development for embedded systems*The riscvOVPsim ISS is an ideal starting point for an embedded software development project. *RiscvOVPsim allows the development and debug of code for the target RISC-V processor on an x86 host PC with the minimum of setup and effort. It simply requires the cross compilation of your application and running riscvOVPsim with an argument to specify the name of the application object.
-
Product
ARINC-708/453 2-Channel Test & Simulation Module for the Weather Radar Display Databus
M8K708
Test Module
The M8K708 module is an ARINC-708 / 453 2-channel test and simulation module for the Weather Radar Display Databus. The M8K708 supports two ARINC-708 / 453 channels, each selectable as transmit or receive. Each channel implements an 64K×16 FIFO and supports polling and/or interrupt driven operation.The M8K708 comes complete with Windows software, a C-driver software library including source code and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application. In addition, Excalibur produces adapter cables that convert the carrier board I/O Molex™ connector to two twinax CJ70-49 connectors. The cable may be purchased at an additional cost.
-
Product
PXI Isolated Millivolt Thermocouple Simulator - 8 Channel
41-761-004
Simulator
The use of two wire outputs and isolation from ground ensures that the 41-761 can be used to accurately simulate low voltages even in the presence of common mode voltages in the system. Each Vcold connection is independent permitting the 41-761 to be connected to multiple cold junctions.
-
Product
ARINC825 (CAN Bus) Test & Simulation Module for PCI With 2 Or 4 CAN Bus Nodes
ACP825-x
Simulator
ARINC825 (CAN bus) Test & Simulation module for PCI with 2 or 4 electrically isolated CAN bus nodes operating concurrently at CAN bus high speed bit rate of up to 1Mbit/s. The ACP825-x PCI card can work either with full functionality as an active CAN node for testing and simulating or in Listening Only mode for monitoring and recording purposes.
-
Product
Manikins for realistic simulation of the acoustic properties of a human
Head & Torso Simulators
-
If you need to carry out realistic in-situ measurements of headphones, telephones or hearing aids, you need a Head and Torso Simulator such as the B&K ‘HATS’ – Type 4128D or GRAS’ Kemar to complete your test setup. These manikins have built-in ear and mouth simulators that provide a realistic reproduction of the acoustic properties of an average adult human head and torso. They are commonly used for tests on telephone handsets, headsets, audio conference devices, microphones, headphones, hearing aids and hearing protectors. Please contact your sales engineer or email sales@listeninc.com for more information.
-
Product
Single Stream STANAG3910/EFEX Test And Simulation Module for PCIe
APEX3910
Simulator
STANAG3910/EFEX Test and Simulation module for PCIe with 1 dual redundant HS/LS channel and onboardFibre Optic Front End (FOFE). Easily select between EFAbus and EFEX modes for Tranche II Eurofighter. The APEX3910 is a functional replacementfor model APE3910.
-
Product
PCB Systems Vibration and Acceleration Simulation Solution
Xpedition
-
As the industry’s market share leader in PCB design software, the Mentor Graphics® Xpedition product augments mechanical analysis and physical testing by introducing virtual accelerated lifecycle testing much earlier in the design process. This is the industry’s first PCB-design-specific vibration and acceleration simulation solution targeting products where harsh environments can compromise product performance and reliability, including the military, aerospace, automotive and industrial markets. Traditional, physical HALT (highly accelerated lifecycle testing) is conducted just before volume manufacturing, and requires expert technicians, which can result in costly schedule delays. Bridging mechanical and electronic design disciplines, the Xpedition product provides vibration simulation significantly faster than any existing method. This results in increased test coverage and shortened design cycles to ensure product reliability and faster time to market. The Xpedition component modeling library is the most extensive in the industry, comprised of over 4,000 unique 3D solid models which are used to create highly defined parts for simulation. The 3D library allows users to easily match geometries to their 2D cell database. Designers can assemble the parts models on board and automatically mesh them for performance analysis, including stiffeners and mechanical parts. The system modeling tool is ultra-fast since it can model over 1,000 components per minute.
-
Product
PXI RTD Simulator Module, 4 Channel, PT1000
40-263-503
Simulator
The 40-263-503 is a 4-channel PT1000 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
-
Product
Parallel Simulation Engine
RocketSim
-
Complementing compiled-code simulators, Cadence® RocketSim™ parallel simulation engine eliminates functional verification bottlenecks by speeding up simulation using commonly available multi-core servers.
-
Product
Precision Programmable Regenerative Grid Simulator, 0 - 333VAC, 0 - 3,000A / Phase, 15kVA - 1.08MVA
Sequoia Series
-
AMETEK Programmable Power, Inc.
The California Instruments Sequoia Series combines intelligence and flexibility with high power to create an advanced platform of AC solutions. Using a state-of the-art SiC power switching architecture, this full four quadrant product combines compactness, robustness, and functionality in a floor-standing chassis.
-
Product
Circuit Breaker Simulation Device
PSS01
-
PSS01 is the circuit breaker simulator，which can conduct circuit breaker simulation to test the whole secondary relay scheme together with relay test set. It is very good accessory for protection relay test kit to avoid complicated software programming to finalize the same test.
-
Product
Interference Modeling And Simulation
-
The CAST Navigation Jammers are designed to facilitate and support the testing, verification, and integration of single element Fixed Reception Pattern Antenna (FRPA) systems as well as multiple-element anti-jam antenna sub-systems such as Controlled Reception Pattern Antennas (CRPAs). These systems are an ideal solution for military and commercial laboratories where interference signal capability is required. CAST Jammer sub-systems provide precisely controlled signals for use in most types of GNSS testing applications, emulating interference conditions and threats that can occur in both urban and hostile environments.
-
Product
Damped Oscillatory Wave Simulators
-
Suzhou 3ctest Electronic Co.,Ltd.
Damped oscillatory wave test system for new energy can produce repeatable transient on HV or medium voltage power cord, control line and signal line. It can meet the requirements of CE and CCC certificate. With internal three-phase five-wire high power CDN DOPN 69100T, it can conduct new energy test and high power load test with good reliability, stable performance and easy operation.
-
Product
16-Channel VME Analog Output/Thermocouple Simulator Module
V470
-
The V470 is a 6U VME module that provides sixteen independent, isolated analog outputs that may be user-programmed to operate as voltage outputs or thermocouple simulators. Users may write temperature or voltage values at VMEbus speed, and the microprocessor will transparently do all necessary calculations and update the channel electronics.
-
Product
Handheld ESD Simulator
-
Battery operated handheld ElectroStatic Discharge (ESD) generator up to 30kV.Discharge networks according to IEC 61000-4-2, ISO 10605, MIL-STD-461 CS118, DO-160 section 25 and many more standards.
-
Product
Altitude Digitizer Test Set & Simulator
ATS-400
-
Test & Simulate Altitude Encoder Parallel and Serial I/O all in One Rugged Test Set! The TCI Model ATS-400 is designed to test, display and simulate the output of Altitude Reporting Equipment, which conform to the ICAO Standard for SSR Pressure Altitude Transmission. In accordance with the U.S. National Standards for I.F.F. Mark X (SIF)/Air Traffic Control Radar Beacon System SIF/ATCRBS.
-
Product
4, 8, 16 Or 32 Channel ARINC429 Test And Simulation Modules For VME (6U)
AVC429-x
-
Integrated modular solution by using the AMCX429-x PMC cards installed on AIM’s AVC-2 Generic VME64x (6U) carrier card.
-
Product
PXI Analog Output/Current Loop Simulator Module - 8 Channel
41-765-003
Analog Output Module
The 41/43-765-003 is an 8-channel Analog Output Module designed to meet the requirements of industrial control applications utilizing current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signaling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
-
Product
MCDU Simulator
-
Square Peg Communications Inc.
The Multi-Function Control and Display Unit (MCDU) is an input device for the flight management system and other computer systems of modern aircraft. It consists of a screen and an alphanumeric keyboard and can be found within reach of the pilot in the cockpit of the aircraft. The operation of the MCDU is described in the ARINC 739 specification.
-
Product
ARINC 429 USB & LAN Test & Simulation Module
UXI-429
-
Avionics Interface Technologies
8 Channel (4Tx/4Rx) & 16 Channel (8 Tx/8 Rx) models available - Programmable Tx channel output amplitude - Programmable high/low speed operation - Concurrent operation of all Tx/Rx channels at high speed rates - Full error injection & detection - Rate-oriented label transmission - Label selective trigger for capture/filtering - Real-time recording & post analysis of multiple channels - Physical Bus Replay - Onboard IRIG-B time code encoder/decoder for Synchronization - Time Synchronization to IEEE 1588 via Ethernet LAN port - 10 Discrete I/O Interfaces (5 Outputs / 5 Inputs)
-
Product
Concurrent Alternative RF & GNSS Signal Simulation
SimAltNav Replay
-
Non-GNSS sources of RF (radio frequency) are of interest in GPS-degraded or contested signal environments, with interest focused on LEO (low earth orbit) constellations. These systems offer high receiver signal power (relative to GNSS) and a secure & resilient link to augment GNSS.
-
Product
4, 8, 16 Or 32 Channel ARINC429 Test And Simulation Modules For PMC
AMCX429-x
-
ARINC429 Test and Simulation module for PMC with 4, 8, 16 and 32 programmable Tx/Rx channels plus up to 8 Discrete Inputs/8 Discrete Outputs.
-
Product
Camera Link Simulator
CLS-221
-
The CLS-221 Camera Link Simulator is an affordable, high-performance video test pattern generator that supports all video formats including those introduced in the new version 2.1 specification. Fully programmable video timing enables the CLS-221 to mimic the characteristics of almost any camera. New features include enhanced timing performance, bayer color support, and additional video patterns. Control is via an RS-232 port, USB, or frame grabber COM port. The CLS-221 also incorporates the AIA validation test pattern.
-
Product
O-RU Simulator
-
With Simnovus’s web interface, there is no need to install any software to use the UE simulator.The UE simulator has an intuitive step-by-step workflow to walk users through the generation of even the most complex test profiles in just a few minutes.
-
Product
ACARS CMU Simulator
-
Square Peg Communications Inc.
The SPCI CMU Simulator replaces the ACARS Communications Management Unit for end-to-end testing of the ACARS system. It communicates with an Inmarsat Classic Aero or SB-Safety Satellite Data Unit (SDU) via ARINC-429 to generate and receive ACARS traffic. The CMU Simulator is implemented as a Physical Layer Tester script, and can run on either a BPLT or a GDU. In addition, it can run on a standard PC using a special version of the GDU or BPLT software. In all cases, a suitable ARINC-429 interface must be present.
-
Product
PXI Battery Simulator Modules
-
These PXI battery simulators are designed to simulate the power supplies of portable battery powered equipment and the single cell (model 41-753) is particularly suitable for cell phone testing. These modules can source current to simulate a battery supply or sink current to simulate a battery under charge.
-
Product
MULTI-STANDARD LOCAL LOOP SIMULATOR
458-LM-A8-30
-
Accurately simulates attenuation and impedanceFull bidirectional operation at all specified frequencies26 AWG PIC as specified in ANSI T1.417
